Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1424/24    Solar Sensor Circuit (Driver Side)

for Preparation Click here


DESCRIPTION

The automatic light control sensor (solar sensor), which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning in AUTO mode. The output current from the automatic light control sensor (solar sensor) varies according to the amount of sunlight. When the sunlight increases, the output current increases. As the sunlight decreases, the output current decreases. The air conditioning amplifier assembly detects output current from the automatic light control sensor (solar sensor).
E132508E01

DTC Code
DTC Detection Condition
Trouble Area
B1424/24
An open or short in the driver side solar sensor circuit.
  1. Automatic light control sensor (solar sensor)
  2. Harness or connector between solar sensor and air conditioning amplifier assembly
  3. Harness or connector between solar sensor and main body ECU
  4. Main body ECU (cowl side junction block LH)
  5. Air conditioning amplifier assembly

WIRING DIAGRAM


E147579E07


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE SOLAR SENSOR)
  1. Use the Data List to check if the solar sensor is functioning properly.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Solar Sensor (D Side)
    Driver side solar sensor /
    Min.: 0
    Max.: 255
    Driver side solar sensor voltage increases as brightness increases
    Open in the circuit: 0
    Short in the circuit: 255

    OK:
    The display is as specified in the normal condition.

    Result 
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC output)
    C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
A


2.CHECK HARNESS AND CONNECTOR (SYSTEM VOLTAGE)


    E107010E21
  1. Disconnect the I21 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I21-3 (CLTE) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I21-6 (CLTB) - I21-3 (CLTE)
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - AIR CONDITIONING AMPLIFIER)


    E127612E08
  1. Disconnect the H24 amplifier connector.

  1. Disconnect the I21 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H24-33 (TSD) - I21-1 (TSL)
    Always
    Below 1 Ω
    H24-33 (TSD) or I21-1 (TSL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK AUTOMATIC LIGHT CONTROL SENSOR (TSL - CLTE VOLTAGE)


    E209347E02
  1. Remove the automatic light control sensor (solar sensor) with its connector still connected (Click here).

  1. Apply battery voltage between terminals 6 (CLTB) and 3 (CLTE) of the solar sensor.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1 (TSL) - 3 (CLTE)
    Sensor is subjected to electric light
    0.8 to 4.3 V
    Sensor is covered with a cloth
    Below 0.8 V

    HINT:
    1. As the inspection light is moved away from the sensor, the voltage decreases.
    2. Use an incandescent light for inspection. Bring it about 30 cm (11.8 in.) from the solar sensor.



NG
REPLACE AUTOMATIC LIGHT CONTROL SENSOR (Click here)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR)
E146407E05
  1. Disconnect the H3 ECU connector.

  1. Disconnect the I21 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H3-18 (CLTE) - I21-3 (CLTE)
    Always
    Below 1 Ω
    H3-20 (CLTB) - I21-6 (CLTB)
    Always
    Below 1 Ω
    H3-18 (CLTE) or I21-3 (CLTE) - Body ground
    Always
    10 kΩ or higher
    H3-20 (CLTB) or I21-6 (CLTB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)