ACCESSORY METER > REMOVAL |
| 1. PRECAUTION |
| 2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Cool Box) |
Start up the engine.
Switch A/C ON.
Turn the blower switch to ON.
Operate the cooler compressor with an engine speed of approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the remaining compressor oil from each component, in the cooler compressor.
Stop the engine.
![]() |
Remove the caps from the service valves on the refrigerant line.
| *1 | Low Pressure Service Valve |
| *2 | High Pressure Service Valve |
Connect the refrigerant recovery unit.
Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.
| 3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 4. REMOVE LOWER NO. 2 STEERING WHEEL COVER |
![]() |
Using a screwdriver, detach the claw and guide and remove the lower No. 2 steering wheel cover.
| *1 | Protective Tape |
| 5. REMOVE LOWER NO. 3 STEERING WHEEL COVER |
![]() |
Using a screwdriver, detach the claw and guide and remove the lower No. 3 steering wheel cover.
| *1 | Protective Tape |
| 6. REMOVE STEERING PAD |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
![]() |
Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.
Pull the steering pad toward you.
![]() |
Disconnect the horn connector from the steering pad.
Using a screwdriver, release the 2 airbag connector locks.
| *1 | Protective Tape |
Disconnect the 2 airbag connectors to remove the steering pad as shown in the illustration.
| 7. REMOVE STEERING WHEEL ASSEMBLY |
![]() |
Disconnect the 2 connectors from the spiral cable.
Remove the steering wheel set nut.
![]() |
Put matchmarks on the steering wheel and main shaft.
| *a | Matchmark |
| *b | Hold |
| *c | Turn |
Using SST, remove the steering wheel.
| 8. REMOVE LOWER STEERING COLUMN COVER |
![]() |
Remove the 2 screws.
Detach the 2 claws to remove the lower steering column cover.
| 9. REMOVE UPPER STEERING COLUMN COVER |
Detach the 4 clips.
![]() |
Detach the claw to remove the upper steering column cover.
| 10. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Disconnect the all connectors from the turn signal switch with spiral cable.
![]() |
Using pliers, grip the claws of the clamp and remove the turn signal switch with spiral cable from the steering column.
| 11. REMOVE FRONT DOOR SCUFF PLATE LH |
| 12. REMOVE COWL SIDE TRIM BOARD LH |
| 13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 14. REMOVE FRONT PILLAR GARNISH LH |
| 15. REMOVE INSTRUMENT SIDE PANEL LH |
![]() |
Using a moulding remover, detach the 7 claws and remove the side panel.
| 16. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Detach the 3 claws.
Disconnect the hood lock control cable and remove the hood lock control lever sub-assembly.
| 17. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH |
![]() |
Remove the 2 <A> bolts.
Detach the 9 clips and claw.
![]() |
Detach the 2 claws and remove the sensor.
Remove the finish panel and then disconnect the connectors.
| 18. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY |
![]() |
Remove the 4 bolts and remove the instrument panel airbag.
Detach the 2 claws and disconnect the DLC3.
Disconnect the connector.
| 19. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY |
![]() |
Twist the shift lever knob in the direction indicated by the arrow and remove it.
| 20. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Detach the 12 clips and remove the console panel.
| 21. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Move the shift lever to N.
Remove the clip.
Detach the 6 clips and remove the console panel.
Disconnect the connector.
| 22. DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (w/ Cool Box) |
![]() |
Remove the 2 bolts and disconnect the air conditioner tube and accessory assembly from the cooling box assembly.
Remove the 2 O-rings from the air conditioner tube and accessory assembly.
| 23. REMOVE COOLING BOX TRAY (w/ Cool Box) |
![]() |
Remove the cooling box tray.
| 24. REMOVE COOLING BOX ASSEMBLY (w/ Cool Box) |
![]() |
Disconnect the 3 connectors.
![]() |
Remove the 4 bolts.
Remove the 4 No. 1 cool box packings.
![]() |
Detach the 4 clips and claw, and remove the cooling box assembly.
| 25. REMOVE REAR CONSOLE BOX ASSEMBLY (w/ Cool Box) |
![]() |
Disconnect the 2 connectors.
![]() |
Remove the 4 bolts and 2 screws.
Detach the 6 claws and remove the rear console box.
| 26. REMOVE REAR CONSOLE BOX POCKET (w/o Cool Box) |
![]() |
Remove the rear console box pocket.
| 27. REMOVE CONSOLE BOX CARPET (w/o Cool Box) |
![]() |
Remove the console box carpet.
| 28. REMOVE REAR CONSOLE BOX ASSEMBLY (w/o Cool Box) |
![]() |
Disconnect the connectors.
![]() |
Remove the 4 bolts and 2 screws.
Detach the 6 claws and remove the rear console box.
| 29. REMOVE FRONT CONSOLE BOX |
![]() |
Detach the 2 clamps.
Remove the 2 clips.
Remove the 5 screws and the front console box.
| 30. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
![]() |
Detach the 4 claws and remove the instrument panel finish panel retainer.
![]() |
Disconnect the 2 connectors and wire harness clamp.
Detach the 12 clips and remove the finish panel.
| 31. REMOVE COMBINATION METER ASSEMBLY |
![]() |
Remove the 4 screws and combination meter assembly.
![]() |
Disconnect the connector and detach the wire harness clamp.
| 32. REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL |
![]() |
Detach the 4 clips and 2 claws.
Disconnect the connectors and remove the finish panel.
| 33. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY |
![]() |
Detach the 4 clips and separate the panel.
Disconnect the connectors and remove the panel.
| 34. REMOVE RADIO RECEIVER ASSEMBLY (w/o Navigation System) |
for Radio Receiver Type:
for Radio and Display Type:
| 35. REMOVE NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System) |
![]() |
Remove the 4 bolts.
![]() |
Pull the navigation receiver assembly to detach the 3 clips and 2 guides on the backside of the navigation receiver assembly.
Disconnect each connector and remove the navigation receiver assembly.
| 36. REMOVE FRONT DOOR SCUFF PLATE RH |
![]() |
Detach the 9 claws and remove the scuff plate.
| 37. REMOVE COWL SIDE TRIM BOARD RH |
![]() |
Remove the clip.
Detach the 2 clips and remove the cowl side trim board.
| 38. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Remove the front door opening trim weatherstrip.
| 39. REMOVE FRONT PILLAR GARNISH RH |
Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the 2 assist grip plugs.
Remove the 2 bolts and assist grip.
Detach the claw and remove the front pillar garnish.

![]() |
Protect the curtain shield airbag.
Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.
| 40. REMOVE INSTRUMENT SIDE PANEL RH |
![]() |
Using a moulding remover, detach the 6 claws and remove the side panel.
| 41. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() |
Detach the clip and 4 claws.
Detach the 2 guides and remove the under cover.
| 42. REMOVE LOWER INSTRUMENT PANEL |
![]() |
Remove the screw <D> and bolt <A>.
Detach the 2 claws and remove the panel.
| 43. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY |
![]() |
Remove the 3 bolts and remove the instrument panel airbag.
Disconnect the connector.
| 44. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH |
![]() |
Remove the bolt <A> and 3 <D> screws.
Detach the 3 claws and remove the finish panel.
![]() |
Disconnect the connector.
| 45. REMOVE NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY |
![]() |
Remove the 6 <B> or <H> screws.
Detach the clip and remove the box door.
| 46. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Using a moulding remover, detach the 4 clips and claw, and remove the speaker panel.
![]() | Protective Tape |
| 47. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY LH |
![]() |
Remove the 2 bolts.
Remove the speaker and disconnect the connector.
| 48. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Using a moulding remover, detach the 4 clips and claw, and remove the speaker panel.
![]() | Protective Tape |
| 49. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY RH |
![]() |
Remove the 2 bolts.
Remove the speaker and disconnect the connector.
| 50. REMOVE NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Using a moulding remover, detach the 6 clips and 2 claws, and remove the speaker panel.
![]() | Protective Tape |
| 51. REMOVE FRONT NO. 4 SPEAKER ASSEMBLY (for 14 Speakers) |
![]() |
Remove the 2 bolts.
Remove the speaker and disconnect the connector.
| 52. REMOVE FRONT SEAT HEADREST ASSEMBLY (for 14 Speakers) |
| 53. REMOVE FRONT INNER SEAT TRACK BRACKET COVER |
Operate the power seat switch (slide switch) to move the seat to the rearmost position.
![]() |
Using a screwdriver, detach the 4 claws in the order shown in the illustration and remove the cover.
| 54. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER RH |
![]() |
Using a screwdriver, detach the 4 claws in the order shown in the illustration and remove the cover.
| 55. REMOVE SEAT TRACK INNER COVER RH (for 14 Speakers) |
Operate the power seat switch (slide switch) to move the seat to the foremost position.
![]() |
Using a screwdriver, detach the 2 claws and remove the cover.
| 56. REMOVE SEAT TRACK OUTER COVER RH (for 14 Speakers) |
![]() |
Using a screwdriver, detach the 2 claws and remove the cover.
| 57. REMOVE FRONT SEAT ASSEMBLY RH (for 14 Speakers) |
Operate the power seat switch (slide switch) to move the seat to the foremost position.
![]() |
Remove the 2 bolts.
Operate the power seat switch (slide switch) to move the seat to the rearmost position.
![]() |
Remove the 2 bolts.
Operate the power seat switch (slide switch) to move the seat to the center position.
![]() |
Operate the leg support adjustment switch to move the seat cushion to the open position.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the seat wire connectors under the seat.
Remove the front seat assembly from the vehicle.
| 58. REMOVE AUDIO AMPLIFIER COVER (for 14 Speakers) |
![]() |
Detach the 3 clips and remove the cover.
| 59. REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY (for 14 Speakers) |
![]() |
Disconnect the 4 connectors.
Remove the 3 bolts and amplifier.
| 60. REMOVE REAR NO. 4 AIR DUCT (for 14 Speakers) |
![]() |
Remove the clip.
Detach the 4 claws and remove the air duct.
| 61. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for 14 Speakers) |
![]() |
Slide the slider and disconnect the airbag connector.
| *1 | Slider |
Detach the clamp and disconnect the connectors.
Remove the bolt and wire harness.

