Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1447/47    Rear Air Mix Damper Control Servo Motor Circuit

for Preparation Click here


DESCRIPTION

The rear air mix damper servo sub-assembly sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the rear air mix damper to the appropriate position. This adjusts the amount of air passing through the heater core after passing the evaporator and controls the temperature of the blown air.

HINT:
Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or damper is mechanically locked.


DTC Code
DTC Detection Condition
Trouble Area
B1447/47
The rear air mix damper position does not change even if the air conditioning amplifier assembly operates the rear air mix damper servo motor.
  1. Rear air mix damper servo sub-assembly
  2. No. 2 air conditioning harness assembly
  3. Harness or connector between No. 2 air conditioning harness assembly and air conditioning amplifier assembly
  4. Air conditioning amplifier assembly

WIRING DIAGRAM


E180816E01


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (REAR AIR MIX SERVO MOTOR)
  1. Use the Data List to check if the servo motor is functioning properly.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Mix Targ Pulse (R)
    Rear air mix servo motor /
    Min.: 0, Max.: 255
    Customized value displayed
    -

    OK:
    The display is as specified in the normal condition.

  1. Visually inspect the rear air mix servo motor.

    1. Visually inspect whether the rear air mix servo motor operates.

      OK:
      The rear air mix servo motor operates.

      Result 
      Result
      Proceed to
      The Data List value changes and the rear air mix servo motor operates (When troubleshooting according to the DTC output)
      A
      The Data List value changes and the rear air mix servo motor operates (When troubleshooting according to Problem Symptoms Table)
      B
      The Data List value does not change and the rear air mix servo motor does not operate
      C
      The Data List value changes, but the rear air mix servo motor does not operate
      D



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

D
Go to step 3
A


2.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1447/47 is not output



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)


    E127593E06
  1. Disconnect the P9 No. 2 air conditioning harness assembly connector.

  1. Disconnect the H67 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P9-2 (RBUG) - H67-21 (RBUG)
    Always
    Below 1 Ω
    P9-3 (RBUS) - H67-1 (RBUS)
    Always
    Below 1 Ω
    P9-4 (RBBU) - H67-23 (RBBU)
    Always
    Below 1 Ω
    H67-21 (RBUG) - Body ground
    Always
    10 kΩ or higher
    H67-1 (RBUS) - Body ground
    Always
    10 kΩ or higher
    H67-23 (RBBU) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK REAR AIR MIX DAMPER SERVO SUB-ASSEMBLY
  1. Replace the rear air mix damper servo sub-assembly (Click here).

    HINT:
    Since the damper servo motor cannot be inspected while it is removed from the vehicle, replace the damper servo motor with a new one and check that the condition returns to normal.

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1447/47 is not output.



NG
Go to step 5
OK

END (REAR AIR MIX DAMPER SERVO SUB-ASSEMBLY IS FAULTY) 

5.REPLACE NO.2 AIR CONDITIONING HARNESS ASSEMBLY
  1. Replace the No. 2 air conditioning harness assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1447/47 is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

END (NO.2 AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)