ACCESSORY METER > INSTALLATION |
| 1. INSTALL ACCESSORY METER ASSEMBLY |
Install the accessory meter assembly with the 3 screws.
Connect the connector.
| 2. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY |
Install the register with the 3 <G> or <H> screws.
| 3. INSTALL DEFROSTER NOZZLE ASSEMBLY |
Install the defroster nozzle with the 3 <G> or <H> screws.
| 4. INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT |
Attach the 2 claws to install the duct.
Install the 2 <G> or <H> screws.
| 5. INSTALL NO. 1 SIDE DEFROSTER NOZZLE DUCT |
Attach the 2 claws to install the duct.
Install the 2 <G> or <H> screws.
| 6. INSTALL NO. 1 HEATER TO REGISTER DUCT |
Install the duct with the 5 <G> or <H> screws.
Attach the clamp.
| 7. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (for 8 Speakers) |
Attach the 5 clips to install the instrument panel.
Install the 3 <C> bolts and 2 <E> nuts.
Install the 2 <F> passenger airbag bolts.
Connect the connectors and attach the clamps.
Install the wire harness with the bolt.
![]() |
Connect the airbag connector.
| 8. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (for 14 Speakers) |
Attach the 5 clips to install the instrument panel.
Install the 3 <C> bolts and 2 <E> nuts.
Install the 2 <F> passenger airbag bolts.
Connect the connectors and attach the clamps.
Install the wire harness with the bolt.
![]() |
Connect the airbag connector.
| 9. INSTALL REAR NO. 4 AIR DUCT (for 14 Speakers) |
Attach the 4 claws to install the air duct.
Install the clip.
| 10. INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY (for 14 Speakers) |
![]() |
Install the amplifier with the 3 bolts.
Connect the 4 connectors.
| 11. INSTALL AUDIO AMPLIFIER COVER (for 14 Speakers) |
![]() |
Set the cover on the stereo amplifier assembly.
Attach the 3 clips.
| 12. INSTALL FRONT SEAT ASSEMBLY RH (for 14 Speakers) |
Place the front seat assembly in the cabin.
Connect the seat wire connectors under the seat.
Connect the cable to the negative (-) battery terminal.
![]() |
Operate the leg support adjustment switch to move the seat cushion to the closed position.
Operate the power seat switch (slide switch) to move the seat to the rearmost position.
![]() |
Install the 2 bolts.
Operate the power seat switch (slide switch) to move the seat to the foremost position.
![]() |
Install the 2 bolts.
| 13. INSTALL SEAT TRACK OUTER COVER RH (for 14 Speakers) |
![]() |
Attach the 2 claws to install the seat track cover.
| 14. INSTALL SEAT TRACK INNER COVER RH (for 14 Speakers) |
![]() |
Attach the 2 claws to install the seat track cover.
| 15. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER RH |
Operate the power seat switch (slide switch) to move the seat to the rearmost position.
![]() |
Attach the 4 claws in the order shown in the illustration to install the cover.
| 16. INSTALL FRONT INNER SEAT TRACK BRACKET COVER |
![]() |
Attach the 4 claws in the order shown in the illustration to install the cover.
| 17. INSTALL FRONT SEAT HEADREST ASSEMBLY (for 14 Speakers) |
| 18. INSTALL FRONT NO. 4 SPEAKER ASSEMBLY (for 14 Speakers) |
![]() |
Connect the connector.
Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.
Install the speaker with the 2 bolts.
| 19. INSTALL NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Attach the 6 clips and 2 claws to install the speaker panel.
| 20. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY RH |
![]() |
Connect the speaker connector.
Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.
Install the speaker with the 2 bolts.
| 21. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Attach the 4 clips and claw to install the speaker panel.
| 22. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY LH |
![]() |
Connect the speaker connector.
Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.
Install the speaker with the 2 bolts.
| 23. INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Attach the 4 clips and claw to install the speaker panel.
| 24. INSTALL NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY |
Attach the clip to install the box door.
Install the 6 <B> or <H> screws.
| 25. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH |
Connect the connector.
Attach the 3 claws to install the finish panel.
Install the 3 <D> screws and bolt <A>.
| 26. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY |
![]() |
Connect the connector.
Install the 3 bolts to install the instrument panel airbag.
| 27. INSTALL LOWER INSTRUMENT PANEL |
Attach the 2 claws to install the panel.
Install the bolt <A> and screw <D>.
| 28. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
Attach the 2 guides and 4 claws.
Attach the clip to install the under cover.
| 29. INSTALL INSTRUMENT SIDE PANEL RH |
![]() |
Attach the 6 claws to install the side panel.
| 30. INSTALL FRONT PILLAR GARNISH RH |
![]() |
Remove the protective cover.
Attach the claw to install the front pillar garnish.
Install the assist grip with the 2 bolts.
Attach the 2 claws to install the 2 assist grip plugs.

