Home › Vehicle Interior › METER / GAUGE / DISPLAY › ACCESSORY METER

ACCESSORY METER > INSTALLATION

for Preparation Click here



1. INSTALL ACCESSORY METER ASSEMBLY
  1. Install the accessory meter assembly with the 3 screws.

  1. Connect the connector.



2. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY
  1. Install the register with the 3 <G> or <H> screws.



3. INSTALL DEFROSTER NOZZLE ASSEMBLY
  1. Install the defroster nozzle with the 3 <G> or <H> screws.



4. INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT
  1. Attach the 2 claws to install the duct.

  1. Install the 2 <G> or <H> screws.



5. INSTALL NO. 1 SIDE DEFROSTER NOZZLE DUCT
  1. Attach the 2 claws to install the duct.

  1. Install the 2 <G> or <H> screws.



6. INSTALL NO. 1 HEATER TO REGISTER DUCT
  1. Install the duct with the 5 <G> or <H> screws.

  1. Attach the clamp.



7. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (for 8 Speakers)
  1. Attach the 5 clips to install the instrument panel.

  1. Install the 3 <C> bolts and 2 <E> nuts.

  1. Install the 2 <F> passenger airbag bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the connectors and attach the clamps.

  1. Install the wire harness with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



    B228242
  1. Connect the airbag connector.



8. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (for 14 Speakers)
  1. Attach the 5 clips to install the instrument panel.

  1. Install the 3 <C> bolts and 2 <E> nuts.

  1. Install the 2 <F> passenger airbag bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the connectors and attach the clamps.

  1. Install the wire harness with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



    B228242
  1. Connect the airbag connector.



9. INSTALL REAR NO. 4 AIR DUCT (for 14 Speakers)
  1. Attach the 4 claws to install the air duct.

  1. Install the clip.



10. INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY (for 14 Speakers)


    B190161
  1. Install the amplifier with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 4 connectors.



11. INSTALL AUDIO AMPLIFIER COVER (for 14 Speakers)


    B190162
  1. Set the cover on the stereo amplifier assembly.

  1. Attach the 3 clips.



12. INSTALL FRONT SEAT ASSEMBLY RH (for 14 Speakers)
  1. Place the front seat assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect the seat wire connectors under the seat.

  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



    B167189
  1. Operate the leg support adjustment switch to move the seat cushion to the closed position.

  1. Operate the power seat switch (slide switch) to move the seat to the rearmost position.



    B194824
  1. Install the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Operate the power seat switch (slide switch) to move the seat to the foremost position.



    B191041
  1. Install the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



13. INSTALL SEAT TRACK OUTER COVER RH (for 14 Speakers)


    B200255
  1. Attach the 2 claws to install the seat track cover.



14. INSTALL SEAT TRACK INNER COVER RH (for 14 Speakers)


    B191067
  1. Attach the 2 claws to install the seat track cover.



15. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER RH
  1. Operate the power seat switch (slide switch) to move the seat to the rearmost position.



    B232178E01
  1. Attach the 4 claws in the order shown in the illustration to install the cover.



16. INSTALL FRONT INNER SEAT TRACK BRACKET COVER


    B232179E01
  1. Attach the 4 claws in the order shown in the illustration to install the cover.



17. INSTALL FRONT SEAT HEADREST ASSEMBLY (for 14 Speakers)


18. INSTALL FRONT NO. 4 SPEAKER ASSEMBLY (for 14 Speakers)


    B165751E01
  1. Connect the connector.

  1. Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.

  1. Install the speaker with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful that the wires do not get caught between the parts.



19. INSTALL NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


B192348
  1. Attach the 6 clips and 2 claws to install the speaker panel.



20. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY RH


    E161074
  1. Connect the speaker connector.

  1. Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.

  1. Install the speaker with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful that the wires do not get caught between the parts.



21. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


B192350
  1. Attach the 4 clips and claw to install the speaker panel.



22. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY LH


    E161075
  1. Connect the speaker connector.

  1. Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.

  1. Install the speaker with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful that the wires do not get caught between the parts.



23. INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


B192346
  1. Attach the 4 clips and claw to install the speaker panel.



