Home › Engine / Hybrid System › 3UR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > INSTALLATION

for Preparation Click here



1. REMOVE ENGINE STAND


    A163784E01
  1. Install the 2 engine hangers with the 2 bolts as shown in the illustration.

    HINT:
    Item
    Part No.
    Engine hanger
    12281-38030, 12281-38060
    Bolt
    90119-14120, 90119-A0166

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Attach an engine sling device and hang the engine with a chain block.

  1. Remove the bolts and engine assembly from the engine stand.



2. INSTALL ENGINE ASSEMBLY
  1. Slowly lower the engine assembly into the engine compartment.

    NOTICE:
    Make sure that the engine is clear of all wiring and hoses.

  1. Attach the engine mounting insulators to the vehicle.



    A163780E01
  1. Install the 4 engine mounting insulator bolts.

    Torque:
    79 N*m{ 806 kgf*cm , 58 ft.*lbf }

  1. Remove the 2 bolts and 2 engine hangers.



3. INSTALL OIL COOLER TUBE
  1. Install the oil cooler tube with the bolt.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



4. INSTALL NO. 1 WATER BY-PASS PIPE


    A183283
  1. Connect the hose and install the water by-pass pipe with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



5. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    A163778E01
  1. Using SST, hold the crankshaft.

    SST
    09213-70011  
    09330-00021  

  1. Install the crankshaft angle sensor plate, drive gear and rear drive plate spacer to the crankshaft.



    A163779E01
  1. Install and uniformly tighten 10 new bolts in the sequence shown in the illustration.

    Torque:
    30 N*m{ 301 kgf*cm , 22 ft.*lbf }

    NOTICE:
    1. Do not reuse the flywheel installation bolts.
    2. Do not strike or damage the flywheel installation bolts. Be sure to handle them carefully.



    A149106E01
  1. Mark the upside of each flywheel installation bolt with paint.

  1. Tighten the flywheel installation bolts another 90° as shown.

  1. Check that the painted marks are now at a 90° angle to the upside.



6. INSTALL EXHAUST MANIFOLD
  1. Install the exhaust manifold (Click here).



7. INSTALL GENERATOR ASSEMBLY
  1. Install the generator assembly (Click here).



8. INSTALL COOLER COMPRESSOR ASSEMBLY


    A163332E01
  1. Install the cooler compressor with the 2 stud bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the 2 bolts and 2 nuts.
    Tighten the bolts and nuts in the order shown in the illustration to install the cooler compressor.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



9. CONNECT NO. 2 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)


A183220E01
  1. Connect the No. 2 air injection hose.

  1. Attach the wire harness clamp.

  1. Connect the air pump connector.



10. CONNECT NO. 3 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)


A183218E01
  1. Connect the No. 3 air injection hose.



11. INSTALL ENGINE WIRE


    A163790
  1. Connect the 2 connectors and 2 clips to the engine room junction block.

  1. Install the engine wire with the nut. Then connect the 2 clips.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. w/ Secondary Air Injection System:
    Connect the 4 air injection control driver connectors.

  1. Install the ground wire with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the cable to the positive (+) battery terminal.

  1. Install the wire to the positive (+) battery cable with the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A163791
  1. w/ Secondary Air Injection System:
    Connect the 2 air injection system hoses.

  1. Install the ground wire with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. w/ Secondary Air Injection System:
    Connect the 2 air pump connectors and install the connector bracket with the nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



    A160782E01
  1. Connect the 4 connectors to the connector holder block.

  1. Connect the heater hoses.



12. INSTALL ECM


    A183281
  1. Connect the ECM connector and clamp.

    HINT:
    Refer to the following procedures to connect the ECM connector .



13. CONNECT FUEL MAIN AND RETURN HOSE


    A160798
  1. Connect the fuel main and return hoses (Click here).

  1. Install the fuel pipe clamp.



14. CONNECT PURGE LINE HOSE


    A183280
  1. Connect the purge line hose.



15. CONNECT VACUUM HOSE ASSEMBLY


    A183279
  1. Connect the union to check valve hose.



16. CONNECT OUTLET HEATER WATER HOSE C


    A183229E01
  1. Connect the outlet heater water hose to the No. 1 water by-pass pipe.

