Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

DTC    U1002 (CAN No. 2 BUS)    Lost Communication with Gateway Module (Network Gateway ECU)

for Preparation Click here


DESCRIPTION

  1. The network gateway ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN V2 bus.
  2. When the network gateway ECU receives a response signal from the ECUs connected to the CAN V2 bus, the network gateway ECU recognizes and memorizes that the ECU is connected to the CAN V2 bus. Based on this memorized data, the network gateway ECU monitors for malfunctions in the ECUs connected to the CAN V2 bus when communicating with those ECUs. If the network gateway ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN V2 bus, the network gateway ECU determines that a malfunction exists.
  3. If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).

DTC Code
DTC Detection Condition
Trouble Area
U1002
Lost communication with the gateway module.
  1. V2 bus circuit
  2. Network gateway ECU CAN main wire or connector
  3. Blind spot monitor sensor LH CAN branch wire or connector
  4. Blind spot monitor sensor RH CAN branch wire or connector
  5. Network gateway ECU
  6. Blind spot monitor sensor LH
  7. Blind spot monitor sensor RH
  8. No. 3 junction connector
  9. No. 5 junction connector
  10. No. 6 junction connector
  11. No. 7 junction connector
  1. For vehicles with an blind spot monitor system.

WIRING DIAGRAM


C244642E01


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2.CAN BUS WIRE (CHECK MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)


    C242747E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Resistance: Malfunction
    H120-13 (CA2H) - H120-12 (CA2L)
    Ignition switch off
    54 to 69 Ω
    Below 53 Ω: Short in line
    H120-13 (CA2H) - H120-12 (CA2L)
    Ignition switch off
    54 to 69 Ω
    Higher than 70 Ω: Open in CAN main bus line
    H120-13 (CA2H) - H120-2 (BATT)
    Ignition switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    H120-12 (CA2L) - H120-2 (BATT)
    Ignition switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    H120-13 (CA2H) - H120-4 (GND)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short
    H120-12 (CA2L) - H120-4 (GND)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short

    Text in Illustration 
    *a
    Component with harness connected
    (Network Gateway ECU)
    Result 
    Result
    Proceed to
    NG
    1. Open in CAN main bus line
    A
    NG
    1. Short in line
    2. +B short
    3. GND short
    B
    OK
    C



B
Go to step 15

C
Go to step 33
A


3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)


    C242748E01
  1. Disconnect the O47 No. 5 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O47-9 (CANH) - O47-20 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)



NG
Go to step 5
OK


4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)


    C242748E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O47-10 (CANH) - O47-21 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)



NG
Go to step 10
OK

REPLACE NO. 5 JUNCTION CONNECTOR 

5.CONNECT CONNECTOR
  1. Reconnect the O47 No. 5 junction connector.


NEXT


6.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)


    C242748E22
  1. Disconnect the H122 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H122-10 (CANH) - H122-21 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 8
OK


7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)


    C242748E23
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H122-9 (CANH) - H122-20 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
OK

REPLACE NO. 3 JUNCTION CONNECTOR 

8.CONNECT CONNECTOR
  1. Reconnect the H122 No. 3 junction connector.


NEXT


9.CHECK FOR OPEN IN CAN BUS WIRE (NETWORK GATEWAY ECU)


    C242749E01
  1. Disconnect the H120 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H120-13 (CA2H) - H120-12 (CA2L)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Network Gateway ECU)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO NETWORK GATEWAY ECU (NETWORK GATEWAY ECU - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE NETWORK GATEWAY ECU (Click here)  

10.CONNECT CONNECTOR
  1. Reconnect the O47 No. 5 junction connector.


NEXT


11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)


    C242748E05
  1. Disconnect the O48 No. 6 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O48-11 (CANH) - O48-22 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 6 Junction Connector)



NG
Go to step 13
OK


12.CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)


    C242748E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O48-9 (CANH) - O48-20 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 6 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
OK

REPLACE NO. 6 JUNCTION CONNECTOR 

13.CONNECT CONNECTOR
  1. Reconnect the O48 No. 6 junction connector.


NEXT


14.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 JUNCTION CONNECTOR)


    C242676E02
  1. Disconnect the O49 No. 7 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O49-3 (CANH) - O49-2 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 7 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
OK

REPLACE NO. 7 JUNCTION CONNECTOR 

15.CHECK FOR SHORT IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR SIDE)


    C242747E01
  1. Disconnect the O48 No. 6 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H120-13 (CA2H) - H120-12 (CA2L)
    Ignition switch off
    108 to 132 Ω
    H120-13 (CA2H) - H120-4 (GND)
    Ignition switch off
    200 Ω or higher
    H120-12 (CA2L) - H120-4 (GND)
    Ignition switch off
    200 Ω or higher
    H120-13 (CA2H) - H120-2 (BATT)
    Ignition switch off
    6 kΩ or higher
    H120-12 (CA2L) - H120-2 (BATT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Network Gateway ECU)



NG
Go to step 22
OK


16.CHECK FOR SHORT IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - BLIND SPOT MONITOR SENSOR RH)


    C242750E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O48-10 (CANH) - O48-21 (CANL)
    Ignition switch off
    200 Ω or higher
    O48-10 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O48-21 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O48-10 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O48-21 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 6 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 18
OK


17.CHECK FOR SHORT IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)


    C242750E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O48-11 (CANH) - O48-22 (CANL)
    Ignition switch off
    108 to 132 Ω
    O48-11 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O48-22 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O48-11 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O48-22 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 6 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 20
OK

REPLACE NO. 6 JUNCTION CONNECTOR 

18.CONNECT CONNECTOR
  1. Reconnect the O48 No. 6 junction connector.