24. INSTALL NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY
  1. Attach the clip to install the box door.

  1. Install the 6 <B> or <H> screws.



25. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH
  1. Connect the connector.

  1. Attach the 3 claws to install the finish panel.

  1. Install the 3 <D> screws and bolt <A>.



26. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B226008
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Install the 3 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



27. INSTALL LOWER INSTRUMENT PANEL
  1. Attach the 2 claws to install the panel.

  1. Install the bolt <A> and screw <D>.



28. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
  1. Attach the 2 guides and 4 claws.

  1. Attach the clip to install the under cover.



29. INSTALL INSTRUMENT SIDE PANEL RH


    B229198
  1. Attach the 6 claws to install the side panel.



30. INSTALL FRONT PILLAR GARNISH RH


    B190132E01
  1. Remove the protective cover.

  1. Attach the claw to install the front pillar garnish.

  1. Install the assist grip with the 2 bolts.

    Torque:
    9.7 N*m{ 99 kgf*cm , 86 in.*lbf }



  1. Attach the 2 claws to install the 2 assist grip plugs.


    B193062



31. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B190153E01
  1. Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Paint Mark 
    Area
    Color
    RH side
    White
    LH side
    Yellow



32. INSTALL COWL SIDE TRIM BOARD RH


    B190152
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the clip.



33. INSTALL FRONT DOOR SCUFF PLATE RH


B190151
  1. Attach the 9 claws to install the scuff plate.



34. INSTALL RADIO RECEIVER ASSEMBLY (w/o Navigation System)
  1. for Radio Receiver Type:

  1. for Radio and Display Type:



35. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System for HDD)
  1. Connect each connector.

  1. Insert the navigation receiver assembly and attach the 2 guides and 3 clips on its backside.

    NOTICE:
    When inserting the navigation receiver, do not press its knobs.

  1. Install the navigation receiver assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



36. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


    I104352
  1. Connect the connectors.

  1. Attach the 4 clips and install the panel.



37. INSTALL CENTER LOWER INSTRUMENT PANEL FINISH PANEL
  1. Connect the connectors.

  1. Attach the 4 clips and 2 claws to install the finish panel.



38. INSTALL COMBINATION METER ASSEMBLY
  1. Connect the connector and attach the wire harness clamp.

  1. Install the combination meter assembly with the 4 screws.



39. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
  1. Attach the 12 clips to install the finish panel.

  1. Connect the 2 connectors and clamp.

  1. Attach the 4 claws to install the instrument panel finish panel retainer.



40. INSTALL FRONT CONSOLE BOX


B222975
  1. Install the front console box with the 5 screws and 2 clips.

  1. Attach the 2 clamps.



41. INSTALL REAR CONSOLE BOX ASSEMBLY (w/o Cool Box)


B192330
  1. Attach the 6 claws to install the rear console box.

  1. Install the 2 screws and 4 bolts.



    B188223
  1. Connect the connectors.



42. INSTALL CONSOLE BOX CARPET (w/o Cool Box)


B188222
  1. Install the console box carpet.



43. INSTALL REAR CONSOLE BOX POCKET (w/o Cool Box)


B188221
  1. Install the rear console box pocket.



44. INSTALL REAR CONSOLE BOX ASSEMBLY (w/ Cool Box)
  1. Attach the 6 claws to install the rear console box.

  1. Install the 2 screws and 4 bolts.

  1. Connect the 2 connectors.



45. INSTALL COOLING BOX ASSEMBLY (w/ Cool Box)
  1. Attach the 4 clips and claw and install the cooling box assembly.

  1. Install 4 new No. 1 cool box packings.

  1. Install the 4 bolts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the 3 connectors.



46. INSTALL COOLING BOX TRAY (w/ Cool Box)
  1. Install the cooling box tray.



47. CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (w/ Cool Box)
  1. Remove the attached vinyl tape from the air conditioner tube and accessory assembly.

  1. Sufficiently apply compressor oil to 2 new O-rings and to the fitting surface of the cooling box assembly.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-rings on the air conditioner tube and accessory assembly.

  1. Connect the air conditioner tube and accessory assembly to the cooling box assembly with the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



48. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY


    B222976
  1. Connect the connectors.

