Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR CLOSER SYSTEM

BACK DOOR CLOSER SYSTEM > Back Door cannot be Opened

for Preparation Click here


DESCRIPTION

When the back door cannot be opened, one of the following may be the cause: 1) power back door ECU malfunction, 2) back door lock malfunction, 3) back door open switch malfunction, 4) main body ECU malfunction, 5) back door ECU malfunction, 6) power source circuit malfunction, or 7) position SW in prohibit condition. In the case that a fault is detected at the position switch, the back door stops functioning when the door position is full-latch (system prohibits opening of the door). Thereafter, the system prohibits back door operation until it detects a power reset of the ECU.

HINT:
Since the power back door system has functions that use CAN and LIN communication, first confirm that there is no malfunction in the communication system by inspecting the CAN and LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


WIRING DIAGRAM


E182431E01


INSPECTION PROCEDURE

1.INSPECT FUSES (ECU-IG NO.2, ECU-B1, PBD)
E160630E15
  1. Remove the ECU- IG NO. 2, ECU-B1 and PBD fuses.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-IG NO. 2 fuse
    Always
    Below 1 Ω
    ECU-B1 fuse
    Always
    Below 1 Ω
    PBD fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B220586E01
  1. Disconnect the O30 power back door ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O30-8 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    O30-10 (ECUB) - Body ground
    Always
    11 to 14 V
    O30-12 (B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR ECU - BODY GROUND)
B220586E02
  1. Disconnect the O30 power back door ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O30-11 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.READ VALUE USING INTELLIGENT TESTER (BACK DOOR OPEN HANDLE SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Back Door P/W / Data List /

  1. According to the display on the intelligent tester, read the Data List.

    Back Door P/W (Back Door ECU) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Open Handle SW
    Back door opener switch / ON or OFF
    ON: Back door opener switch is pushed
    OFF: Back door opener switch is not pushed
    -

    OK:
    The back door opener switch functions as specified in the normal condition.



NG
Go to step 11
OK


5.INSPECT BACK DOOR LOCK

B191744E04

  1. Remove the back door lock (Click here).

  1. Apply battery voltage and check operation of the door lock motor.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1 (ACT+)
    Battery negative (-) → Terminal 2 (ACT-)
    Latch turns to open-latch position
    Battery positive (+) → Terminal 2 (ACT-)
    Battery negative (-) → Terminal 1 (ACT+)
    Latch turns to full-latch position

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Latch Switch
    Tester Connection
    Condition
    Specified Condition
    5 (CLS) - 3 (E)
    Door lock latch position is open-latch
    Below 1 Ω
    5 (CLS) - 3 (E)
    Door lock latch position is over-latch
    Below 1 Ω
    5 (CLS) - 3 (E)
    Door lock latch position is full-latch
    10 kΩ or higher
    5 (CLS) - 3 (E)
    Door lock latch position is half-latch
    10 kΩ or higher
    Sector Switch:
    Tester Connection
    Condition
    Specified Condition
    4 (FSW) - 3 (E)
    Door lock latch position is open-latch
    Below 1 Ω
    4 (FSW) - 3 (E)
    Door lock latch position is over-latch
    10 kΩ or higher
    4 (FSW) - 3 (E)
    Door lock latch position is full-latch
    Below 1 Ω
    4 (FSW) - 3 (E)
    Door lock latch position is half-latch
    Below 1 Ω
    Back Door Courtesy Light Switch:
    Tester Connection
    Condition
    Specified Condition
    6 (S) - 3 (E)
    Door lock latch position is open-latch
    Below 1 Ω
    6 (S) - 3 (E)
    Door lock latch position is over-latch
    10 kΩ or higher
    6 (S) - 3 (E)
    Door lock latch position is full-latch
    10 kΩ or higher
    6 (S) - 3 (E)
    Door lock latch position is half-latch
    Below 1 Ω



NG
REPLACE BACK DOOR LOCK (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK - POWER BACK DOOR ECU, BACK DOOR ECU)


    B191749E05
  1. Disconnect the V5 back door lock connector.

  1. Disconnect the O30, V2 and V3 ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V5-1 (ACT+) - O30-1 (DC-)
    Always
    Below 1 Ω
    V5-2 (ACT-) - O30-2 (DC+)
    Always
    Below 1 Ω
    V5-5 (CLS) - O30-22 (HAF)
    Always
    Below 1 Ω
    V5-4 (FSW) - O30-24 (POS)
    Always
    Below 1 Ω
    V5-6 (S) - V3-10 (BDCY)
    Always
    Below 1 Ω
    V5-3 (E) - V3-20 (CTYE)
    Always
    Below 1 Ω
    V2-17 (OCTY) - O30-20 (FUL)
    Always
    Below 1 Ω
    O30-1 (DC-) - Body ground
    Always
    10 kΩ or higher
    O30-2 (DC+) - Body ground
    Always
    10 kΩ or higher
    O30-22 (HAF) - Body ground
    Always
    10 kΩ or higher
    O30-24 (POS) - Body ground
    Always
    10 kΩ or higher
    O30-20 (FUL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE BACK DOOR ECU
  1. Temporarily replace the back door ECU with a new or normally functioning one (Click here).


NEXT


8.CHECK BACK DOOR CLOSER SYSTEM (OPERATION)
  1. Check that the back door closer operates normally.

    OK:
    It operates normally.



NG
Go to step 9
OK

END (BACK DOOR ECU DEFECTIVE) 

9.REPLACE POWER BACK DOOR UNIT (POWER BACK DOOR ECU)
  1. Temporarily replace the power back door drive unit (power back door ECU) with a new or normally functioning one (Click here).


NEXT


10.CHECK BACK DOOR CLOSER SYSTEM (OPERATION)
  1. Check that the back door closer operates normally.

    OK:
    It operates normally.



NG
REPLACE MAIN BODY ECU
OK

END (POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) DEFECTIVE) 

11.INSPECT BACK DOOR OPENER SWITCH


    B190834E01
  1. Remove the back door opener switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Free
    10 kΩ or higher
    1 - 2
    Pushed
    Below 1 Ω



NG
REPLACE BACK DOOR OPENER SWITCH
OK


12.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH - BACK DOOR ECU)


    B191750E01
  1. Disconnect the V6 switch connector.

  1. Disconnect the V3 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V6-1 - V3-15 (HSW+)
    Always
    Below 1 Ω
    V6-2 - V3-24 (HSW-)
    Always
    Below 1 Ω
    V6-1 or V3-15 (HSW+) - Body ground
    Always
    10 kΩ or higher
    V6-2 or V3-24 (HSW-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK DOOR ECU