NEXT


19.CHECK FOR SHORT IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR RH)


    C242752E01
  1. Disconnect the P25 blind spot monitor sensor RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    P25-8 (CA1P) - P25-4 (CA1N)
    Ignition switch off
    54 to 69 Ω
    P25-8 (CA1P) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    P25-4 (CA1N) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    P25-8 (CA1P) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    P25-4 (CA1N) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Blind Spot Monitor Sensor RH)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BLIND SPOT MONITOR SENSOR RH (CA1P, CA1N)
OK

REPLACE BLIND SPOT MONITOR SENSOR RH (Click here)  

20.CONNECT CONNECTOR
  1. Reconnect the O48 No. 6 junction connector.


NEXT


21.CHECK FOR SHORT IN CAN BUS WIRE (NO. 7 JUNCTION CONNECTOR)


    C242753E01
  1. Disconnect the O49 No. 7 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O49-3 (CANH) - O49-2 (CANL)
    Ignition switch off
    108 to 132 Ω
    O49-3 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O49-2 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O49-3 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O49-2 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 7 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
OK

REPLACE NO. 7 JUNCTION CONNECTOR 

22.CONNECT CONNECTOR
  1. Reconnect the O48 No. 6 junction connector.


NEXT


23.CHECK FOR SHORT IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)


    C242750E03
  1. Disconnect the O47 No. 5 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O47-10 (CANH) - O47-21 (CANL)
    Ignition switch off
    108 to 132 Ω
    O47-10 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O47-21 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O47-10 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O47-21 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
OK


24.CHECK FOR SHORT IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR SIDE)


    C242747E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H120-13 (CA2H) - H120-12 (CA2L)
    Ignition switch off
    108 to 132 Ω
    H120-13 (CA2H) - H120-4 (GND)
    Ignition switch off
    200 Ω or higher
    H120-12 (CA2L) - H120-4 (GND)
    Ignition switch off
    200 Ω or higher
    H120-13 (CA2H) - H120-2 (BATT)
    Ignition switch off
    6 kΩ or higher
    H120-12 (CA2L) - H120-2 (BATT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Network Gateway ECU)



NG
Go to step 28
OK


25.CHECK FOR SHORT IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - BLIND SPOT MONITOR SENSOR LH)


    C242750E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O47-11 (CANH) - O47-22 (CANL)
    Ignition switch off
    108 to 132 Ω
    O47-11 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O47-22 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O47-11 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O47-22 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 26
OK

REPLACE NO. 5 JUNCTION CONNECTOR 

26.CONNECT CONNECTOR
  1. Reconnect the O47 No. 5 junction connector.


NEXT


27.CHECK FOR SHORT IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR LH)


    C242752E02
  1. Disconnect the O46 blind spot monitor sensor LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O46-8 (CA1P) - O46-4 (CA1N)
    Ignition switch off
    54 to 69 Ω
    O46-8 (CA1P) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O46-4 (CA1N) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O46-8 (CA1P) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O46-4 (CA1N) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Blind Spot Monitor Sensor LH)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BLIND SPOT MONITOR SENSOR LH (CA1P, CA1N)
OK

REPLACE BLIND SPOT MONITOR SENSOR LH (Click here)  

28.CONNECT CONNECTOR
  1. Reconnect the O47 No. 5 junction connector.


NEXT


29.CHECK FOR SHORT IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)


    C242750E42
  1. Disconnect the H122 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H122-9 (CANH) - H122-20 (CANL)
    Ignition switch off
    108 to 132 Ω
    H122-9 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H122-20 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H122-9 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H122-20 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
OK


30.CHECK FOR SHORT IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)


    C242750E43
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H122-10 (CANH) - H122-21 (CANL)
    Ignition switch off
    108 to 132 Ω
    H122-10 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H122-21 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H122-10 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H122-21 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 31
OK

REPLACE NO. 3 JUNCTION CONNECTOR 

31.CONNECT CONNECTOR
  1. Reconnect the H122 No. 3 junction connector.


NEXT


32.CHECK FOR SHORT IN CAN BUS WIRE (NETWORK GATEWAY ECU)


    C242755E01
  1. Disconnect the H120 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H120-13 (CA2H) - H120-12 (CA2L)
    Ignition switch off
    108 to 132 Ω
    H120-13 (CA2H) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H120-12 (CA2L) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H120-13 (CA2H) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H120-12 (CA2L) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Network Gateway ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO NETWORK GATEWAY ECU (CA2H, CA2L)
OK

REPLACE NETWORK GATEWAY ECU (Click here)  

33.CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND)


    C242749E02
  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the H120 network gateway ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage :
    Tester Connection
    Condition
    Specified Condition
    H120-2 (BATT) - Body ground
    Always
    11 to 14 V
    H120-10 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V
    H120-9 (IG2) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H120-4 (GND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Rear view of wire harness connector
(to Network Gateway ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NETWORK GATEWAY ECU (Click here)