POWER WINDOW REGULATOR MOTOR > INSTALLATION |
| 1. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY |
![]() |
Apply MP grease to the sliding and rotating areas of the regulator motor.
Using a T25 "TORX" socket wrench, install the power window regulator motor with the 3 screws.
| 2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY |
Apply MP grease to the sliding and rotating areas of the rear door window regulator sub-assembly.
![]() |
Loosely install the bolt labeled A onto the window regulator sub-assembly.
Insert the rear door window regulator sub-assembly into the door panel. Provisionally tighten bolt A to hang the rear door window regulator sub-assembly on the door panel.
Install the front door window regulator sub-assembly with the 5 bolts, and tighten the bolt labeled A.
Connect the connector.
| 3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Install the rear door glass sub-assembly onto the rear door window regulator with the 2 bolts.
| 4. INSTALL REAR DOOR WINDOW FRONT GUIDE SUB-ASSEMBLY |
![]() |
Install the rear door window guide front sub-assembly with the 2 bolts
| 5. INSTALL REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY |
![]() |
Install the rear door window frame rear lower sub-assembly with the nut and 3 bolts.
| 6. INSTALL REAR DOOR GLASS RUN |
![]() |
Install the rear door glass run.
| 7. INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP |
| 8. INSTALL REAR DOOR WINDOW FRAME REAR MOULDING |
| 9. INSTALL REAR DOOR SERVICE HOLE COVER |
![]() |
Apply butyl tape to the door panel, then install a new rear door service hole cover as shown in the illustration.
![]() |
Attach the clamps and connect the connectors.
| 10. INSTALL REAR DOOR TRIM NO. 2 BRACKET |
![]() |
Install the rear door trim No. 2 bracket with the 2 screws.
| 11. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Connect the rear door lock remote control cable and the rear door inside locking cable.
Connect the connector.
![]() |
Attach the 9 clips to install the rear door trim board sub-assembly.
![]() |
Tighten the 2 screws.
Install the rear door armrest cover.
| 12. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Attach the 4 claws to install the rear door inside handle bezel plug.
| 13. INSTALL REAR DOOR ARMREST BASE UPPER PANEL |
Connect the connector.
![]() |
Attach the 2 clips and 5 claws to install the rear door armrest base upper panel.
| 14. INSTALL REAR DOOR FRAME GARNISH |
![]() |
Attach the 6 clips to install the rear door frame garnish.
| 15. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY |
![]() |
Apply MP grease to the sliding and rotating areas of the regulator motor.
Using a T25 "TORX" socket wrench, install the front power window regulator motor with the 3 screws.
| 16. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY |
Apply MP grease to the sliding and rotating areas of the front door window regulator.
![]() |
Loosely screw bolt A onto the front door window regulator
Insert the front door window regulator into the door panel. Provisionally tighten bolt A to hang the front door window regulator on the door panel.
Install the front door window regulator with the 5 bolts, and tighten bolt A.
Connect the connector.
| 17. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY |
![]() |
Insert the door glass into the door panel by the arrows in the illustration.
![]() |
Install the front door glass onto the front door window regulator with the 2 bolts.
| 18. INSTALL FRONT DOOR GLASS RUN |
![]() |
Install the front door glass run.
| 19. INSTALL FRONT DOOR SERVICE HOLE COVER |
![]() |
Apply butyl tape to the door panel, then install a new front door service hole cover as shown in the illustration.
![]() |
Attach the clamps and connect the connectors.
| 20. INSTALL FRONT DOOR NO. 1 TRIM BRACKET |
![]() |
Install the front door No. 1 trim bracket with the 2 screws.
| 21. INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY |
| 22. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY |
| 23. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
Connect the connectors.
![]() |
Connect the front door lock remote control cable and the front door inside locking cable.
![]() |
Attach the 10 clips to install the front door trim board sub-assembly.
![]() |
Tighten the 2 screws.
Install the front door armrest cover.
| 24. INSTALL FRONT ARMREST BASE UPPER PANEL |
![]() |
Connect the connector.
Attach the 2 clips and 5 claws to install the front armrest base upper panel.
| 25. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Attach the 4 claws to install the front door inside handle bezel plug
| 26. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH |
![]() |
Connect the connector.
Attach the 3 clips to install the front door lower frame bracket garnish.
| 27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |