Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR

REAR DOOR > DISASSEMBLY

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the RH side.



1. DISCONNECT CABLE TO NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE REAR DOOR FRAME GARNISH


    B190577
  1. Detach the 6 clips and remove the rear door frame garnish.



3. REMOVE REAR DOOR ARMREST BASE UPPER PANEL


    B190574
  1. Detach the 2 clips and 5 claws and remove the rear door armrest base upper panel.



4. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    B190575
  1. Using a moulding remover, detach the 4 claws and remove the rear door inside handle bezel plug.



5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


B190578
  1. Remove the rear door armrest cover.

  1. Remove the 2 screws.



    B190579
  1. Detach the 9 clips.

  1. Disconnect the connector.



    B190580
  1. Disconnect the rear door lock remote control cable and the rear door inside locking cable and remove the rear door trim board sub-assembly.



6. REMOVE REAR DOOR INSIDE HANDLE BEZEL


    B190544
  1. Remove the 4 screws and remove the rear door inside handle bezel.



7. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    B190545
  1. Remove the 3 screws and remove the rear door inside handle sub-assembly.



8. REMOVE REAR DOOR GLASS INNER WEATHERSTRIP


    B190581
  1. Raise the 8 claws of the rear door glass inner weatherstrip and then remove the rear door glass inner weatherstrip from the rear door trim board sub-assembly, as shown in the illustration.



9. REMOVE REAR NO. 1 SPEAKER ASSEMBLY


    E161073
  1. Disconnect the speaker connector.

  1. Remove the 3 screws.



    E161077
  1. Detach the 2 claws and remove the speaker.

    NOTICE:
    Do not touch the cone part of the speaker.



10. REMOVE REAR DOOR TRIM NO. 2 BRACKET


    B190583
  1. Remove the 2 screws and remove the rear door trim No. 2 bracket.



11. REMOVE REAR DOOR SERVICE HOLE COVER


    B190584
  1. Detach the clamps and disconnect the connectors.



    B195023
  1. Remove the rear door service hole cover.

    NOTICE:
    Remove any tape remaining on the door.



12. REMOVE REAR DOOR WINDOW FRAME REAR MOULDING

HINT:
When removing the rear door window frame rear moulding, heat the vehicle body and rear door window frame rear moulding using a heat light.

Standard:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Rear Door Window Frame Rear Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or rear door window frame rear moulding excessively.



    B256625E01
  1. Put protective tape around the rear door window frame rear moulding.

  1. Using a moulding remover, detach the 2 clips and remove the double-sided tape to remove the rear door window frame rear moulding.



13. REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP


B191703E01
  1. Apply protective tape to the door panel in the area around the rear door glass outer weatherstrip.



    B191704E01
  1. Using a moulding remover, detach the 5 claws and the clip, and remove the rear door glass outer weatherstrip.



14. REMOVE REAR DOOR GLASS RUN


    B190585
  1. Remove the rear door glass run.



15. REMOVE SUNSHADE HOOK


    B194495E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 sunshade hooks.



16. REMOVE REAR DOOR WINDOW FRAME REAR LOWER SUB-ASSEMBLY


    B190586E01
  1. Loosen nut A.

  1. Remove the 3 bolts and rear door window frame rear lower sub-assembly.

    NOTICE:
    Do not drop or damage the rear door window frame rear lower sub-assembly.



17. REMOVE REAR DOOR WINDOW GUIDE FRONT SUB-ASSEMBLY


    B190587
  1. Remove the 2 bolts and rear door window guide front sub-assembly.

    NOTICE:
    Do not drop or damage the rear door window guide front sub-assembly when removing the bolts.



18. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


B190588
  1. Provisionally install the power window switch.

  1. Move the rear door glass until the 2 bolts can be seen through the service holes.

  1. Remove the 2 bolts and remove the rear door glass sub-assembly.

    NOTICE:
    Do not damage the door glass.



19. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


    B192108E01
  1. Disconnect the connector.

  1. Loosen the bolt labeled A.

  1. Remove the 5 bolts and remove the rear door window regulator sub-assembly.

    NOTICE:
    Do not damage the rear door window regulator sub-assembly.

  1. Remove the bolt labeled A from the front door window regulator assembly.



20. REMOVE REAR DOOR CHECK ASSEMBLY


    B190589
  1. Remove the bolt and 2 nuts.

  1. Remove the rear door check assembly.

    NOTICE:
    Do not drop or damage the rear door check assembly when removing the bolt and nuts.



21. REMOVE REAR DOOR WEATHERSTRIP


    B192109
  1. Detach the 42 clips and remove the rear door weatherstrip.



22. REMOVE REAR DOOR NO. 2 WEATHERSTRIP


    B192110
  1. Detach the 17 clips and remove rear door No. 2 weatherstrip.



23. REMOVE REAR DOOR LOCK


    B192117
  1. Using a T30 "TORX" socket wrench, remove the 3 screws.

  1. Move the rear door lock downward and pull the release plate out of the rear door outside handle frame.

  1. Remove the door lock wire harness seal from the rear door lock.



    B192545E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the claw and open the cover.



    B192547
  1. Remove the rear door lock remote control cable.



    B192548E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 3 claws and open the cover.



    B192550
  1. Remove the rear door inside locking cable.



24. REMOVE REAR DOOR OUTSIDE HANDLE COVER


    B192111
  1. Using a T30 "TORX" wrench, remove the screw and the rear door outside handle cover.



25. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY


    B192112
  1. Remove the rear door outside handle assembly by sliding and pulling it in the direction indicated by the arrow mark in the illustration.



26. REMOVE REAR DOOR OUTSIDE HANDLE REAR PAD


    B192115
  1. Detach the 2 claws and remove the rear door outside handle rear pad.



27. REMOVE REAR DOOR OUTSIDE HANDLE FRONT PAD


    B192116
  1. Detach the 2 claws and remove the rear door outside handle front pad.



28. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    B190568
  1. Using a T30 "TORX" wrench, loosen the screw.

  1. Detach the claw and slide the rear door outside handle frame sub-assembly to remove it.



29. REMOVE CUSHION


    B192118
  1. Remove the cushions from the door panel.