Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Light Control Switch Circuit

for Preparation Click here


DESCRIPTION

The main body ECU receives light control switch, dimmer switch and front fog light switch information signals from the headlight dimmer switch.

WIRING DIAGRAM


E176450E02


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (HEADLIGHT DIMMER SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List /

  1. According to the display on the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Dimmer SW
    Dimmer switch signal / ON or OFF
    ON: Dimmer switch ON
    OFF: Dimmer switch OFF
    -
    Passing Light SW
    Passing light switch signal / ON or OFF
    ON: Passing light switch ON
    OFF: Passing light switch OFF
    -
    Front Fog Light SW*
    Front fog light switch signal / ON or OFF
    ON: Front fog light switch ON
    OFF: Front fog light switch OFF
    -
    Auto Light SW
    Auto light switch signal / ON or OFF
    ON: Auto light switch ON
    OFF: Auto light switch OFF
    -
    Head Light SW (Head)
    Headlight switch signal / ON or OFF
    ON: Headlight switch ON
    OFF: Headlight switch OFF
    -
    Head Light SW (Tail)
    Taillight switch signal / ON or OFF
    ON: Taillight switch ON
    OFF: Taillight switch OFF
    -
    *: w/ Front Fog Light

    OK:
    When combination light switch operation is performed, the result will be the same as above.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY


    E161591E05
  1. Remove the headlight dimmer switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    18 (T) - 12 (EL)
    Light control switch TAIL
    Below 1 Ω
    Light control switch HEAD
    Below 1 Ω
    20 (H) - 12 (EL)
    Light control switch HEAD
    Below 1 Ω
    19 (A) - 12 (EL)
    Light control switch AUTO
    Below 1 Ω
    4 (BFG) - 3 (LFG)*
    Front fog light switch ON
    Below 1 Ω
    17 (HF) - 12 (EL)
    Dimmer switch High
    Below 1 Ω
    11 (HU) - 12 (EL)
    Dimmer switch Low
    Below 1 Ω

    *: w/ Front Fog Light

  1. Reinstall the headlight dimmer switch assembly.



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - MAIN BODY ECU AND BODY GROUND)


    E181627E01
  1. Disconnect the H11 headlight dimmer switch assembly connector.

  1. Disconnect the H3, H4 and DD main body ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H11-4 (BFG) - H3-28 (FFOG)*
    Always
    Below 1 Ω
    H11-19 (A) - H4-21 (A)
    Always
    Below 1 Ω
    H11-20 (H) - H3-17 (HEAD)
    Always
    Below 1 Ω
    H11-18 (T) - H4-23 (TAIL)
    Always
    Below 1 Ω
    H11-17 (HF) - H4-13 (HF)
    Always
    Below 1 Ω
    H11-11 (HU) - DD-13 (HU)
    Always
    Below 1 Ω
    H11-4 (BFG) - Body ground*
    Always
    10 kΩ or higher
    H11-19 (A) - Body ground
    Always
    10 kΩ or higher
    H11-20 (H) - Body ground
    Always
    10 kΩ or higher
    H11-18 (T) - Body ground
    Always
    10 kΩ or higher
    H11-17 (HF) - Body ground
    Always
    10 kΩ or higher
    H11-11 (HU) - Body ground
    Always
    10 kΩ or higher

    *: w/ Front Fog Light

  1. Reconnect the main body ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H11-12 (EL) - Body ground
    Always
    Below 1 Ω
    H11-3 (LFG) - Body ground*
    Always
    Below 1 Ω

    *: w/ Front Fog Light

  1. Reconnect the headlight dimmer switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)