Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1446/46    Air Mix Damper Control Servo Motor Circuit (Driver Side)

for Preparation Click here


DESCRIPTION

The cooling unit damper servo sub-assembly (damper servo motor assembly [for driver side]) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal, reverse) based on the signals to move the air mix damper (for driver side) to any position. As a result, the amount of air that has passed through the evaporator and is now passing through the heater core is adjusted, and the temperature of the air blowing toward the driver side is controlled.

HINT:
Confirm that no mechanical problem is present because this diagnostic trouble code can be stored when either a damper link or damper is mechanically locked.


DTC Code
DTC Detection Condition
Trouble Area
B1446/46
The air mix damper position does not change even if the air conditioning amplifier assembly operates the air mix servo motor.
  1. Cooling unit damper servo sub-assembly (Damper servo motor assembly [for driver side])
  2. Air conditioning harness assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM


E180810E12


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE AIR MIX SERVO MOTOR)
  1. Use the Data List to check if the servo motor is functioning properly.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Mix Servo Targ Pulse (D)
    Driver side air mix servo motor /
    Min.: 0
    Max.: 255
    MAX. COLD: 5 (pulse)
    MAX. HOT: 104 (pulse)
    -

    OK:
    The display is as specified in the normal condition.

  1. Visually inspect the driver side air mix servo motor.

    1. Visually inspect whether the driver side air mix servo motor operates.

      OK:
      The driver side air mix servo motor operates.

      Result 
      Result
      Proceed to
      The Data List value changes and the driver side air mix servo motor operates (When troubleshooting according to the DTC output)
      A
      The Data List value changes and the driver side air mix servo motor operates (When troubleshooting according to Problem Symptoms Table)
      B
      The Data List value does not change and the driver side air mix servo motor does not operate
      C
      The Data List value changes, but the driver side air mix servo motor does not operate
      D



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

D
Go to step 3
A


2.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1446/46 is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK COOLING UNIT DAMPER SERVO SUB-ASSEMBLY (DAMPER SERVO MOTOR ASSEMBLY [FOR DRIVER SIDE])
  1. Replace the cooling unit damper servo sub-assembly (damper servo motor assembly [for driver side]) (Click here).

    HINT:
    Since the damper servo motor cannot be inspected while it is removed from the vehicle, replace the damper servo motor with a new one and check that the condition returns to normal.

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1446/46 is not output.



NG
Go to step 4
OK

END (COOLING UNIT DAMPER SERVO SUB-ASSEMBLY [DAMPER SERVO MOTOR ASSEMBLY [FOR DRIVER SIDE] IS FAULTY) 

4.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
  1. Replace the air conditioning harness assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1446/46 is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

END (AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)