Home › Steering › STEERING COLUMN › STEERING WHEEL

STEERING WHEEL > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    B355134E01
  1. Using a screwdriver, detach the claw and guide and remove the lower No. 3 steering wheel cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape



3. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    B355135E01
  1. Using a screwdriver, detach the claw and guide and remove the lower No. 2 steering wheel cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape



4. REMOVE STEERING PAD

CAUTION:
When storing the steering pad, keep the airbag deployment side facing upward.

  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    NOTICE:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B354951
  1. Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.

  1. Pull the steering pad toward you.



    B354949E01
  1. Disconnect the horn connector from the steering pad.

  1. Using a screwdriver, release the 2 airbag connector locks.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. Disconnect the 2 airbag connectors to remove the steering pad as shown in the illustration.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.



5. REMOVE STEERING WHEEL ASSEMBLY


    C290102
  1. Disconnect the 2 connectors from the spiral cable.

  1. Remove the steering wheel set nut.



    C290035E01
  1. Put matchmarks on the steering wheel and main shaft.
    Text in Illustration 
    *a
    Matchmark
    *b
    Hold
    *c
    Turn

  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05011)



6. REMOVE NO. 2 STEERING WHEEL ORNAMENT (w/o Steering Pad Switch)


    C290053
  1. Remove the 2 screws.

  1. Detach the 3 guide pins and claw, and remove the No. 2 steering wheel ornament.



7. REMOVE NO. 1 STEERING WHEEL ORNAMENT (w/o Steering Pad Switch)


    C290054
  1. Remove the 2 screws.

  1. Detach the 3 guide pins and claw, and remove the No. 1 steering wheel ornament.



8. REMOVE STEERING PAD SWITCH ASSEMBLY (w/ Steering Pad Switch)


    C290103
  1. Remove the 4 screws.

  1. Detach the 6 guide pins and 2 claws, and remove the steering pad switch assembly.



9. REMOVE CRUISE CONTROL MAIN SWITCH
  1. Disconnect the connector and remove the harness from cruise control main switch.



    C290038
  1. Remove the 2 screws and remove the cruise control main switch.



10. REMOVE STEERING WHEEL PAD ATTACHING SCREW


    C290039
  1. Remove the 2 steering wheel pad attaching screws.