Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM

BLIND SPOT MONITOR SYSTEM > Main Switch Circuit

for Preparation Click here


DESCRIPTION

When the blind spot monitor main switch assembly (warning canceling switch assembly) is turned on, a signal is sent to the blind spot monitor sensor RH. The blind spot monitor system operates according to this signal.

WIRING DIAGRAM


E224414E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuse for circuits related to this system before performing the following inspection procedure.

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Blind Spot Monitor Master / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Blind Spot Monitor Master 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    BSM Main SW
    Blind spot monitor main switch assembly (warning canceling switch assembly) / OFF or ON
    ON: Blind spot monitor main switch assembly (warning canceling switch assembly) on
    OFF: Blind spot monitor main switch assembly (warning canceling switch assembly) off
    -
    Result 
    Result
    Proceed to
    The display changes as shown above when the blind spot monitor main switch assembly (warning canceling switch assembly) is operated.
    A
    The display does not change as shown above when the blind spot monitor main switch assembly (warning canceling switch assembly) is operated.
    B



B
Go to step 2
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT BLIND SPOT MONITOR MAIN SWITCH ASSEMBLY (WARNING CANCELING SWITCH ASSEMBLY)


    E224422E08
  1. Remove the blind spot monitor main switch assembly (warning canceling switch assembly) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    11 (B) - 8 (D)
    Blind spot monitor main switch is on
    Below 1 Ω
    11 (B) - 8 (D)
    Blind spot monitor main switch is off
    10 kΩ or higher



NG
REPLACE BLIND SPOT MONITOR MAIN SWITCH ASSEMBLY (WARNING CANCELING SWITCH ASSEMBLY) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BATTERY)
  1. Disconnect the H121 blind spot monitor main switch assembly (warning canceling switch assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H121-11 (B) - Body ground
    Ignition switch ON
    11 to 14 V
    H121-11 (B) - Body ground
    Ignition switch off
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR RH)
  1. Disconnect the P25 blind spot monitor sensor RH connector.

  1. Disconnect the H121 blind spot monitor main switch assembly (warning canceling switch assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P25-3 (BSSW) - H121-8 (D)
    Always
    Below 1 Ω
    P25-3 (BSSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BLIND SPOT MONITOR SENSOR RH (Click here)