Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM

POWER BACK DOOR SYSTEM > Power Back Door cannot be Opened or Closed Using the Power Back Door Switch

for Preparation Click here


DESCRIPTION

When the power back door cannot be opened or closed using the power back door control switch, one of the following may be malfunctioning: 1) back door control switch circuit, 2) power back door drive unit (power back door ECU), or 3) main body ECU.

HINT:
Since the power back door system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


WIRING DIAGRAM


B190841E01


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (BACK DOOR CONTROL SWITCH)
  1. Connect the intelligent tester to the DLC3

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Open SW
    Back door control switch / ON or OFF
    ON: Back door control switch is pushed
    OFF: Back door control switch is not pushed
    -

    OK:
    The back door control switch functions as specified in the normal condition.



NG
Go to step 4
OK


2.REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
  1. Temporarily replace the power back door drive unit (power back door ECU) with a new or normally functioning one (Click here).


NEXT


3.CHECK POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
  1. Check that the power back door operates normally.

    OK:
    It operates normally.



NG
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK LH)
OK

END (REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) DEFECTIVE) 

4.INSPECT BACK DOOR CONTROL SWITCH


    B190838E03
  1. Remove the back door control switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (E) - 6 (CSW)
    Back door control switch not pushed (OFF)
    10 kΩ or higher
    3 (E) - 6 (CSW)
    Back door control switch pushed (ON)
    Below 1 Ω



NG
REPLACE POWER BACK DOOR OPENER / CLOSER SWITCH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (CONTROL SWITCH - MAIN BODY ECU AND BODY GROUND)


    B190842E01
  1. Disconnect the H70 switch connector.

  1. Disconnect the H4 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H70-6 (CSW) - H4-26 (PBDS)
    Always
    Below 1 Ω
    H70-3 (E) - Body ground
    Always
    Below 1 Ω
    H70-6 (CSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
  1. Replace the power back door drive unit (power back door ECU) (Click here).


NEXT


7.CHECK POWER BACK DOOR DRIVE UNIT
  1. Check that the power back door operates normally.

    OK:
    It operates normally.



NG
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK LH)
OK

END (REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) DEFECTIVE)