STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column) > INSTALLATION |
| 1. INSTALL STEERING COLUMN ASSEMBLY |
![]() |
Install the steering column with the bolt and 2 nuts.
Connect the connectors and wire harness clamps.
| 2. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
![]() |
Align the matchmarks on the No. 2 steering intermediate shaft and power steering gear.
| *a | Matchmark |
Install the bolt.
| 3. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Align the matchmarks on the steering intermediate shaft and No. 2 steering intermediate shaft.
| *a | Matchmark |
Install the bolt.
![]() |
Align the matchmarks on the steering column and steering intermediate shaft.
| *a | Matchmark |
Install the bolt.
![]() |
Install the 3 bolts and nut.
| 4. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY |
![]() |
Install the air duct with the bolt.
| 5. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY |
![]() |
Connect the connector.
Attach the 2 claws to install the DLC3.
Install the 4 bolts to install the instrument panel airbag.
| 6. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH |
Attach the 2 claws to install the sensor.
Connect the connectors.
Attach the 9 clips and claw to install the finish panel.
Install the 2 <A> bolts.
| 7. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Connect the hood lock control cable assembly to the hood lock control lever sub-assembly.
Attach the 3 claws to install the hood lock lever
| 8. INSTALL INSTRUMENT SIDE PANEL LH |
![]() |
Attach the 7 claws to install the side panel.
| 9. INSTALL COWL SIDE TRIM BOARD LH |
| 10. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab) |
| 11. INSTALL COMBINATION SWITCH |
![]() |
Install the turn signal switch with spiral cable to the steering column with the clamp.
![]() |
Connect the 6 connectors to the turn signal switch with spiral cable.
| 12. INSTALL UPPER STEERING COLUMN COVER |
![]() |
Attach the claw to install the upper steering column cover.
Attach the 4 clips.
| 13. INSTALL LOWER STEERING COLUMN COVER |
![]() |
Attach the 2 claws to install the lower steering column cover.
Install the 2 screws.
| 14. ADJUST SPIRAL CABLE |
![]() |
Check that the ignition switch is off.
Check that the battery negative (-) terminal is disconnected.
Rotate the spiral cable with steering sensor counterclockwise slowly by hand until it feels firm.
![]() |
Rotate the spiral cable with steering sensor clockwise approximately 2.5 turns to align the marks.
| 15. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
Align the matchmarks on the steering wheel and steering main shaft.
| *a | Matchmark |
Install the steering wheel set nut.
| 16. INSPECT STEERING WHEEL CENTER POINT |
| 17. INSTALL STEERING PAD |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Support the steering pad with one hand.
![]() |
Connect the 2 airbag connectors to the steering pad.
Push in the 2 connector locks to install the 2 airbag connectors.
Connect the horn connector to the steering pad.
Install the steering pad.
![]() |
Using a T30 "TORX" socket wrench, tighten the 2 screws.
| 18. INSTALL LOWER NO. 3 STEERING WHEEL COVER |
![]() |
Attach the guide and claw to install the lower No. 3 steering wheel cover.
| 19. INSTALL LOWER NO. 2 STEERING WHEEL COVER |
![]() |
Attach the guide and claw to install the lower No. 2 steering wheel cover.
| 20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 21. CHECK SRS WARNING LIGHT |
(Click here).