Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1449/49    Rear Air Outlet Damper Control Servo Motor Circuit

for Preparation Click here


DESCRIPTION

The rear mode damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the rear air outlet damper to the appropriate position, which controls the air outlet modes.

HINT:
Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or damper is mechanically locked.


DTC Code
DTC Detection Condition
Trouble Area
B1449/49
The rear mode damper position does not change even if the air conditioning amplifier assembly operates the rear air outlet damper servo motor.
  1. Rear mode damper servo sub-assembly
  2. No. 2 air conditioning harness assembly
  3. Harness or connector between No. 2 air conditioning harness assembly and air conditioning amplifier assembly
  4. Air conditioning amplifier assembly

WIRING DIAGRAM


E180816E02


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (REAR AIR OUTLET SERVO MOTOR)
  1. Use the Data List to check if the servo motor is functioning properly.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Outlet Servo Pulse (R)
    Rear air outlet servo motor /
    Min.: 0
    Max.: 255
    Customized value will be displayed
    -

    OK:
    The display is as specified in the normal condition.

  1. Visually inspect the rear air outlet servo motor.

    1. Visually inspect whether the rear air outlet servo motor operates.

      OK:
      The rear air outlet servo motor operates.

      Result 
      Result
      Proceed to
      The Data List value changes and the rear air outlet servo motor operates (When troubleshooting according to the DTC output)
      A
      The Data List value changes and the rear air outlet servo motor operates (When troubleshooting according to Problem Symptoms Table)
      B
      The Data List value does not change and the rear air outlet servo motor does not operate
      C
      The Data List value changes, but the rear air outlet servo motor does not operate
      D



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

D
Go to step 4
A


2.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1449/49 is not output.



NG
REPLACE NO. 2 AIR CONDITIONING HARNESS ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)


    E127593E07
  1. Disconnect the P9 No. 2 air conditioning harness assembly connector.

  1. Disconnect the H67 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P9-2 (RBUG) - H67-21 (RBUG)
    Always
    Below 1 Ω
    P9-3 (RBUS) - H67-1 (RBUS)
    Always
    Below 1 Ω
    P9-4 (RBBU) - H67-23 (RBBU)
    Always
    Below 1 Ω
    H67-21 (RBUG) - Body ground
    Always
    10 kΩ or higher
    H67-1 (RBUS) - Body ground
    Always
    10 kΩ or higher
    H67-23 (RBBU) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK REAR MODE DAMPER SERVO SUB-ASSEMBLY
  1. Replace the rear mode damper servo sub-assembly (Click here).

    HINT:
    Since the damper servo cannot be inspected while it is removed from the vehicle, replace the damper servo with a normal one.

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1449/49 is not output.



NG
Go to step 5
OK

END (REAR MODE DAMPER SERVO SUB-ASSEMBLY IS FAULTY) 

5.CHECK AIR CONDITIONING HARNESS ASSEMBLY
  1. Replace the air conditioning harness assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1449/49 is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

END (AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)