    HINT:
    Install the hose so that the direction of the hose clamp is as indicated in the illustration.



17. CONNECT INLET HEATER WATER HOSE C


    A183231E01
  1. Connect the inlet heater water hose to the water by-pass pipe.

    HINT:
    Install the hose so that the direction of the hose clamp is as indicated in the illustration.



18. INSTALL AIR CLEANER HOSE ASSEMBLY


A198568E01
  1. Connect the air cleaner hose and tighten clamp.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the No. 2 ventilation hose with the clamp.

    HINT:
    Install the hose so that the direction of the hose clamp is as indicated in the illustration.

  1. Connect the vacuum hose.



19. INSTALL AIR CLEANER ASSEMBLY


    A183246E01
  1. Attach grommet to air cleaner before mounting the air cleaner.

  1. Insert the air cleaner into the fender apron hole, and fully insert pin to grommet.



    A183242
  1. Install the air cleaner with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector and install the clamp and wire harness.

  1. Connect the air cleaner hose and tighten the clamp.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



20. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
  1. for 4WD:
    Install the transmission assembly (Click here).

  1. for 2WD:
    Install the transmission assembly (Click here).



21. INSTALL RADIATOR ASSEMBLY
  1. Install the radiator assembly (Click here).



22. ADD ENGINE OIL


    A221087E01
  1. Add fresh oil.

    Standard Oil Grade:
    Oil Grade
    Oil Viscosity (SAE)
    API grade SL or SM multigrade engine oil
    1. 15W-40
    2. 20W-50
    API grade SL "Energy-Conserving", SM "Energy-Conserving" or ILSAC multigrade engine oil
    1. 5W-30
    2. 10W-30
    (5W-30 is the best choice for fuel economy and good starting in cold weather.)

    Standard Oil Capacity (for Type A):
    Item
    Specified Condition
    Drain and refill without oil filter change
    6.6 liters (7.0 US qts., 5.8 Imp. qts.)
    Drain and refill with oil filter change
    7.0 liters (7.4 US qts., 6.2 Imp. qts.)
    Dry fill
    8.4 liters (8.9 US qts., 7.4 Imp. qts.)

    Standard Oil Capacity (for Type B):
    Item
    Specified Condition
    Drain and refill without oil filter change
    7.1 liters (7.4 US qts, 6.2 Imp. qts)
    Drain and refill with oil filter change
    7.5 liters (7.9 US qts, 6.6 Imp. qts)
    Dry fill
    9.3 liters (9.8 US qts, 8.2 Imp. qts)

  1. Install the oil filler cap.



23. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard Capacity:
    14.6 liters (15.4 US qts., 12.8 Imp. qts.)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. Please contact your Toyota dealer for further details.



    A151850E05
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E01
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



25. INSPECT FOR OIL LEAK


26. INSPECT FOR COOLANT LEAK


A161766E01

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



27. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


28. INSPECT FOR FUEL LEAK
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

    NOTICE:
    Do not start the engine.

  1. Turn the intelligent tester main switch ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.



29. INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY


    A183287
  1. Install the outer panel with the 7 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the 2 washer hoses.



30. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
  1. Install the windshield wiper motor (Click here).



31. INSTALL HOOD SUB-ASSEMBLY


    A160840
  1. Install the hood with the 4 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Attach the lower part of the 2 hood supports to the hood support bolt ball joints.

    NOTICE:
    Install the hood support while supporting the hood by hand.

  1. Attach the hood support clips.

    NOTICE:
    Check that the hood support is engaged in the ball joint and that it cannot be pulled out.



32. ADJUST HOOD SUB-ASSEMBLY


    B192131
  1. Loosen the 4 hood side hinge bolts.

  1. Move the hood to adjust the clearance to within the standard range.

  1. Tighten the 4 hood side hinge bolts after the adjustment.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    B192132
  1. Adjust the height of the hood front end by turning the cushion rubber.

    HINT:
    The cushion rubber can be raised and lowered by turning it.



  1. Adjust the hood lock.



      B220937
    1. Remove the hood lock nut cap.