  1. Attach the 6 clips to install the console panel.

  1. Install the clip.



49. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    B161742
  1. Attach the 12 clips to install the console panel.



50. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    B167312
  1. Install the shift lever knob and twist it in the direction indicated by the arrow.



51. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B225998
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Attach the 2 claws to install the DLC3.

  1. Install the 4 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



52. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH
  1. Attach the 2 claws to install the sensor.

  1. Connect the connectors.

  1. Attach the 9 clips and claw to install the finish panel.

  1. Install the 2 <A> bolts.



53. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B192511
  1. Connect the hood lock control cable assembly to the hood lock control lever sub-assembly.

  1. Attach the 3 claws to install the hood lock lever



54. INSTALL INSTRUMENT SIDE PANEL LH


    B229058
  1. Attach the 7 claws to install the side panel.



55. INSTALL FRONT PILLAR GARNISH LH

HINT:
Use the same procedure for both sides.



56. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



57. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



58. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



59. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    C159216
  1. Install the turn signal switch with spiral cable to the steering column with the clamp.



    C180951
  1. Connect the 6 connectors to the turn signal switch with spiral cable.



60. INSTALL UPPER STEERING COLUMN COVER


    C159215
  1. Attach the claw to install the upper steering column cover.

  1. Attach the 4 clips.



61. INSTALL LOWER STEERING COLUMN COVER


    C181134
  1. Attach the 2 claws to install the lower steering column cover.

  1. Install the 2 screws.



62. INSTALL STEERING WHEEL ASSEMBLY


    C290041E01
  1. Align the matchmarks on the steering wheel and steering main shaft.
    Text in Illustration 
    *a
    Matchmark

  1. Install the steering wheel set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



63. INSTALL STEERING PAD
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Support the steering pad with one hand.



    B354950
  1. Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.

  1. Push in the 2 connector locks to install the 2 airbag connectors.

  1. Connect the horn connector to the steering pad.

  1. Install the steering pad.



    B354952
  1. Using a T30 "TORX" socket wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



64. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    B355450
  1. Attach the guide and claw to install the lower No. 3 steering wheel cover.



65. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    B355451
  1. Attach the guide and claw to install the lower No. 2 steering wheel cover.



66. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

CAUTION:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



67. CHARGE REFRIGERANT (w/ Cool Box)



I100449E02

NOTICE:
Charge refrigerant in accordance with the equipment manual.

  1. Perform vacuum purging using a vacuum pump.

  1. Charge refrigerant HFC-134a (R134a).

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    Standard:
    Cool Box
    Refrigerant Charging Amount
    w/ Cool Box
    1080 to 1140 g (38.1 to 40.2 oz.)
    w/o Cool Box
    920 to 980 g (32.4 to 34.6 oz.)

    NOTICE:
    Do not start the engine before charging it with refrigerant as the cooler compressor does not work properly without sufficient refrigerant. This could cause the compressor to overheat.

    HINT:

    1. The relationship between the refrigerant charge amount and the pressure is as follows.


      I103968E01

    2. High Charge Range:
      If the refrigerant is overcharged, the pressure rises on the high-pressure side. High-pressure cut off frequently occurs. This causes insufficient cooling performance and also insufficient compressor lubrication.
    3. Low Charge Range:
      A shortage of refrigerant causes insufficient cooling performance and low circulation of refrigerant oil, which shortens the compressor life. Operation with insufficient coolant raises the refrigerant temperature and causes heat deterioration of the rubber seals and hoses. Cracking and subsequent refrigerant leakage may occur.


    1. Install the caps onto the service valves on the refrigerant line.



68. WARM UP ENGINE (w/ Cool Box)


69. INSPECT FOR REFRIGERANT LEAK (w/ Cool Box)
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation as follows:

    1. Stop the engine.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system.
      When the compressor is off: approximately 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)

    HINT:
    It is impossible for the above pressure to be maintained if there is leakage.



    I042222E14
  1. Using the halogen leak detector, check the refrigerant line, especially at the connection points, for leakage.

  1. If no gas leakage is detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.



70. CHECK SRS WARNING LIGHT
(Click here)