STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column) > REMOVAL |
| 1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE LOWER NO. 3 STEERING WHEEL COVER |
![]() |
Using a screwdriver, detach the claw and guide and remove the lower No. 3 steering wheel cover.
| *1 | Protective Tape |
| 4. REMOVE LOWER NO. 2 STEERING WHEEL COVER |
![]() |
Using a screwdriver, detach the claw and guide and remove the lower No. 2 steering wheel cover.
| *1 | Protective Tape |
| 5. REMOVE STEERING PAD |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
![]() |
Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.
Pull the steering pad toward you.
![]() |
Disconnect the horn connector from the steering pad.
Using a screwdriver, release the 2 airbag connector locks.
| *1 | Protective Tape |
Disconnect the 2 airbag connectors to remove the steering pad as shown in the illustration.
| 6. REMOVE STEERING WHEEL ASSEMBLY |
![]() |
Disconnect the 2 connectors from the spiral cable.
Remove the steering wheel set nut.
![]() |
Put matchmarks on the steering wheel and main shaft.
| *a | Matchmark |
| *b | Hold |
| *c | Turn |
Using SST, remove the steering wheel.
| 7. REMOVE LOWER STEERING COLUMN COVER |
![]() |
Remove the 2 screws.
Detach the 2 claws to remove the lower steering column cover.
| 8. REMOVE UPPER STEERING COLUMN COVER |
Detach the 4 clips.
![]() |
Detach the claw to remove the upper steering column cover.
| 9. REMOVE COMBINATION SWITCH |
![]() |
Disconnect the all connectors from the turn signal switch with spiral cable.
![]() |
Using pliers, grip the claws of the clamp and remove the turn signal switch with spiral cable from the steering column.
| 10. REMOVE FRONT DOOR SCUFF PLATE LH |
| 11. REMOVE COWL SIDE TRIM BOARD LH |
| 12. REMOVE INSTRUMENT SIDE PANEL LH |
![]() |
Using a moulding remover, detach the 7 claws and remove the side panel.
| 13. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Detach the 3 claws.
Disconnect the hood lock control cable and remove the hood lock control lever sub-assembly.
| 14. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH |
![]() |
Remove the 2 <A> bolts.
Detach the 9 clips and claw.
![]() |
Detach the 2 claws and remove the sensor.
Remove the finish panel and then disconnect the connectors.
| 15. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY |
![]() |
Remove the 4 bolts and remove the instrument panel airbag.
Detach the 2 claws and disconnect the DLC3.
Disconnect the connector.
| 16. REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY |
![]() |
Remove the bolt and air duct.
| 17. REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Remove the 3 bolts and nut.
![]() |
Put matchmarks on the steering intermediate shaft and the steering column.
| *a | Matchmark |
Remove the bolt and steering intermediate shaft from the steering column.
![]() |
Put matchmarks on the No. 2 steering intermediate shaft and steering intermediate shaft.
| *a | Matchmark |
Remove the bolt.
Separate the steering intermediate shaft from the No. 2 steering intermediate shaft.
| 18. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
![]() |
Put matchmarks on the No. 2 steering intermediate shaft and power steering gear.
| *a | Matchmark |
Remove the bolt and No. 2 steering intermediate shaft from the power steering gear.
| 19. REMOVE STEERING COLUMN ASSEMBLY |
Disconnect the connectors and disengage the wire harness clamps from the steering column assembly.
![]() |
Remove the bolt and 2 nuts. Then remove the steering column from the instrument panel reinforcement.