Home › Steering › STEERING COLUMN › STEERING WHEEL

STEERING WHEEL > INSTALLATION

for Preparation Click here



1. INSTALL STEERING WHEEL PAD ATTACHING SCREW
  1. Set the 2 steering wheel pad attaching screws.



2. INSTALL CRUISE CONTROL MAIN SWITCH
  1. Install the cruise control main switch with the 2 screws.

  1. Install the wire harness.



3. INSTALL NO. 1 STEERING WHEEL ORNAMENT (w/o Steering Pad Switch)
  1. Attach the 3 guide pins and claw to install the switch with the 2 screws.



4. INSTALL NO. 2 STEERING WHEEL ORNAMENT (w/o Steering Pad Switch)
  1. Attach the 3 guide pins and claw to install the switch with the 2 screws.



5. INSTALL STEERING PAD SWITCH ASSEMBLY (w/ Steering Pad Switch)
  1. Attach the 6 guide pins and 2 claws to install the steering pad switch assembly with the 4 screws.



6. INSTALL STEERING PAD SWITCH LH (w/ Steering Pad Switch)

HINT:
Refer to "Install Steering pad switch assembly".



7. ADJUST SPIRAL CABLE


    B166449
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Rotate the spiral cable with steering sensor counterclockwise slowly by hand until it feels firm.

    NOTICE:
    Do not turn the spiral cable with steering sensor by the airbag wire harness.



    B166450
  1. Rotate the spiral cable with steering sensor clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable with spiral sensor by the airbag wire harness.

    HINT:
    The spiral cable with steering sensor will rotate approximately 2.5 turns to both the left and right from the center.



8. INSTALL STEERING WHEEL ASSEMBLY


    C290041E01
  1. Align the matchmarks on the steering wheel and steering main shaft.
    Text in Illustration 
    *a
    Matchmark

  1. Install the steering wheel set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



9. INSTALL STEERING PAD
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Support the steering pad with one hand.



    B354950
  1. Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.

  1. Push in the 2 connector locks to install the 2 airbag connectors.

  1. Connect the horn connector to the steering pad.

  1. Install the steering pad.



    B354952
  1. Using a T30 "TORX" socket wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



10. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    B355450
  1. Attach the guide and claw to install the lower No. 3 steering wheel cover.



11. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    B355451
  1. Attach the guide and claw to install the lower No. 2 steering wheel cover.



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



13. INSPECT STEERING PAD
  1. With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
    Cuts, minute cracks or marked discoloration on the top surface or in the grooved portion of the steering pad.

  1. Make sure that the horn sounds.
    If the horn does not sound, inspect the horn system.



14. CHECK SRS WARNING LIGHT
(Click here)