2016-2017 Sequoia Service Manual
3UR-FBE · 3UR-FE
Trouble codes (983)
- P0010An open or short in the Camshaft Oil Control Valve (OCV) for intake side (for Bank 1) circuit (1 trip...
- P0011Intake valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0012Intake valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0013An open or short in the Camshaft Oil Control Valve (OCV) for exhaust side (for Bank 1) circuit (1 trip...
- P0014The exhaust valve timing is not adjusted in the valve timing advance range (2 trip detection logic).
- P0015The exhaust valve timing is not adjusted in the valve timing retard range (1 trip detection logic).
- P0016Deviation in crankshaft position sensor signal and VVT sensor 1 (for Intake Camshaft Bank 1) signal (2 trip...
- P0017Deviation in crankshaft position sensor signal and VVT sensor 1 (for Exhaust Camshaft Bank 1) signal (2 trip...
- P0018Deviation in crankshaft position sensor signal and VVT sensor 2 (for Intake Camshaft Bank 2) signal (2 trip...
- P0019Deviation in crankshaft position sensor signal and VVT sensor 2 (for Exhaust Camshaft Bank 2) signal (2 trip...
- P0020An open or short in the OCV for intake side (for Bank 2) circuit (1 trip detection logic).
- P0021Intake valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0022Intake valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0023An open or short in the OCV for exhaust side (for Bank 2) circuit (1 trip detection logic).
- P0024The exhaust valve timing is not adjusted in the valve timing advance range (2 trip detection logic).
- P0025The exhaust valve timing is not adjusted in the valve timing retard range (1 trip detection logic).
- P0031Air-Fuel Ratio (A/F) sensor heater current is less than 0.8 A (1 trip detection logic).
- P0031Air-Fuel Ratio (A/F) sensor heater current is less than 0.8 A (1 trip detection logic).
- P0032Air-Fuel Ratio (A/F) sensor heater current failure (1 trip detection logic).
- P0032Air-Fuel Ratio (A/F) sensor heater current failure (1 trip detection logic).
- P0037The heater current is less than the specified value while the heater is operating. (1 trip detection logic)
- P0037The heater current is less than the specified value while the heater is operating. (1 trip detection logic)
- P0038The heater current is higher than the specified value while the heater is operating. (1 trip detection logic)
- P0038The heater current is higher than the specified value while the heater is operating. (1 trip detection logic)
- P0051Air-Fuel Ratio (A/F) sensor heater current is less than 0.8 A (1 trip detection logic).
- P0051Air-Fuel Ratio (A/F) sensor heater current is less than 0.8 A (1 trip detection logic).
- P0052Air-Fuel Ratio (A/F) sensor heater current failure (1 trip detection logic).
- P0052Air-Fuel Ratio (A/F) sensor heater current failure (1 trip detection logic).
- P0057The heater current is less than the specified value while the heater is operating. (1 trip detection logic)
- P0057The heater current is less than the specified value while the heater is operating. (1 trip detection logic)
- P0058The heater current is higher than the specified value while the heater is operating. (1 trip detection logic)
- P0058The heater current is higher than the specified value while the heater is operating. (1 trip detection logic)
- P0101Conditions (a), (b), (c), (d) and (e) continue for more than 10 seconds (2 trip detection logic): (a) Engine...
- P0102MAF meter voltage less than 0.2 V for 3 seconds (1 trip detection logic: Engine speed is less than 4000 rpm)...
- P0103MAF meter voltage more than 4.9 V for 3 seconds (1 trip detection logic: Engine speed is less than 4000 rpm)...
- P0111When either of following conditions is met (2 trip detection logic): 1. In duration between engine warmed up...
- P0112Short in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0113Open in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0115Open or short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0116When either of following conditions met (2 trip detection logic): · When cold engine started and engine...
- P0117Short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0118Open in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P011BAll of the following conditions are met (2 trip detection logic): 1. The battery voltage is 10.5 V or higher....
- P0120Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more...
- P0121The difference between the VTA1 and VTA2 voltages is below 0.8 V or higher than 1.6 V for 2 seconds or less...
- P0122Output voltage of VTA1 0.2 V or less for 2 seconds or more (1 trip detection logic)
- P0123Output voltage of VTA1 4.535 V or more for 2 seconds or more (1 trip detection logic)
- P0125Engine Coolant Temperature (ECT) does not reach closed-loop enabling temperature for 20 minutes (this period...
- P0125Engine Coolant Temperature (ECT) does not reach closed-loop enabling temperature for 20 minutes (this period...
- P0128Conditions (a), (b) and (c) met for 5 seconds (2 trip detection logic): (a) Cold start (b) Engine warmed up...
- P0128Conditions (a), (b) and (c) met for 5 seconds (2 trip detection logic): (a) Cold start (b) Engine warmed up...
- P0136· Abnormal voltage output: During active air-fuel ratio control, following conditions (a) and (b) met for...
- P0136· Abnormal voltage output: During active air-fuel ratio control, following conditions (a) and (b) met for...
- P0137· Low voltage (open): During active air-fuel ratio control, following conditions (a) and (b) met for certain...
- P0137· Low voltage (open): During active air-fuel ratio control, following conditions (a) and (b) met for certain...
- P0138· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0138· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0139The HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic).
- P0139The HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic).
- P013AThe HO2 sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (1 trip detection...
- P013AThe HO2 sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (1 trip detection...
- P013CThe HO2 sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (1 trip detection...
- P013CThe HO2 sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (1 trip detection...
