Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING

ROOF HEADLINING > INSTALLATION

for Preparation Click here



1. INSTALL ROOF HEADLINING ASSEMBLY (w/o Rear Seat Entertainment System)


    B193937
  1. Place the roof headlining into the cabin as shown in the illustration.

    NOTICE:
    Be careful not to damage the roof headlining when placing it in the cabin.

  1. Install the washer hose.



  1. Attach the clip to install the roof headlining.


    B193938



    B190136
  1. Install the visor holder with the screw.

    HINT:
    Use the same procedure to install the visor holder on the other side.



    B190127
  1. Attach the 4 clamps to install the amplifier antenna.

  1. Install the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.



    B190126
  1. Install the amplifier antenna with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.



    B190163
  1. Install the washer hose and amplifier antenna.

  1. Connect the connector.



    B190155
  1. Attach the 3 clamps to install the roof wire.

  1. Connect the connector.



2. INSTALL ROOF HEADLINING ASSEMBLY (w/ Rear Seat Entertainment System)


    B193937
  1. Place the roof headlining into the cabin as shown in the illustration.

    NOTICE:
    Be careful not to damage the roof headlining when placing it in the cabin.

  1. Install the washer hose.



  1. Attach the clip to install the roof headlining.


    B193938



    B190136
  1. Install the visor holder with the screw.

    HINT:
    Use the same procedure to install the visor holder on the other side.



    B190127
  1. Attach the 4 clamps to install the amplifier antenna.

  1. Install the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.



    B190126
  1. Install the amplifier antenna with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.



    B190163
  1. Install the washer hose and amplifier antenna.

  1. Connect the connector.



    B193939
  1. Attach the 3 clamps to install the roof wire.

  1. Connect the 2 connectors.



3. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)


    B193936
  1. Place the roof headlining into the cabin as shown in the illustration.

    NOTICE:
    Be careful not to damage the roof headlining when placing it in the cabin.

  1. Install the washer hose.



  1. Attach the clip and 19 fasteners.


    B222462



    B190127
  1. Attach the 4 clamps to install the amplifier antenna.

  1. Install the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.



    B190126
  1. Install the amplifier antenna with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.



    B190163
  1. Install the washer hose and amplifier antenna.

  1. Connect the connector.



    B191808
  1. Attach the 3 clamps to install the roof wire.

  1. Connect the 3 connectors.



4. INSTALL REAR VIEW INNER MIRROR STAY HOLDER COVER (w/ EC Mirror)


B223747E02
  1. w/ Rear Monitor:

    1. Attach the 2 claws of the inner rear view mirror stay holder cover to the mirror, and then slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration to attach the 2 claws to the roof headlining and install the inner rear view mirror stay holder cover.



    B223749
  1. w/o Rear Monitor:

    1. Attach the 6 claws.



5. INSTALL ROOF HEADLINING REAR TRIM COVER LH


    B193893
  1. Attach the 6 claws to install the roof headlining rear trim cover LH.



6. INSTALL ASSIST GRIP PLUG


B165717
  1. Install the new assist grip plug.



7. INSTALL ASSIST GRIP SUB-ASSEMBLY


B169217

HINT:
Use the same procedure for the other 4 assist grips.

  1. Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.

  1. Install the assist grip.



8. INSTALL VISOR ASSEMBLY RH (w/ Illumination)


    B191402
  1. Connect the connector.



    B190133
  1. Install the visor with the 4 screws.



9. INSTALL VISOR ASSEMBLY LH (w/ Illumination)

HINT:
Use the same procedure for both sides.



10. INSTALL VISOR ASSEMBLY RH (w/o Illumination)


    B190135
  1. Install the visor with the 3 screws.



11. INSTALL VISOR ASSEMBLY LH (w/o Illumination)

HINT:
Use the same procedure for both sides.



12. INSTALL VISOR BRACKET COVER RH


B166262
  1. Attach the 4 claws to install the visor bracket cover.



13. INSTALL VISOR BRACKET COVER LH

HINT:
Use the same procedure for both sides.



14. INSTALL NO. 2 ROOM LIGHT ASSEMBLY
  1. Connect the connector.

  1. Attach the 2 claws to install the No. 2 room light.



  1. Attach the 2 claws to install the lens.


    B193063



15. INSTALL NO. 1 ROOM LIGHT ASSEMBLY
  1. Connect the connector.

  1. Attach the 4 clips to install the No. 1 room light.



  1. Attach the 4 claws to install the lens.


    B193921



16. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/ Rear Seat Entertainment System)


    B191797
  1. Connect the connector.



    B193891
  1. Attach the 4 clips to install the No. 1 room light.



17. INSTALL ROOF CONSOLE BOX ASSEMBLY
  1. for Short Type:
    Install the roof console box .

  1. for Long Type:
    Install the roof console box .



18. INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY RH


    B190123
  1. Attach the 5 clips to install the rear window No. 2 side garnish assembly RH.

  1. Install the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B193067
  1. Attach the claw to install the cover.



19. INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY LH (w/o Power Back Door)

HINT:
Use the same procedure for both sides.



20. INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY LH (w/ Power Back Door)


    B191798
  1. Connect the connector.

  1. Attach the 5 clips to install the rear window No. 2 side garnish assembly LH.

  1. Install the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B193892
  1. Attach the claw to install the cover.



21. INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY RH


    B190124
  1. Pass the rear seat outer belt floor anchor through the quarter trim panel.

  1. Attach the 5 clips to install the rear window side garnish.

  1. Install the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B193066
  1. Attach the claw to install the cover.



22. INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY LH

HINT:
Use the same procedure for both sides.



