Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1497/97    BUS IC Communication Malfunction

for Preparation Click here


DESCRIPTION

The air conditioning harness assembly connects the air conditioning amplifier assembly and each servo motor. The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the air conditioning harness assembly. Each servo motor sends the damper position information to the air conditioning amplifier assembly.

DTC Code
DTC Detection Condition
Trouble Area
B1497/97
An open or error in the communication line.
  1. Air conditioning harness assembly
  2. No. 2 air conditioning harness assembly
  3. Cooling unit damper servo sub-assembly
  4. Air mix damper servo (for passenger side)
  5. Recirculation damper servo
  6. Cool air bypass damper servo
  7. Air mix rear damper servo
  8. Mode rear damper servo
  9. Air conditioning amplifier assembly
  10. Harness or connector

WIRING DIAGRAM


E240076E02


E240332E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

    Air Conditioner 
    Tester Display
    Test Port
    Control Range
    Diagnostic Note
    Air Mix Servo Targ Pulse (D)
    Driver side air mix servo motor pulse
    Min.: 0, Max.: 255
    -
    Air Mix Servo Targ Pulse (P)
    Passenger side air mix servo motor pulse
    Min.: 0, Max.: 255
    -
    Air Outlet Servo Pulse (D)
    Driver side air outlet servo motor pulse
    Min.: 0, Max.: 255
    -
    Air Inlet Damper Targ Pulse
    Air inlet damper target pulse
    Min.: 0, Max.: 255
    -
    Cool Air Bypass Pulse
    Driver side cool air bypass pulse
    Min.: 0, Max.: 255
    -
    Rear Air Mix Servo Targ Pulse
    Rear air mix servo motor pulse
    Min.: 0, Max.: 255
    -
    A/O Servo Pulse (Rr D)
    Driver side air outlet servo motor pulse
    Min.: 0, Max.: 255
    -

    OK:
    Arm of the servo motor selected in the Active Test moves smoothly

  1. According to the test, proceed to the next step.
    Result 
    Result
    Proceed to
    One of the front servo motors is malfunctioning
    A
    All of the front servo motors are malfunctioning
    B
    One of the rear servo motors is malfunctioning
    C
    All of the rear servo motors are malfunctioning
    D
    All of the servo motors are malfunctioning
    E



B
Go to step 7

C
Go to step 8

D
Go to step 11

E
Go to step 13
A


2.SYSTEM CHECK
  1. According to the test, proceed to the next step.
    Result 
    Result
    Proceed to
    Only the air mix damper servo (for driver side) is malfunctioning
    A
    Only the air outlet damper servo is malfunctioning
    A
    Only the air mix damper servo (for passenger side) is malfunctioning
    B
    Only the recirculation damper servo is malfunctioning
    C
    Only the cool air bypass damper servo is malfunctioning
    D



B
Go to step 4

C
Go to step 5

D
Go to step 6
A


3.REPLACE COOLING UNIT DAMPER SERVO
  1. Replace the cooling unit damper servo (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.
    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 7
A

END 

4.REPLACE AIR MIX DAMPER SERVO (FOR PASSENGER SIDE)
  1. Replace the air mix damper servo (for passenger side) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.
    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 7
A

END 

5.REPLACE RECIRCULATION DAMPER SERVO
  1. Replace the recirculation damper servo (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.
    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 7
A

END 

6.REPLACE COOL AIR BYPASS DAMPER SERVO
  1. Replace the cool air bypass damper servo (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.
    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 7
A

END 

7.REPLACE AIR CONDITIONING HARNESS
  1. Replace the air conditioning harness.

    HINT:
    Since the air conditioning harness cannot be inspected while it is removed from the vehicle, replace the air conditioning harness with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.
    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 13
A

END 

8.SYSTEM CHECK
  1. According to the test, proceed to the next step.
    Result 
    Result
    Proceed to
    Only the air mix rear damper servo is malfunctioning
    A
    Only the mode rear damper servo is malfunctioning
    B



B
Go to step 10
A


9.REPLACE AIR MIX REAR DAMPER SERVO
  1. Replace the air mix rear damper servo (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.
    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 11
A

END 

10.REPLACE MODE REAR DAMPER SERVO
  1. Replace the air mix rear damper servo (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.
    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 11
A

END 

11.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - NO. 2 AIR CONDITIONING HARNESS)


    E127593E08
  1. Disconnect the P9 No. 2 air conditioning harness assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P9-2 (RBUG) - H67-21 (RBUG)
    Always
    Below 1 Ω
    P9-3 (RBUS) - H67-1 (RBUS)
    Always
    Below 1 Ω
    P9-4 (RBBU) - H67-23 (RBBU)
    Always
    Below 1 Ω
    H67-21 (RBUG) - Body ground
    Always
    10 KΩ or higher
    H67-1 (RBUS) - Body ground
    Always
    10 KΩ or higher
    H67-23 (RBBU) - Body ground
    Always
    10 KΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.REPLACE NO. 2 AIR CONDITIONING HARNESS ASSEMBLY
  1. Replace the No. 2 air conditioning harness (Click here).

    HINT:
    Since the No. 2 air conditioning harness cannot be inspected while it is removed from the vehicle, replace the No. 2 air conditioning harness with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.
    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 13
A

END 

13.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
E240341E02
  1. Disconnect the H24 and H67 air conditioner amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H24-21 (B) - Body ground
    Always
    11 to 14 V
    H67-24 (+B2) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)