Home › Vehicle Interior › SEAT › REAR SEAT CUSHION HEATER

REAR SEAT CUSHION HEATER > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below are for the LH side.



1. INSTALL SEAT CUSHION HEATER ASSEMBLY


    B191109
  1. Set the seat cushion heater with the name stamp side facing the seat cushion cover.

  1. Install the seat cushion heater with 31 new tack pins.

    NOTICE:
    Do not bend or fold the seat cushion heater assembly.



2. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER


    B191108E03
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

    Text in Illustration 
    *1
    New Hog Ring
    *2
    Hog Ring Pliers



3. INSTALL SEAT CUSHION COVER WITH PAD


    B200247
  1. Attach the hooks to install the rear seat cushion spring.



    B200242E03
  1. Using hog ring pliers, install the seat cushion spring with 9 new hog rings.
    Text in Illustration 
    *1
    New Hog Ring
    *2
    Hog Ring Pliers



4. INSTALL REAR NO. 1 SEAT CUSHION ASSEMBLY RH


    B191091E01
  1. Install the 2 bushes to the cushion spring. Then, using a T45 "TORX" socket wrench, install the 2 "TORX" bolts.

    1. for bolt A

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Install the 2 bolts.

    1. for bolt B

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



    B232099
  1. Fasten the cable to the seat cushion spring with 2 clamps and connect the cable.

    HINT:
    Align the cable with the alignment marks on the seat cushion spring.



    B191089
  1. Fasten the cable with a cable tie.

  1. Attach the cable clamp and connect the cable to the seat cushion spring.



    B191088
  1. Fasten the cable to the seat cushion spring with a cable tie and connect the cable.



    B191090
  1. Connect the connector and attach the 3 harness clamps.

    HINT:
    If the vehicle is equipped with the seat heater system, connect the connector and attach the clamps.



5. INSTALL REAR SEAT CUSHION HINGE COVER NO. 2


B191085
  1. Attach the 2 claws to install the rear seat cushion hinge cover.

  1. Install the screw.



6. INSTALL REAR SEAT CUSHION HINGE COVER NO. 3


B191084
  1. Attach the 2 claws to install the rear seat cushion hinge cover.

  1. Install the screw.



7. INSTALL REAR SEAT RECLINING RELEASE LEVER


    B191083
  1. Install the rear seat reclining release lever with the 3 screws.



8. INSTALL RECLINING ADJUSTER KNOB CAP RH


    B191082
  1. Attach the 3 claws to install the reclining adjuster knob cap.



    B200250E02
  1. Press the pink button on the rear seatback lock control No. 1 cable to release the cable lock, operate the lever a few times to adjust the amount of cable play, and then push in the pink button to lock the cable.
    Text in Illustration 
    *a
    Pink Button



9. INSTALL REAR NO. 1 SEAT ASSEMBLY RH
  1. Install the rear No. 1 seat assembly (Click here).