23. INSTALL QUARTER TRIM PANEL ASSEMBLY RH
  1. Connect the connector.

  1. Attach the 11 clips to install the quarter trim panel assembly.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B219907



    B190147
  1. Attach the 2 claws to install the cover.



    B190146
  1. Install the outer lap belt anchor with bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190158
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190145
  1. Attach the 3 claws to install the outer lap belt anchor cover.



24. INSTALL QUARTER TRIM PANEL ASSEMBLY LH
  1. Connect the connector.

  1. Attach the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B222458



    B193068
  1. Attach the 2 claws to install the cover.



    B191816
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Attach the 3 claws to install the outer lap belt anchor cover.



25. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)
  1. Connect the 3 connectors.

  1. Attach the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B222459



    B190147
  1. Attach the 2 claws to install the cover.



    B190146
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190158
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190145
  1. Attach the 3 claws to install the outer lap belt anchor cover.



26. INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Power Seat)
  1. Connect the 5 connectors.

  1. Attach the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Attach the 2 clamps to install the wire harness.



  1. Install the 2 clips.


    B222460



    B193068
  1. Attach the 2 claws to install the cover.



    B191816
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Attach the 3 claws to install the outer lap belt anchor cover.



27. INSTALL REAR FLOOR MAT SUPPORT PLATE


    B190142
  1. Attach the 5 clips and 4 claws to install the rear floor mat support plate.



28. INSTALL ROPE HOOK ASSEMBLY


    B190141
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B190139
  1. Attach the 2 claws to install the cover.



29. INSTALL CENTER PILLAR GARNISH RH
  1. Pass the front seat outer belt floor anchor through the center pillar garnish.

  1. Attach the clip and guide to install the center pillar garnish.

  1. Install the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Install the assist grip with the 2 bolts.

    Torque:
    9.7 N*m{ 99 kgf*cm , 86 in.*lbf }



  1. Attach the 2 claws to install the 2 assist grip plugs.


    B193061



30. INSTALL CENTER PILLAR GARNISH LH

HINT:
Use the same procedure for both sides.



31. INSTALL LOWER CENTER PILLAR GARNISH RH


    B190125
  1. Attach the 7 clips and 2 claws to install the center pillar garnish.



    B190129
  1. Install the front seat outer belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190128
  1. Attach the 3 claws to install the cover.



32. INSTALL LOWER CENTER PILLAR GARNISH LH

HINT:
Use the same procedure for both sides.



33. INSTALL FRONT PILLAR GARNISH RH


    B190132E01
  1. Remove the protective cover.

  1. Attach the claw to install the front pillar garnish.

  1. Install the assist grip with the 2 bolts.

    Torque:
    9.7 N*m{ 99 kgf*cm , 86 in.*lbf }



  1. Attach the 2 claws to install the 2 assist grip plugs.


    B193062



34. INSTALL FRONT PILLAR GARNISH LH

HINT:
Use the same procedure for both sides.



35. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B190154E01
  1. Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.
    Paint Mark 
    Area
    Color
    RH side
    Pink
    LH side
    Purple



36. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



37. INSTALL REAR DOOR SCUFF PLATE RH


    B186666
  1. Attach the 2 claws and 5 clips to install the rear door scuff plate.

  1. Install the 2 bolts.



    B186665
  1. Attach the 6 claws, 5 clips and 2 guides to install the rear door scuff plate.

  1. Install the screw.



38. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



39. INSTALL REAR FLOOR STEP NO. 1 COVER


    B191404
  1. Attach the 2 claws to install the rear floor step No. 1 cover.



40. INSTALL REAR FLOOR STEP NO. 2 COVER


    B193890
  1. Attach the 2 claws to the install the rear floor step No. 2 cover.



41. INSTALL REAR SEAT CUSHION HINGE LOWER COVER RH


    B191794
  1. Attach the 2 clips and 5 claws to install the rear cushion hinge lower cover RH.



42. INSTALL REAR SEAT CUSHION HINGE LOWER COVER LH

HINT:
Use the same procedure for both sides.



43. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B190153E01
  1. Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Paint Mark 
    Area
    Color
    RH side
    White
    LH side
    Yellow



44. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



45. INSTALL COWL SIDE TRIM BOARD RH


    B190152
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the clip.



46. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



47. INSTALL FRONT DOOR SCUFF PLATE RH


B190151
  1. Attach the 9 claws to install the scuff plate.



48. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



49. INSTALL REAR NO. 2 SEAT ASSEMBLY RH
  1. for Manual Seat:
    Install the rear No. 2 seat assembly RH .

  1. for Power Seat:
    Install the rear No. 2 seat assembly RH .



50. INSTALL REAR NO. 2 SEAT ASSEMBLY LH
  1. for Manual Seat:
    Install the rear No. 2 seat assembly LH .

  1. for Power Seat:
    Install the rear No. 2 seat assembly LH .



51. INSTALL DECK BOARD BRACKET


    B190119
  1. Install the deck board bracket with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



52. INSTALL DECK BOARD REINFORCEMENT SUB-ASSEMBLY


    B190120
  1. Install the deck board reinforcement with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



53. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY


    B190117
  1. Attach the 5 clips to install the No. 1 deck board.



54. INSTALL ROPE HOOK ASSEMBLY


    B191405
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    HINT:
    Use the same procedure for both sides.



55. INSTALL LUGGAGE COMPARTMENT TRIM BOX


    B190116
  1. Install the luggage compartment trim box with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B194633
  1. Install the 4 caps.



56. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    B194608
  1. Attach the 4 guides to install the No. 2 deck board.



57. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



58. CHECK SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).