    2. B220936
    3. Loosen the 2 bolts and nut.



    4. B166030
    5. Adjust the hood lock position so that the striker can enter it smoothly.



    6. B220936
    7. Tighten the 2 bolts and nut after the adjustment.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



33. INSPECT IGNITION TIMING
  1. Warm up and stop the engine.

    1. Allow the engine to warm up to a normal operating temperature.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Start the engine and idle it.

    3. Turn the intelligent tester main switch on.

    4. Enter the following menus: Select: Powertrain / Engine and ECT / Data List / IGN Advance.

      Standard ignition timing:
      8 to 12° BTDC @ idle (transmission in neutral and A/C switch off)

      HINT:
      Refer to the intelligent tester operator manual for further details.

    5. Disconnect the intelligent tester from the DLC3.



    A160842E01
  1. When not using the intelligent tester:

    1. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

      NOTICE:
      Use a timing light that detects primary signals.



    2. H102392E79
    3. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
      2. Switch off all accessories and the A/C before connecting the terminals.



    4. A160843E01
    5. Using the timing light, check the ignition timing.

      Standard ignition timing:
      8 to 12° BTDC @ idle (transmission in neutral and A/C switch off)

    6. Remove SST from the DLC3.

    7. Check the ignition timing.

      Standard ignition timing:
      7 to 24° BTDC @ idle (transmission in neutral and A/C switch off)

    8. Disconnect the timing light from the engine.



34. INSPECT ENGINE IDLE SPEED
  1. Warm up and stop the engine.

    1. Allow the engine to warm up to a normal operating temperature.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

      NOTICE:
      Switch off all accessories and the A/C before connecting the intelligent tester.

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Turn the intelligent tester main switch on.

    4. Enter the following menus: Select: Powertrain / Engine and ECT / Data List / Engine Speed.

      Standard idle speed:
      650 to 750 rpm (transmission in neutral and A/C switch off)

      HINT:
      Refer to the intelligent tester operator manual for further details.

      If the idle speed is not as specified, check the air intake system.

    5. Disconnect the intelligent tester from the DLC3.



    H102392E88
  1. When not using the intelligent tester:

    1. Using SST, connect the tachometer probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

      NOTICE:
      1. Confirm the terminal number before connecting the probe. Connecting the probe to the wrong terminal can damage the engine.
      2. Switch off all accessories and the A/C before connecting the probe.

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Check the idle speed.

      Standard idle speed:
      650 to 750 rpm (transmission in neutral and A/C switch off)

      If the idle speed is not as specified, check the air intake system.

    4. Disconnect the tachometer from the DLC3.



35. INSPECT CO/HC

HINT:
This check is used only to determine whether or not the idle CO/ HC complies with regulations.

  1. Start the engine.

  1. Keep the engine speed at 2500 rpm for approximately 180 seconds.



    A185322E01
  1. Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.

  1. Immediately check CO/HC concentration at idle and/or 2500 rpm.

    HINT:
    When performing the 2 mode (2500 rpm and idle) test, follow the measurement order prescribed by the applicable local regulations.

  1. If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.

    1. Check the A/F sensor (Click here) and heated oxygen sensor (Click here) operation.

    2. See the table below for possible causes, and then inspect and correct the applicable causes if necessary.

      CO
      HC
      Symptom
      Cause
      Normal
      High
      Rough idle
      1. Faulty ignitions:
        1. Incorrect timing
        2. Plugs (contaminated, shorted or gaps are defective)
      2. Incorrect valve clearance
      3. Leaky intake and exhaust valves
      4. Leaky cylinder
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hose
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective ECT sensor
        3. Faulty ECM
        4. Faulty injectors
        5. Faulty throttle position sensor
        6. Faulty MAF meter



36. INSPECT FOR ENGINE OIL LEVEL
  1. Warm up the engine, and then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.



37. INSPECT FOR ENGINE COOLANT LEVEL


    A151850E05
  1. Check that the engine coolant level is between the LOW and FULL lines when the engine is cold.
    If the engine coolant is low, check for leaks and add "TOYOTA Super Long Life Coolant" or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology to the FULL line.

    NOTICE:
    Do not substitute plain water for engine coolant.



38. INSPECT SRS WARNING LIGHT
(Click here)