Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)

STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column) > INSTALLATION

for Preparation Click here



1. INSTALL STEERING COLUMN ASSEMBLY


C180952E01
  1. Install the steering column with the bolt and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the connectors and wire harness clamps.



2. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


C155151E01
  1. Align the matchmarks on the No. 2 steering intermediate shaft and power steering gear.

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



3. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY


C155150E01
  1. Align the matchmarks on the steering intermediate shaft and No. 2 steering intermediate shaft.

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



    C154524E01
  1. Align the matchmarks on the steering column and steering intermediate shaft.

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



    C155149
  1. Install the 3 bolts and nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



4. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY


    C154523
  1. Install the air duct with the bolt.



5. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY


    B225998
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Attach the 2 claws to install the DLC3.

  1. Install the 4 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



6. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B163883
  1. Attach the 2 claws to install the sensor.



    B229064
  1. Connect the connectors.

  1. Attach the 9 clips and claw to install the finish panel.

  1. Install the 2 <A> bolts.



7. INSTALL INSTRUMENT SIDE PANEL LH


    B229058
  1. Attach the 7 claws to install the side panel.



8. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



9. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab)

HINT:
Use the same procedure for both sides.



10. INSTALL COMBINATION SWITCH


    C159216
  1. Install the turn signal switch with spiral cable to the steering column with the clamp.



    C180951
  1. Connect the 6 connectors to the turn signal switch with spiral cable.



11. INSTALL UPPER STEERING COLUMN COVER


C159215
  1. Attach the claw to install the upper steering column cover.

  1. Attach the 4 clips.



12. INSTALL LOWER STEERING COLUMN COVER


C181134
  1. Attach the 2 claws to install the lower steering column cover.

  1. Install the 2 screws.



13. ADJUST SPIRAL CABLE


    B166449
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Rotate the spiral cable with steering sensor counterclockwise slowly by hand until it feels firm.

    NOTICE:
    Do not turn the spiral cable with steering sensor by the airbag wire harness.



    B166450
  1. Rotate the spiral cable with steering sensor clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable with spiral sensor by the airbag wire harness.

    HINT:
    The spiral cable with steering sensor will rotate approximately 2.5 turns to both the left and right from the center.



14. INSTALL STEERING WHEEL ASSEMBLY


    C181135E01
  1. Align the matchmarks on the steering wheel and steering main shaft.

  1. Install the steering wheel set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



15. INSPECT STEERING WHEEL CENTER POINT


16. INSTALL STEERING PAD

NOTICE:
Do not use a steering pad that has been dropped.



    B166581
  1. Check that the ignition switch is turned off.

  1. Check that the negative battery terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Connect the horn connector.

  1. Connect the airbag connector.

    NOTICE:
    1. Match the color of the airbag connector with that of the steering pad assembly, and install the airbag connector.
    2. Securely lock the locking button.

  1. Install the steering pad.



    C180935
  1. Using T30 "TORX" socked wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



17. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    B166432
  1. Attach the 2 claws to install the cover.



18. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    B166433
  1. Attach the 2 claws to install the cover.



19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



20. INSPECT SRS WARNING LIGHT
  1. (Click here).