Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR DRIVE UNIT

POWER BACK DOOR DRIVE UNIT > REMOVAL

for Preparation Click here



1. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    B190118
  1. Raise the handle, detach the 4 guides and remove the No. 2 deck board.



2. REMOVE LUGGAGE COMPARTMENT TRIM BOX


    B194633
  1. Remove the 4 caps.



    B190116
  1. Remove the 4 bolts and luggage compartment trim box.



3. REMOVE ROPE HOOK ASSEMBLY


    B191405
  1. Remove the bolt and rope hook.

    HINT:
    Use the same procedure for both sides.



4. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY


    B190117
  1. Detach the 5 clips and remove the No. 1 deck board.



5. REMOVE DECK BOARD REINFORCEMENT SUB-ASSEMBLY


    B190120
  1. Remove the 4 bolts and deck board reinforcement.



6. REMOVE DECK BOARD BRACKET


    B190119
  1. Remove the 2 bolts and deck board bracket.



7. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Manual Seat)
  1. Remove the rear No. 2 seat assembly LH (Click here).



8. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Power Seat)
  1. Remove the rear No. 2 seat assembly LH (Click here).



9. REMOVE REAR SEAT CUSHION HINGE LOWER COVER LH

HINT:
Use the same procedure for both sides.



10. REMOVE REAR FLOOR STEP NO. 1 COVER


    B191403E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



11. REMOVE REAR FLOOR STEP NO. 2 COVER


    B193052E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



12. REMOVE REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



13. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



14. REMOVE ROPE HOOK ASSEMBLY

HINT:
Use the same procedure for both sides.



    B190140E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.



    B190141
  1. Remove the bolt and the rope hook.



15. REMOVE REAR FLOOR MAT SUPPORT PLATE


    B190142
  1. Detach the 5 clips and 4 claws, and remove the rear floor mat support plate.



16. REMOVE QUARTER TRIM PANEL ASSEMBLY LH


    B193920
  1. Detach the 3 claws and remove the outer lap belt anchor cover.



    B191818
  1. Remove the bolt and outer lap belt anchor.



    B191816
  1. Remove the bolt and outer lap belt anchor.



    B191817E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Detach the 11 clips.



  1. Disconnect the connector and remove the quarter trim panel.


    B222458



17. REMOVE QUARTER TRIM PANEL ASSEMBLY LH (for Power Seat)


    B193920
  1. Detach the 3 claws and remove the outer lap belt anchor cover.



    B191818
  1. Remove the bolt and outer lap belt anchor.



    B191816
  1. Remove the bolt and outer lap belt anchor.



    B191817E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Detach the 2 clamps and remove the wire harness.

  1. Detach the 11 clips and 2 clamps.



  1. Disconnect the 3 connectors and remove the quarter trim panel.


    B222460



18. REMOVE REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY LH


    B191819E01
  1. Using a screwdriver, detach the claw and remove the cover.



    B191798
  1. Remove the bolt.

  1. Detach the 5 clips.

  1. Disconnect the connector.

  1. Pass the rear seat outer belt floor anchor through the rear window No. 2 side garnish, and remove the rear window No. 2 side garnish.



19. REMOVE POWER BACK DOOR ROD


    B194506E01
  1. Using a screwdriver with its tip wrapped in protective tape, remove the 2 stop rings and power back door rod.



20. REMOVE POWER BACK DOOR UNIT


    B192141
  1. Disconnect the connector.

  1. Remove the 4 bolts and remove the power back door unit.