Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1445/45    Passenger Side Cool Air Bypass Damper Control

for Preparation Click here


DESCRIPTION

The damper servo sub-assembly (cool air bypass damper servo motor) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal, reverse) based on the signals to move the cool air bypass damper to any position. As a result, when the air conditioning system is operating, the temperature of the air blowing toward the head area is controlled.

HINT:
  1. Although the intelligent tester title says "Passenger Side", there is only one cool air bypass servo motor on this vehicle.
  2. Confirm that no mechanical problem is present because this diagnostic trouble code can be stored when either a damper link or damper is mechanically locked.


DTC Code
DTC Detection Condition
Trouble Area
B1445/45
The cool air bypass damper servo motor position does not change even if the air conditioning amplifier assembly operates the cool air bypass damper servo motor.
  1. Damper servo sub-assembly (Cool air bypass damper servo motor)
  2. Air conditioning harness assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM


E180810E11


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (COOL AIR BYPASS DAMPER SERVO MOTOR)
  1. Use the Data List to check if the servo motor is functioning properly.

    Air Conditioner 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    Cool Air Bypass Pulse
    Cool air bypass damper servo motor
    Min.: 0
    Max.: 255
    -

    OK:
    The display is as specified in the normal condition.

  1. Visually inspect the cool air bypass damper servo motor.

    1. Visually inspect whether the cool air bypass damper servo motor operates.

      OK:
      The cool air bypass damper servo motor operates.

      Result 
      Result
      Proceed to
      The Data List value changes and the cool air bypass damper servo motor operates (When troubleshooting according to the DTC output)
      A
      The Data List value changes and the cool air bypass damper servo motor operates (When troubleshooting according to Problem Symptoms Table)
      B
      The Data List value does not change and the cool air bypass damper servo motor does not operate
      C
      The Data List value changes, but the cool air bypass damper servo motor does not operate
      D



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

D
Go to step 3
A


2.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1445/45 is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK DAMPER SERVO SUB-ASSEMBLY (COOL AIR BYPASS DAMPER SERVO MOTOR)
  1. Replace the damper servo sub-assembly (cool air bypass damper servo motor) (Click here).

    HINT:
    Since the damper servo motor cannot be inspected while it is removed from the vehicle, replace the damper servo motor with a new one and check that the condition returns to normal.

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1445/45 is not output.



NG
Go to step 4
OK

END (DAMPER SERVO SUB-ASSEMBLY [COOL AIR BYPASS DAMPER SERVO MOTOR] IS FAULTY) 

4.CHECK AIR CONDITIONING HARNESS ASSEMBLY
  1. Replace the air conditioning harness assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1445/45 is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

END (AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)