Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)

STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column) > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering column (Click here).



1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    B166432
  1. Using a screwdriver, detach the 2 claws and remove the steering wheel cover.

    HINT:
    Tape the screwdriver tip before use.



4. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    B166433
  1. Using a screwdriver, detach the 2 claws and remove the steering wheel cover.

    HINT:
    Tape the screwdriver tip before use.



5. REMOVE STEERING PAD


    C180934
  1. Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.

  1. Pull the steering pad toward you.



    B166581
  1. Using a thin-bladed screwdriver, release the locking button.

  1. Using a thin-bladed screwdriver, disconnect the 2 connectors.

  1. Disconnect the horn connector.



6. REMOVE STEERING WHEEL ASSEMBLY


    C180956
  1. Detach the cruise control main wire harness clamp from the steering wheel side.

  1. Disconnect the steering pad switch connector and cruise control main switch connector from the spiral cable.

  1. Remove the steering wheel set nut.



    C180950E01
  1. Put matchmarks on the steering wheel and main shaft.

  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05011)



7. REMOVE LOWER STEERING COLUMN COVER


C181134
  1. Remove the 2 screws.

  1. Detach the 2 claws to remove the lower steering column cover.



8. REMOVE UPPER STEERING COLUMN COVER


    C159215
  1. Detach the 4 clips.

  1. Detach the claw to remove the upper steering column cover.



9. REMOVE COMBINATION SWITCH


C180951
  1. Disconnect the all connectors from the turn signal switch with spiral cable.



    C159216
  1. Using pliers, grip the claws of the clamp and remove the turn signal switch with spiral cable from the steering column.



10. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



11. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



12. REMOVE INSTRUMENT SIDE PANEL LH


    B226739
  1. Using a moulding remover, detach the 7 claws and remove the side panel.



13. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B192511
  1. Detach the 3 claws.

  1. Disconnect the hood lock control cable and remove the hood lock control lever sub-assembly.



14. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


B229064
  1. Remove the 2 <A> bolts.

  1. Detach the 9 clips and claw.



    B163883
  1. Detach the 2 claws and remove the sensor.

  1. Remove the finish panel and then disconnect the connectors.



15. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY


    B225997
  1. Remove the 4 bolts and remove the instrument panel airbag.

  1. Detach the 2 claws and disconnect the DLC3.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



16. REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY


C154523
  1. Remove the bolt and air duct.



17. REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY


    C155149
  1. Remove the 3 bolts and nut.



    C154524E01
  1. Put matchmarks on the steering intermediate shaft and the steering column.

  1. Remove the bolt and steering intermediate shaft from the steering column.



    C155150E01
  1. Put matchmarks on the No. 2 steering intermediate shaft and steering intermediate shaft.

  1. Remove the bolt.

  1. Separate the steering intermediate shaft from the No. 2 steering intermediate shaft.



18. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


C155151E01
  1. Put matchmarks on the No. 2 steering intermediate shaft and power steering gear.

  1. Remove the bolt and No. 2 steering intermediate shaft from the power steering gear.



19. REMOVE STEERING COLUMN ASSEMBLY
  1. Disconnect the connectors and disengage the wire harness clamps from the steering column assembly.



    C180952E01
  1. Remove the bolt and 2 nuts. Then remove the steering column from the instrument panel reinforcement.