Home › Vehicle Exterior › BODY WELD POINT › CENTER BODY PILLAR
BM27L0U _01 Vehicle Exterior _049510 BODY WELD POINT _0237180 CENTER BODY PILLAR F

BODY WELD POINT  CENTER BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K127271

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

REMOVAL POINT
1.

*a is reused.


K127303C01
2.177,1.323 2.469,0.469 false 2.458,0.26 2.667,0.479 0.208,0.219 10 false *a 0.281,0.51 0.938,0.74 0.656,0.229 10 false 20 (0.79) 6.573,8.458 6.823,8.729 0.25,0.271 10 false *b 0.563,1.938 1.302,2.177 0.74,0.24 10 false 180 (7.09) 2.229,1.896 2.969,2.135 0.74,0.24 10 false 130 (5.12) 3.521,3.167 4.24,3.375 0.719,0.208 10 false 220 (8.66) 1.208,6.885 1.927,7.094 0.719,0.208 10 false 170 (6.69) 3.24,6.875 3.906,7.073 0.667,0.198 10 false 70 (2.76)
*b mm (in.) - -



INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld

INSTALLATION POINT
1.

Before temporarily installing the new parts, weld the rocker outer reinforce, center body pillar lower reinforce and center body inner pillar with the standard number of welding points.

2.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

3.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

4.

After welding the rocker outer reinforce, center body pillar lower reinforce and center body inner pillar to the vehicle side, install the rocker outer panel.

5.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

6.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

7.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K127304C01
2.177,5.177 2.677,4.74 false 5.563,4.896 5.167,4.479 false 2.385,2.51 2.385,2.125 false 6.76,8.49 7.01,8.74 0.25,0.25 10 false *a 2.313,2.521 2.531,2.74 0.219,0.219 10 false *1 2.719,4.573 2.969,4.844 0.25,0.271 10 false *2 4.969,4.344 5.115,4.573 0.146,0.229 10 false *3 1.344,1.333 2.135,1.531 0.792,0.198 10 false 30 (1.18) 2.729,1.354 3.479,1.552 0.75,0.198 10 false 45 (1.77) 4.188,1.344 4.76,1.604 0.573,0.26 10 false 10 (0.39) 4.948,2.938 5.583,3.167 0.635,0.229 10 false 10 (0.39) 2.438,5.25 3.083,5.469 0.646,0.219 10 false 10 (0.39)
*1 Rocker Outer Reinforce *2 Center Body Inner Pillar
*3 Center Body Pillar Lower Reinforce - -
*a mm (in.) - -


K127305C01
4.604,6.125 4.927,6.125 false 1.698,3.802 1.938,3.24 false 3.125,2.625 3.438,2.031 false 3.448,1.865 3.656,2.115 0.208,0.25 10 false *1 1.594,3.802 1.813,4.042 0.219,0.24 10 false *2 4.417,6.021 4.615,6.271 0.198,0.25 10 false *3 6.583,8.427 6.844,8.688 0.26,0.26 10 false *a 4.438,8.198 5.083,8.417 0.646,0.219 10 false 20 (0.79) 6.031,7.854 6.75,8.094 0.719,0.24 10 false 20 (0.79) 5.458,8.104 6.104,8.333 0.646,0.229 10 false 15 (0.59)
*1 Center Body Pillar Lower Reinforce *2 Rocker Outer Reinforce
*3 Center Body Inner Pillar - -
*a mm (in.) - -


K127306C01
3.219,1.802 3.646,1.802 false 3.677,1.698 3.896,1.927 0.219,0.229 10 false *1
*1 Rocker Outer Panel - -