POWER MIRROR CONTROL SYSTEM (w/ Memory) > Power Retractable Mirrors do not Operate with Power Retract Mirror Switch |

| 1.CHECK FOR DTC |
Use the intelligent tester to check if the CAN communication system is functioning normally (Click here).
| Result | Proceed to |
| CAN DTC is not output | A |
| CAN DTC is output | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (MIRROR RETRACT SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Outer Mirror Fold SW | Mirror retract switch signal / ON or OFF | ON: Mirror retract switch is on (retracting) OFF: Mirror retract switch is off | - |
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MIRROR RETRACT FUNCTION) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Mirror / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Mirror Fold | Mirror retract operation | FOLD/OFF | - |
| Mirror Return | Mirror return operation | RETURN/OFF | - |
| Result | Proceed to |
| Outer rear view mirror operates normally | A |
| Outer rear view mirror LH does not operate normally | B |
| Outer rear view mirror RH does not operate normally | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 4.INSPECT OUTER MIRROR SWITCH (MIRROR RETRACT SWITCH) |
![]() |
Remove the outer mirror switch (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 8 (MF) - 4 (E2) | Pressed (Retracts) | Below 1 Ω |
| Not pressed | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU AND BODY GROUND) |
![]() |
Disconnect the H3 ECU connector.
Disconnect the J6 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J6-4 (E2) - Body ground | Always | Below 1 Ω |
| J6-8 (MF) - H3-6 (RET) | Always | Below 1 Ω |
| J6-8 (MF) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH |
![]() |
Remove the mirror LH (Click here).
Check the retractable mirror's movement.
For each mirror position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.
| Measurement Condition | Mirror Position | Specified Condition |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) | Forward position (A) | Moves from (A) to retracted position (E) |
| Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) | Forward position (A) | Does not move |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) | Position between forward position (A) and driving position (C) | Moves from (B) to retracted position (E) |
| Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) | Position between forward position (A) and driving position (C) | Does not move |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) | Driving position (C) | Moves from (C) to retracted position (E) |
| Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) | Driving position (C) | Does not move |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) | Position between driving position (C) and retracted position (E) | Moves from (D) to retracted position (E) |
| Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) | Position between driving position (C) and retracted position (E) | Does not move |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) | Retracted position (E) | Does not move |
| Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) | Retracted position (E) | Does not move |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU) |
![]() |
Disconnect the M7 ECU connector.
Disconnect the M5 mirror connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M5-7 (MR) - M7-1 (MR+) | Always | Below 1 Ω |
| M5-7 (MR) - Body ground | Always | 10 kΩ or higher |
| M5-8 (MF) - M7-2 (MR-) | Always | Below 1 Ω |
| M5-8 (MF) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH |
![]() |
Remove the mirror RH (Click here).
Check the retractable mirror's movement.
For each mirror position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.
| Measurement Condition | Mirror Position | Specified Condition |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) | Forward position (A) | Moves from (A) to retracted position (E) |
| Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) | Forward position (A) | Does not move |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) | Position between forward position (A) and driving position (C) | Moves from (B) to retracted position (E) |
| Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) | Position between forward position (A) and driving position (C) | Does not move |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) | Driving position (C) | Moves from (C) to retracted position (E) |
| Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) | Driving position (C) | Does not move |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) | Position between driving position (C) and retracted position (E) | Moves from (D) to retracted position (E) |
| Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) | Position between driving position (C) and retracted position (E) | Does not move |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) | Retracted position (E) | Does not move |
| Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) | Retracted position (E) | Does not move |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU) |
![]() |
Disconnect the M7 ECU connector.
Disconnect the L6 mirror connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L6-7 (MR) - M7-5 (MR+) | Always | Below 1 Ω |
| L6-7 (MR) - Body ground | Always | 10 kΩ or higher |
| L6-8 (MF) - M7-6 (MR-) | Always | Below 1 Ω |
| L6-8 (MF) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||