Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR CLOSER SYSTEM

BACK DOOR CLOSER SYSTEM > Back Door Closer does not Operate

for Preparation Click here


DESCRIPTION

When the back door closer does not operate, one of the following may be the cause: 1) improper fit of back door, or a foreign object is stuck in back door, or 2) initialization of the power back door ECU, or 3) power back door ECU power source circuit malfunction, or 4) back door lock circuit malfunction, or 5) power back door ECU malfunction.

WIRING DIAGRAM


E182426E01


INSPECTION PROCEDURE

1.CHECK BACK DOOR LOCK FUNCTION
  1. Check if the back door is fully closed by hand.



NG
IMPROPER FIT OF BACK DOOR, OR A FOREIGN OBJECT IS STUCK IN BACK DOOR
OK


2.INITIALIZE POWER BACK DOOR ECU
  1. Check that the power back door drive unit (power back door ECU) can be initialized (Click here).


NEXT


3.CHECK BACK DOOR CLOSER SYSTEM
  1. Check that the back door closer system operates normally.

    OK:
    Back door closer system operates normally.



NG
Go to step 4
OK

END 

4.CHECK DTC OUTPUT
  1. Check for the DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    B2250 is output
    B
    B2251 is output
    C



B
GO TO DTC CHART (Click here)

C
GO TO DTC CHART (Click here)
A


5.INSPECT FUSE (ECU-IG NO. 2, ECU-B1, PBD)
E160630E14
  1. Remove the ECU-IG NO. 2, ECU-B1, and PBD fuses.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-IG NO. 2 fuse
    Always
    Below 1 Ω
    ECU-B1 fuse
    Always
    Below 1 Ω
    PBD fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


6.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B220586E01
  1. Disconnect the O30 power back door ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O30-8 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    O30-10 (ECUB) - Body ground
    Always
    11 to 14 V
    O30-12 (B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (BODY GROUND)
B220586E02
  1. Disconnect the O30 power back door ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O30-11 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT BACK DOOR LOCK

B191744E03

  1. Remove the back door lock (Click here).

  1. Apply battery voltage and check the operation of the door lock motor.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1 (ACT+)
    Battery negative (-) → Terminal 2 (ACT-)
    Latch turns to open-latch position
    Battery positive (+) → Terminal 2 (ACT-)
    Battery negative (-) → Terminal 1 (ACT+)
    Latch turns to full-latch position

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Latch Switch:
    Tester Connection
    Condition
    Specified Condition
    5 (CLS) - 3 (E)
    Door lock latch position is open-latch
    Below 1 Ω
    5 (CLS) - 3 (E)
    Door lock latch position is over-latch
    Below 1 Ω
    5 (CLS) - 3 (E)
    Door lock latch position is full-latch
    10 kΩ or higher
    5 (CLS) - 3 (E)
    Door lock latch position is half-latch
    10 kΩ or higher
    Back Door Courtesy Light Switch:
    Tester Connection
    Condition
    Specified Condition
    6 (S) - 3 (E)
    Door lock latch position is open-latch
    Below 1 Ω
    6 (S) - 3 (E)
    Door lock latch position is over-latch
    10 kΩ or higher
    6 (S) - 3 (E)
    Door lock latch position is full-latch
    10 kΩ or higher
    6 (S) - 3 (E)
    Door lock latch position is half-latch
    Below 1 Ω



NG
REPLACE BACK DOOR LOCK (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK - POWER BACK DOOR ECU AND BACK DOOR ECU)


    B191749E02
  1. Disconnect the V5 door lock connector.

  1. Disconnect the O30 ECU connectors.

  1. Disconnect the V2 and V3 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V5-2 (ACT-) - O30-2 (DC+)
    Always
    Below 1 Ω
    V5-1 (ACT+) - O30-1 (DC-)
    Always
    Below 1 Ω
    V5-5 (CLS) - O30-22 (HAF)
    Always
    Below 1 Ω
    V5-6 (S) - V3-10 (BDCY)
    Always
    Below 1 Ω
    V5-3 (E) - V3-20 (CTYE)
    Always
    Below 1 Ω
    V2-17 (OCTY) - O30-20 (FULL)
    Always
    Below 1 Ω
    O30-2 (DC+) - Body ground
    Always
    10 kΩ or higher
    O30-1 (DC-) - Body ground
    Always
    10 kΩ or higher
    O30-22 (HAF) - Body ground
    Always
    10 kΩ or higher
    O30-20 (FUL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
  1. Temporarily replace the power back door drive unit (power back door ECU) with a new or normally functioning one (Click here).


NEXT


11.CHECK BACK DOOR CLOSER SYSTEM (OPERATION)
  1. Check that the back door closer operates normally.

    OK:
    It operates normally.



NG
REPLACE BACK DOOR ECU (Click here)
OK

END (POWER BACK DOOR UNIT (POWER BACK DOOR ECU) DEFECTIVE)