ACCESSORY METER > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE LOWER NO. 2 STEERING WHEEL COVER |
![]() |
Using a screwdriver, detach the 2 claws and remove the steering wheel cover.
| 3. REMOVE LOWER NO. 3 STEERING WHEEL COVER |
![]() |
Using a screwdriver, detach the 2 claws and remove the steering wheel cover.
| 4. REMOVE STEERING PAD |
![]() |
Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.
Pull the steering pad toward you.
![]() |
Using a thin-bladed screwdriver, release the locking button.
Using a thin-bladed screwdriver, disconnect the 2 connectors.
Disconnect the horn connector.
| 5. REMOVE STEERING WHEEL ASSEMBLY |
![]() |
Detach the cruise control main wire harness clamp from the steering wheel side.
Disconnect the steering pad switch connector and cruise control main switch connector from the spiral cable.
Remove the steering wheel set nut.
![]() |
Put matchmarks on the steering wheel and main shaft.
Using SST, remove the steering wheel.
| 6. REMOVE LOWER STEERING COLUMN COVER |
![]() |
Remove the 2 screws.
Detach the 2 claws to remove the lower steering column cover.
| 7. REMOVE UPPER STEERING COLUMN COVER |
![]() |
Detach the 4 clips.
Detach the claw to remove the upper steering column cover.
| 8. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Disconnect the all connectors from the turn signal switch with spiral cable.
![]() |
Using pliers, grip the claws of the clamp and remove the turn signal switch with spiral cable from the steering column.
| 9. REMOVE FRONT DOOR SCUFF PLATE LH |
| 10. REMOVE COWL SIDE TRIM BOARD LH |
| 11. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 12. REMOVE FRONT PILLAR GARNISH LH |
| 13. REMOVE INSTRUMENT SIDE PANEL LH |
![]() |
Using a moulding remover, detach the 7 claws and remove the side panel.
| 14. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Detach the 3 claws.
Disconnect the hood lock control cable and remove the hood lock control lever sub-assembly.
| 15. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH |
![]() |
Remove the 2 <A> bolts.
Detach the 9 clips and claw.
![]() |
Detach the 2 claws and remove the sensor.
Remove the finish panel and then disconnect the connectors.
| 16. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY |
![]() |
Remove the 4 bolts and remove the instrument panel airbag.
Detach the 2 claws and disconnect the DLC3.
Disconnect the connector.
| 17. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY |
![]() |
Twist the shift lever knob in the direction indicated by the arrow and remove it.
| 18. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Detach the 12 clips and remove the console panel.
| 19. REMOVE REAR CONSOLE BOX POCKET |
![]() |
Remove the rear console box pocket.
| 20. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Move the shift lever to N.
Remove the clip.
Detach the 6 clips and remove the console panel.
Disconnect the connector
| 21. REMOVE CONSOLE BOX CARPET |
![]() |
Remove the console box carpet.
| 22. REMOVE REAR CONSOLE BOX ASSEMBLY |
![]() |
Disconnect the connectors.
![]() |
Remove the 4 bolts and 2 screws.
Detach the 6 claws and remove the rear console box.
| 23. REMOVE FRONT CONSOLE BOX |
![]() |
Detach the 2 clamps.
Remove the 2 clips.
Remove the 5 screws and the front console box.
| 24. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
![]() |
Detach the 4 claws and remove the instrument panel finish panel retainer.
![]() |
Disconnect the 2 connectors and wire harness clamp.
Detach the 12 clips and remove the finish panel.
| 25. REMOVE COMBINATION METER ASSEMBLY |
![]() |
Remove the 4 screws.
![]() |
Disconnect the connector and disengage the clip and remove the combination meter assembly.
| 26. REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL |
![]() |
Detach the 4 clips and 2 claws.
Disconnect the connectors and remove the finish panel.
| 27. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY |
![]() |
Detach the 4 clips and separate the panel.
Disconnect the connectors and remove the panel.
| 28. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver) |
![]() |
Remove the 4 bolts.
![]() |
Pull the radio receiver to detach the 3 clips on the backside of the radio receiver.
Disconnect the connectors and remove the radio receiver.
| 29. REMOVE UPPER INSTRUMENT CLUSTER FINISH PANEL WITH BRACKET (w/o Radio Receiver) |
![]() |
Remove the 4 bolts.
![]() |
Detach the 3 clips and remove the upper instrument cluster finish panel with bracket.
| 30. REMOVE INSTRUMENT SIDE PANEL RH |
![]() |
Using a moulding remover, detach the 6 claws and remove the side panel.
| 31. REMOVE FRONT DOOR SCUFF PLATE RH |
![]() |
Detach the 9 claws and remove the scuff plate.
| 32. REMOVE COWL SIDE TRIM BOARD RH |
![]() |
Remove the clip.
Detach the 2 clips and remove the cowl side trim board.
| 33. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Remove the front door opening trim weatherstrip.
| 34. REMOVE FRONT PILLAR GARNISH RH |
Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the 2 assist grip plugs.
Remove the 2 bolts and assist grip.
Detach the claw and remove the front pillar garnish.

