Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1443/43    Air Outlet Damper Control Servo Motor Circuit

for Preparation Click here


DESCRIPTION

The cooling unit damper servo sub-assembly (air outlet damper servo motor assembly) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal, reverse) based on the signals to move the air outlet damper to any position, which controls the air outlet changes.

HINT:
Confirm that no mechanical problem is present because this diagnostic trouble code can be stored when either a damper link or damper is mechanically locked.


DTC Code
DTC Detection Condition
Trouble Area
B1443/43
The air outlet damper position does not change even if the air conditioning amplifier assembly operates the air outlet servo motor.
  1. Cooling unit damper servo sub-assembly (Air outlet damper servo motor assembly)
  2. Air conditioning harness assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM


E180810E10


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (AIR OUTLET SERVO MOTOR)
  1. Use the Data List to check if the servo motor is functioning properly.

    Air Conditioner 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    Air Outlet Servo Pulse (D)
    Air outlet servo motor /
    Min.: 0
    Max.: 255
    FACE: 9 (pulse)
    B/L: 32 (pulse)
    FOOT: 56 (pulse)
    FOOT/DEF: 83 (pulse)
    DEF: 9 (pulse)
    -

    OK:
    The display is as specified in the normal condition.

  1. Visually inspect the air outlet servo motor.

    1. Visually inspect whether the air outlet servo motor operates.

      OK:
      The air outlet servo motor operates.

      Result 
      Result
      Proceed to
      The Data List value changes and the air outlet servo motor operates (When troubleshooting according to the DTC output)
      A
      The Data List value changes and the air outlet servo motor operates (When troubleshooting according to Problem Symptoms Table)
      B
      The Data List value does not change and the air outlet servo motor does not operate
      C
      The Data List value changes, but the air outlet servo motor does not operate
      D



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

D
Go to step 3
A


2.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1443/43 is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK COOLING UNIT DAMPER SERVO SUB-ASSEMBLY (AIR OUTLET DAMPER SERVO MOTOR ASSEMBLY)
  1. Replace the cooling unit damper servo sub-assembly (air outlet damper servo motor assembly) (Click here).

    HINT:
    Since the damper servo motor cannot be inspected while it is removed from the vehicle, replace the damper servo motor with a new one and check that the condition returns to normal.

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1443/43 is not output.



NG
Go to step 4
OK

END (COOLING UNIT DAMPER SERVO SUB-ASSEMBLY [AIR OUTLET DAMPER SERVO MOTOR ASSEMBLY] IS FAULTY) 

4.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
  1. Replace the air conditioning harness assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1443/43 is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

END (AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)