DTC B1497/97 BUS IC Communication Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| B1497/97 | An open or error in the communication line. |
|


| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Port | Control Range | Diagnostic Note |
| Air Mix Servo Targ Pulse (D) | Driver side air mix servo motor pulse | Min.: 0, Max.: 255 | - |
| Air Mix Servo Targ Pulse (P) | Passenger side air mix servo motor pulse | Min.: 0, Max.: 255 | - |
| Air Outlet Servo Pulse (D) | Driver side air outlet servo motor pulse | Min.: 0, Max.: 255 | - |
| Air Inlet Damper Targ Pulse | Air inlet damper target pulse | Min.: 0, Max.: 255 | - |
| Cool Air Bypass Pulse | Driver side cool air bypass pulse | Min.: 0, Max.: 255 | - |
| Rear Air Mix Servo Targ Pulse | Rear air mix servo motor pulse | Min.: 0, Max.: 255 | - |
| A/O Servo Pulse (Rr D) | Driver side air outlet servo motor pulse | Min.: 0, Max.: 255 | - |
According to the test, proceed to the next step.
| Result | Proceed to |
| One of the front servo motors is malfunctioning | A |
| All of the front servo motors are malfunctioning | B |
| One of the rear servo motors is malfunctioning | C |
| All of the rear servo motors are malfunctioning | D |
| All of the servo motors are malfunctioning | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.SYSTEM CHECK |
According to the test, proceed to the next step.
| Result | Proceed to |
| Only the air mix damper servo (for driver side) is malfunctioning | A |
| Only the air outlet damper servo is malfunctioning | A |
| Only the air mix damper servo (for passenger side) is malfunctioning | B |
| Only the recirculation damper servo is malfunctioning | C |
| Only the cool air bypass damper servo is malfunctioning | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.REPLACE COOLING UNIT DAMPER SERVO |
Replace the cooling unit damper servo (Click here).
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 4.REPLACE AIR MIX DAMPER SERVO (FOR PASSENGER SIDE) |
Replace the air mix damper servo (for passenger side) (Click here).
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 5.REPLACE RECIRCULATION DAMPER SERVO |
Replace the recirculation damper servo (Click here).
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 6.REPLACE COOL AIR BYPASS DAMPER SERVO |
Replace the cool air bypass damper servo (Click here).
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 7.REPLACE AIR CONDITIONING HARNESS |
Replace the air conditioning harness.
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 8.SYSTEM CHECK |
According to the test, proceed to the next step.
| Result | Proceed to |
| Only the air mix rear damper servo is malfunctioning | A |
| Only the mode rear damper servo is malfunctioning | B |
|
| ||||
| A | |
| 9.REPLACE AIR MIX REAR DAMPER SERVO |
Replace the air mix rear damper servo (Click here).
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
| |||||
| A | ||
| ||
| 10.REPLACE MODE REAR DAMPER SERVO |
Replace the air mix rear damper servo (Click here).
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 11.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - NO. 2 AIR CONDITIONING HARNESS) |
![]() |
Disconnect the P9 No. 2 air conditioning harness assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P9-2 (RBUG) - H67-21 (RBUG) | Always | Below 1 Ω |
| P9-3 (RBUS) - H67-1 (RBUS) | Always | Below 1 Ω |
| P9-4 (RBBU) - H67-23 (RBBU) | Always | Below 1 Ω |
| H67-21 (RBUG) - Body ground | Always | 10 KΩ or higher |
| H67-1 (RBUS) - Body ground | Always | 10 KΩ or higher |
| H67-23 (RBBU) - Body ground | Always | 10 KΩ or higher |
|
| ||||
| OK | |
| 12.REPLACE NO. 2 AIR CONDITIONING HARNESS ASSEMBLY |
Replace the No. 2 air conditioning harness.
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 13.CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
![]() |
Disconnect the H24 and H67 air conditioner amplifier connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H24-21 (B) - Body ground | Always | 11 to 14 V |
| H67-24 (+B2) - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | ||
| ||