![]() |
Protect the curtain shield airbag.
Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.
| 35. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() |
Detach the clip and 4 claws.
Detach the 2 guides and remove the under cover.
| 36. REMOVE LOWER INSTRUMENT PANEL |
![]() |
Remove the screw and bolt.
Detach the 2 claws and remove the panel.
| 37. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY |
![]() |
Remove the 3 bolts and remove the instrument panel airbag.
Disconnect the connector.
| 38. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH |
![]() |
Remove the bolt <A> and 3 <D> screws.
Detach the 3 claws and remove the finish panel.
![]() |
Disconnect the connector.
| 39. REMOVE NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY |
![]() |
Remove the 6 <B> screws.
Detach the clip and remove the box door.
| 40. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Using a moulding remover, detach the 4 clips and claw, and remove the speaker panel.
| 41. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY LH |
![]() |
Remove the 2 bolts.
Remove the speaker and disconnect the connector.
| 42. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Using a moulding remover, detach the 4 clips and claw, and remove the speaker panel.
| 43. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY RH |
![]() |
Remove the 2 bolts.
Remove the speaker and disconnect the connector.
| 44. REMOVE NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Using a moulding remover, detach the 6 clips and 2 claws, and remove the speaker panel.
| 45. REMOVE FRONT NO. 4 SPEAKER ASSEMBLY (for 14 Speakers) |
![]() |
Remove the 2 bolts.
Remove the speaker and disconnect the connector.
| 46. REMOVE FRONT SEAT HEADREST ASSEMBLY (for 14 Speakers) |
| 47. REMOVE FRONT INNER SEAT TRACK BRACKET COVER (for 14 Speakers) |
Operate the power seat switch (slide switch) to move the seat to the rearmost position.
![]() |
Using a screwdriver, detach the 4 claws in the order shown in the illustration and remove the cover.
| 48. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER RH (for 14 Speakers) |
![]() |
Using a screwdriver, detach the 4 claws in the order shown in the illustration and remove the cover.
| 49. REMOVE SEAT TRACK INNER COVER RH (for 14 Speakers) |
Operate the power seat switch (slide switch) to move the seat to the foremost position.
![]() |
Using a screwdriver, detach the 2 claws and remove the cover.
| 50. REMOVE SEAT TRACK OUTER COVER RH (for 14 Speakers) |
![]() |
Using a screwdriver, detach the 2 claws and remove the cover.
| 51. REMOVE FRONT SEAT ASSEMBLY RH (for 14 Speakers) |
Operate the power seat switch (slide switch) to move the seat to the foremost position.
![]() |
Remove the 2 bolts.
Operate the power seat switch (slide switch) to move the seat to the rearmost position.
![]() |
Remove the 2 bolts.
Operate the power seat switch (slide switch) to move the seat to the center position.
![]() |
Operate the leg support adjustment switch to move the seat cushion to the open position.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the seat wire connectors under the seat.
Remove the front seat assembly from the vehicle.
| 52. REMOVE AUDIO AMPLIFIER COVER (for 14 Speakers) |
![]() |
Detach the 3 clips and remove the cover.
| 53. REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY (for 14 Speakers) |
![]() |
Disconnect the 4 connectors.
Remove the 3 bolts and amplifier.
| 54. REMOVE REAR NO. 4 AIR DUCT (for 14 Speakers) |
![]() |
Remove the clip.
Detach the 4 claws and remove the air duct.
| 55. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for 14 Speakers) |
![]() |
Slide the slider and disconnect the airbag connector.
Detach the clamp and disconnect the connectors.
Remove the bolt and wire harness.

Remove the 2 <F> passenger airbag bolts.
Remove the 3 <C> bolts and 2 <E> nuts.

Detach the 5 clips and remove the instrument panel.

| 56. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for 8 Speakers) |
![]() |
Slide the slider and disconnect the airbag connector.
Detach the clamp and disconnect the connectors.
Remove the bolt and wire harness.

Remove the 2 <F> passenger airbag bolts.
Remove the 3 <C> bolts and 2 <E> nuts.

Detach the 5 clips and remove the instrument panel.

| 57. REMOVE NO. 3 INSTRUMENT PANEL STAY |
Detach the 3 claws and remove the 3 stays.

| 58. REMOVE NO. 1 HEATER TO REGISTER DUCT |
Detach the clamp.
Remove the 5 screws and duct.

| 59. REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT |
![]() |
Remove the 2 screws.
Detach the 2 claws and remove the duct.
| 60. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT |
![]() |
Remove the 2 screws.
Detach the 2 claws and remove the duct.
| 61. REMOVE DEFROSTER NOZZLE ASSEMBLY |
![]() |
Remove the 3 screws and defroster nozzle.
| 62. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Remove the 3 screws and register.
| 63. REMOVE ACCESSORY METER ASSEMBLY |
Disconnect the connector.
![]() |
Remove the 3 screws and remove the accessory meter assembly.