| 31. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
| Area | Color |
| RH side | White |
| LH side | Yellow |
| 32. INSTALL COWL SIDE TRIM BOARD RH |
![]() |
Attach the 2 clips to install the cowl side trim board.
Install the clip.
| 33. INSTALL FRONT DOOR SCUFF PLATE RH |
![]() |
Attach the 9 claws to install the scuff plate.
| 34. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver) |
![]() |
Connect the connectors.
Insert the radio receiver and attach the 3 clips on its backside.
![]() |
Install the radio receiver with the 4 bolts.
| 35. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System for HDD) |
Connect the connectors.
![]() |
Insert the navigation receiver as shown in the illustration to attach the 3 clips on its backside.
![]() |
Install the navigation receiver with the 4 bolts.
| 36. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY |
![]() |
Connect the connectors.
Attach the 4 clips and install the panel.
| 37. INSTALL CENTER LOWER INSTRUMENT PANEL FINISH PANEL |
Connect the connectors.
Attach the 4 clips and 2 claws to install the finish panel.
| 38. INSTALL COMBINATION METER ASSEMBLY |
Connect the connector and attach the wire harness clamp.
Install the combination meter assembly with the 4 screws.
| 39. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
Attach the 12 clips to install the finish panel.
Connect the 2 connectors and clamp.
Attach the 4 claws to install the instrument panel finish panel retainer.
| 40. INSTALL FRONT CONSOLE BOX |
![]() |
Install the front console box with the 5 screws and 2 clips.
Attach the 2 clamps.
| 41. INSTALL REAR CONSOLE BOX ASSEMBLY (w/o Cool Box) |
![]() |
Attach the 6 claws to install the rear console box.
Install the 2 screws and 4 bolts.
![]() |
Connect the connectors.
| 42. INSTALL CONSOLE BOX CARPET (w/o Cool Box) |
![]() |
Install the console box carpet.
| 43. INSTALL REAR CONSOLE BOX POCKET (w/o Cool Box) |
![]() |
Install the rear console box pocket.
| 44. INSTALL REAR CONSOLE BOX ASSEMBLY (w/ Cool Box) |
Attach the 6 claws to install the rear console box.
Install the 2 screws and 4 bolts.
Connect the 2 connectors.
| 45. INSTALL COOLING BOX ASSEMBLY (w/ Cool Box) |
Attach the 4 clips and claw and install the cooling box assembly.
Install 4 new No. 1 cool box packings.
Install the 4 bolts.
Connect the 3 connectors.
| 46. INSTALL COOLING BOX TRAY (w/ Cool Box) |
Install the cooling box tray.
| 47. CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (w/ Cool Box) |
Remove the attached vinyl tape from the air conditioner tube and accessory assembly.
Sufficiently apply compressor oil to 2 new O-rings and to the fitting surface of the cooling box assembly.
Install the 2 O-rings on the air conditioner tube and accessory assembly.
Connect the air conditioner tube and accessory assembly to the cooling box assembly with the 2 bolts.
| 48. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Connect the connectors.
Attach the 6 clips to install the console panel.
Install the clip.
| 49. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Attach the 12 clips to install the console panel.
| 50. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY |
![]() |
Install the shift lever knob and twist it in the direction indicated by the arrow.
| 51. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY |
![]() |
Connect the connector.
Attach the 2 claws to install the DLC3.
Install the 4 bolts to install the instrument panel airbag.
| 52. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH |
Attach the 2 claws to install the sensor.
Connect the connectors.
Attach the 9 clips and claw to install the finish panel.
Install the 2 <A> bolts.
| 53. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Connect the hood lock control cable assembly to the hood lock control lever sub-assembly.
Attach the 3 claws to install the hood lock lever
| 54. INSTALL INSTRUMENT SIDE PANEL LH |
![]() |
Attach the 7 claws to install the side panel.
| 55. INSTALL FRONT PILLAR GARNISH LH |
| 56. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 57. INSTALL COWL SIDE TRIM BOARD LH |
| 58. INSTALL FRONT DOOR SCUFF PLATE LH |
| 59. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Install the turn signal switch with spiral cable to the steering column with the clamp.
![]() |
Connect the 6 connectors to the turn signal switch with spiral cable.
| 60. INSTALL UPPER STEERING COLUMN COVER |
![]() |
Attach the claw to install the upper steering column cover.
Attach the 4 clips.
| 61. INSTALL LOWER STEERING COLUMN COVER |
![]() |
Attach the 2 claws to install the lower steering column cover.
Install the 2 screws.
| 62. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
Align the matchmarks on the steering wheel and steering main shaft.
| *a | Matchmark |
Install the steering wheel set nut.
| 63. INSTALL STEERING PAD |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Support the steering pad with one hand.
![]() |
Connect the 2 airbag connectors to the steering pad.
Push in the 2 connector locks to install the 2 airbag connectors.
Connect the horn connector to the steering pad.
Install the steering pad.
![]() |
Using a T30 "TORX" socket wrench, tighten the 2 screws.
| 64. INSTALL LOWER NO. 3 STEERING WHEEL COVER |
![]() |
Attach the guide and claw to install the lower No. 3 steering wheel cover.
| 65. INSTALL LOWER NO. 2 STEERING WHEEL COVER |
![]() |
Attach the guide and claw to install the lower No. 2 steering wheel cover.
| 66. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 67. CHARGE REFRIGERANT (w/ Cool Box) |

Perform vacuum purging using a vacuum pump.
Charge refrigerant HFC-134a (R134a).
| Cool Box | Refrigerant Charging Amount |
| w/ Cool Box | 1080 to 1140 g (38.1 to 40.2 oz.) |
| w/o Cool Box | 920 to 980 g (32.4 to 34.6 oz.) |

Install the caps onto the service valves on the refrigerant line.
| 68. WARM UP ENGINE (w/ Cool Box) |
| 69. INSPECT FOR REFRIGERANT LEAK (w/ Cool Box) |
After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.
Perform the operation as follows:
![]() |
Using the halogen leak detector, check the refrigerant line, especially at the connection points, for leakage.
If no gas leakage is detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.
Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.
| 70. CHECK SRS WARNING LIGHT |