REAR DOOR > REASSEMBLY |
| 1. INSTALL CUSHION |
![]() |
Install the cushions onto the door panel.
| 2. INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
![]() |
Slide the rear door outside handle frame subassembly and attach the claw and install it.
Using a T30 "TORX" wrench, tighten the screw.
| 3. INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD |
![]() |
Attach the 2 claws to install the rear door outside handle front pad.
| 4. INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD |
![]() |
Attach the 2 claws and install the rear door outside handle rear pad.
| 5. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY |
![]() |
Install the rear door outside handle assembly by pushing it in the direction indicated by the arrow mark shown in the illustration.
| 6. INSTALL REAR DOOR OUTSIDE HANDLE COVER |
![]() |
Using a T30 "TORX" wrench, install the rear door outside handle cover with the screw.
| 7. INSTALL REAR DOOR LOCK |
Apply MP grease to the sliding and rotating areas of the front door lock.
![]() |
Install the rear door inside locking cable.
![]() |
Attach the 3 claws to close the cover.
![]() |
Install the rear door lock remote control cable.
![]() |
Attach the claw to close the cover.
Install a new door lock wire harness seal on to the rear door lock.
![]() |
Insert the rear door lock into the rear door outside handle release plate, and set it to the rear door panel.
Make sure that the rear door outside handle frame lock.
Apply adhesive to the threads of the screws.
Using a T30 "TORX" socket wrench, install the rear door lock with the 3 screws.
| 8. INSTALL REAR DOOR NO. 2 WEATHERSTRIP |
![]() |
Attach the 17 clips to install the rear door No. 2 weatherstrip.
| 9. INSTALL REAR DOOR WEATHERSTRIP |
![]() |
Attach the 42 clips to install the rear door weatherstrip.
| 10. INSTALL REAR DOOR CHECK ASSEMBLY |
![]() |
Apply MP grease to the sliding areas of the rear door check assembly.
Install the rear door check assembly onto the door panel with the 2 nuts.
Apply adhesive to the threads of the bolt.
Install the rear door check assembly onto the body panel with the bolt.
| 11. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY |
Apply MP grease to the sliding and rotating areas of the rear door window regulator sub-assembly.
![]() |
Loosely install the bolt labeled A onto the window regulator sub-assembly.
Insert the rear door window regulator sub-assembly into the door panel. Provisionally tighten bolt A to hang the rear door window regulator sub-assembly on the door panel.
Install the front door window regulator sub-assembly with the 5 bolts, and tighten the bolt labeled A.
Connect the connector.
| 12. INSTALL REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Install the rear door glass sub-assembly onto the rear door window regulator with the 2 bolts.
| 13. INSTALL REAR DOOR WINDOW GUIDE FRONT SUB-ASSEMBLY |
![]() |
Install the rear door window guide front sub-assembly with the 2 bolts
| 14. INSTALL REAR DOOR WINDOW FRAME REAR LOWER SUB-ASSEMBLY |
![]() |
Install the rear door window frame rear lower sub-assembly with the nut and 3 bolts.
| 15. INSTALL SUNSHADE HOOK |
![]() |
Attach the claw and install the sunshade hook.
| 16. INSTALL REAR DOOR GLASS RUN |
![]() |
Install the rear door glass run.
| 17. INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP |
![]() |
Attach the 9 claws to install the back door glass outer weatherstrip.
| 18. INSTALL REAR DOOR WINDOW FRAME REAR MOULDING |
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Rear Door Window Frame Rear Moulding | 20 to 30°C (68 to 86°F) |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove the double-sided tape from the vehicle body surface.
Wipe off any tape adhesive residue with cleaner.
![]() |
Install a new rear door window frame rear moulding.
Using a heat light, heat a new rear door window frame rear moulding and the vehicle body surface.
Remove the peeling paper from the face of the rear door window frame rear moulding.
Attach the 2 clips and double-sided tape to install the rear door window frame rear moulding.
| 19. INSTALL REAR DOOR SERVICE HOLE COVER |
![]() |
Apply butyl tape to the door panel, then install a new rear door service hole cover as shown in the illustration.
![]() |
Attach the clamps and connect the connectors.
| 20. INSTALL REAR DOOR TRIM NO. 2 BRACKET |
![]() |
Install the rear door trim No. 2 bracket with the 2 screws.
| 21. INSTALL REAR NO. 1 SPEAKER ASSEMBLY |
![]() |
Attach the 2 claws.
![]() |
Install the speaker with the 3 screws.
Connect the connector.
| 22. INSTALL REAR DOOR GLASS INNER WEATHERSTRIP |
![]() |
Install the rear door glass inner weatherstrip on the rear door trim board sub-assembly and fold down the 8 claws, as shown in the illustration.
| 23. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Install the rear door inside handle sub-assembly with the 3 screws.
| 24. INSTALL REAR DOOR INSIDE HANDLE BEZEL |
![]() |
Install the rear door inside handle bezel with the 4 screws.
| 25. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Connect the rear door lock remote control cable and the rear door inside locking cable.
Connect the connector.
![]() |
Attach the 9 clips to install the rear door trim board sub-assembly.
![]() |
Tighten the 2 screws.
Install the rear door armrest cover.
| 26. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Attach the 4 claws to install the rear door inside handle bezel plug.
| 27. INSTALL REAR DOOR ARMREST BASE UPPER PANEL |
Connect the connector.
![]() |
Attach the 2 clips and 5 claws to install the rear door armrest base upper panel.
| 28. INSTALL REAR DOOR FRAME GARNISH |
![]() |
Attach the 6 clips to install the rear door frame garnish.
| 29. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 30. CHECK SRS WARNING LIGHT |
Check the SRS warning light (Click here).