Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)

STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) > INSTALLATION

for Preparation Click here



1. INSTALL STEERING COLUMN ASSEMBLY


    C180953E01
  1. Install the steering column with the bolt and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the connectors and wire harness clamps.



2. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    C155151E02
  1. Align the matchmarks on the No. 2 steering intermediate shaft and power steering gear.
    Text in Illustration 
    *a
    Matchmark

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



3. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY


    C155150E02
  1. Align the matchmarks on the steering intermediate shaft and No. 2 steering intermediate shaft.
    Text in Illustration 
    *a
    Matchmark

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



    C154524E02
  1. Align the matchmarks on the steering column and steering intermediate shaft.
    Text in Illustration 
    *a
    Matchmark

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



    C155149
  1. Install the 3 bolts and nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



4. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY


    C154523
  1. Install the air duct with the bolt.



5. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B225998
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Attach the 2 claws to install the DLC3.

  1. Install the 4 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



6. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH
  1. Attach the 2 claws to install the sensor.

  1. Connect the connectors.

  1. Attach the 9 clips and claw to install the finish panel.

  1. Install the 2 <A> bolts.



7. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B192511
  1. Connect the hood lock control cable assembly to the hood lock control lever sub-assembly.

  1. Attach the 3 claws to install the hood lock lever



8. INSTALL INSTRUMENT SIDE PANEL LH


    B229058
  1. Attach the 7 claws to install the side panel.



9. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



10. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



11. INSTALL COMBINATION SWITCH


    C159216
  1. Install the turn signal switch with spiral cable to the steering column with the clamp.



    C180951
  1. Connect the 6 connectors to the turn signal switch with spiral cable.



12. INSTALL UPPER STEERING COLUMN COVER


    C159215
  1. Attach the claw to install the upper steering column cover.

  1. Attach the 4 clips.



13. INSTALL LOWER STEERING COLUMN COVER


    C181134
  1. Attach the 2 claws to install the lower steering column cover.

  1. Install the 2 screws.



14. ADJUST SPIRAL CABLE


    B166449
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Rotate the spiral cable with steering sensor counterclockwise slowly by hand until it feels firm.

    NOTICE:
    Do not turn the spiral cable with steering sensor by the airbag wire harness.



    B166450
  1. Rotate the spiral cable with steering sensor clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable with spiral sensor by the airbag wire harness.

    HINT:
    The spiral cable with steering sensor will rotate approximately 2.5 turns to both the left and right from the center.



15. INSTALL STEERING WHEEL ASSEMBLY


    C290041E01
  1. Align the matchmarks on the steering wheel and steering main shaft.
    Text in Illustration 
    *a
    Matchmark

  1. Install the steering wheel set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



16. INSPECT STEERING WHEEL CENTER POINT


17. INSTALL STEERING PAD
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Support the steering pad with one hand.



    B354950
  1. Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.

  1. Push in the 2 connector locks to install the 2 airbag connectors.

  1. Connect the horn connector to the steering pad.

  1. Install the steering pad.



    B354952
  1. Using a T30 "TORX" socket wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



18. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    B355450
  1. Attach the guide and claw to install the lower No. 3 steering wheel cover.



19. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    B355451
  1. Attach the guide and claw to install the lower No. 2 steering wheel cover.



20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



21. CHECK SRS WARNING LIGHT
(Click here)


22. CUSTOMIZE INFORMATION
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Utility / Customize Setting / Tilt & Telescopic.

  1. Turn the auto away/return function ON.