Remove the 2 <F> passenger airbag bolts.
Remove the 3 <C> bolts and 2 <E> nuts.

Detach the 5 clips and remove the instrument panel.

| 62. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for 8 Speakers) |
![]() |
Slide the slider and disconnect the airbag connector.
| *1 | Slider |
Detach the clamp and disconnect the connectors.
Remove the bolt and wire harness.

Remove the 2 <F> passenger airbag bolts.
Remove the 3 <C> bolts and 2 <E> nuts.

Detach the 5 clips and remove the instrument panel.

| 63. REMOVE NO. 1 HEATER TO REGISTER DUCT |
Detach the clamp.
Remove the 5 <G> or <H> screws and duct.

| 64. REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT |
![]() |
Remove the 2 <G> or <H> screws.
Detach the 2 claws and remove the duct.
| 65. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT |
![]() |
Remove the 2 <G> or <H> screws.
Detach the 2 claws and remove the duct.
| 66. REMOVE DEFROSTER NOZZLE ASSEMBLY |
![]() |
Remove the 3 <G> or <H> screws and defroster nozzle.
| 67. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Remove the 3 <G> or <H> screws and register.
| 68. REMOVE ACCESSORY METER ASSEMBLY |
Disconnect the connector.
![]() |
Remove the 3 screws and accessory meter assembly.