- P0141The cumulative heater resistance correction value exceeds the threshold. (2 trip detection logic)
- P0141The cumulative heater resistance correction value exceeds the threshold. (2 trip detection logic)
- P014CThe "Rich to Lean response rate deterioration level*" value is less than the standard. (2 trip detection...
- P014CThe "Rich to Lean response rate deterioration level*" value is less than the standard. (2 trip detection...
- P014DThe "Lean to Rich response rate deterioration level*" value is more than the standard. (2 trip detection...
- P014DThe "Lean to Rich response rate deterioration level*" value is more than the standard. (2 trip detection...
- P014EThe "Rich to Lean response rate deterioration level*" value is less than the standard. (2 trip detection...
- P014EThe "Rich to Lean response rate deterioration level*" value is less than the standard. (2 trip detection...
- P014FThe "Lean to Rich response rate deterioration level*" value is more than the standard. (2 trip detection...
- P014FThe "Lean to Rich response rate deterioration level*" value is more than the standard. (2 trip detection...
- P0156· Abnormal voltage output: During active air-fuel ratio control, following conditions (a) and (b) met for...
- P0156· Abnormal voltage output: During active air-fuel ratio control, following conditions (a) and (b) met for...
- P0157· Low voltage (open): During active air-fuel ratio control, following conditions (a) and (b) met for certain...
- P0157· Low voltage (open): During active air-fuel ratio control, following conditions (a) and (b) met for certain...
- P0158· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0158· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0159The HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic).
- P0159The HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic).
- P015AThe "Rich to Lean delay level*" value is less than the standard. (2 trip detection logic)
- P015AThe "Rich to Lean delay level*" value is less than the standard. (2 trip detection logic)
- P015BThe "Lean to Rich delay level*" value is more than the standard. (2 trip detection logic)
- P015BThe "Lean to Rich delay level*" value is more than the standard. (2 trip detection logic)
- P015CThe "Rich to Lean delay level*" value is less than the standard. (2 trip detection logic)
- P015CThe "Rich to Lean delay level*" value is less than the standard. (2 trip detection logic)
- P015DThe "Lean to Rich delay level*" value is more than the standard. (2 trip detection logic)
- P015DThe "Lean to Rich delay level*" value is more than the standard. (2 trip detection logic)
- P0161The cumulative heater resistance correction value exceeds the threshold. (2 trip detection logic)
- P0161The cumulative heater resistance correction value exceeds the threshold. (2 trip detection logic)
- P0171With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip...
- P0172With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip...
- P0174With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip...
- P0175With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip...
- P0220Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more...
- P0222Output voltage of VTA2 1.75 V or less for 2 seconds or more (1 trip detection logic)
- P0223Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V for 2 seconds or more (1 trip...
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions below is detected (2...
- P0301Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0302Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0303Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0304Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0305Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0306Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0307Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0308Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0327Output voltage of knock sensor (for Bank 1 Sensor 1) is 0.5 V or less (1 trip detection logic)
- P0328Output voltage of knock sensor (for Bank 1 Sensor 1) is 4.5 V or more (1 trip detection logic)
- P032COutput voltage of knock sensor (for Bank 1 Sensor 2) is 0.5 V or less (1 trip detection logic)
- P032DOutput voltage of knock sensor (for Bank 1 Sensor 2) is 4.5 V or more (1 trip detection logic)
- P0332Output voltage of knock sensor (for Bank 2 Sensor 1) is 0.5 V or less (1 trip detection logic)
- P0333Output voltage of knock sensor (for Bank 2 Sensor 1) is 4.5 V or more (1 trip detection logic)
- P0335· No CKP sensor signal to ECM while cranking (1 trip detection logic) · No CKP sensor signal to ECM at engine...
- P0337Output voltage of CKP sensor 0.3 V or less for 4 seconds (1 trip detection logic)
- P0338Output voltage of CKP sensor 4.7 V or more for 4 seconds (1 trip detection logic)
- P0339Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more (1 trip detection...
- P033COutput voltage of knock sensor (for Bank 2 Sensor 2) is 0.5 V or less (1 trip detection logic)
- P033DOutput voltage of knock sensor (for Bank 2 Sensor 2) is 4.5 V or more (1 trip detection logic)
- P0340No VVT sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic).
- P0342The output voltage of the VVT sensor (for intake side of Bank 1, 2) is below 0.3 V for 4 seconds (1 trip...
- P0343The output voltage of the VVT sensor (for intake side of Bank 1, 2) is higher than 4.7 V for 4 seconds (1...
- P0345No VVT sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic).
- P0347The output voltage of the VVT sensor (for intake side of Bank 1, 2) is below 0.3 V for 4 seconds (1 trip...
- P0348The output voltage of the VVT sensor (for intake side of Bank 1, 2) is higher than 4.7 V for 4 seconds (1...
- P0351No IGF signal to ECM while engine running (1 trip detection logic)
- P0352No IGF signal to ECM while engine running (1 trip detection logic)
- P0353No IGF signal to ECM while engine running (1 trip detection logic)
- P0354No IGF signal to ECM while engine running (1 trip detection logic)
- P0355No IGF signal to ECM while engine running (1 trip detection logic)
- P0356No IGF signal to ECM while engine running (1 trip detection logic)
- P0357No IGF signal to ECM while engine running (1 trip detection logic)
- P0358No IGF signal to ECM while engine running (1 trip detection logic)
- P0365No VVT sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)
- P0367Output voltage of VVT sensor less than 0.3 V 4 seconds (1 trip detection logic)
- P0368Output voltage of VVT sensor more than 4.7 V 4 seconds (1 trip detection logic)
- P0390No VVT sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)
- P0392Output voltage of VVT sensor less than 0.3 V 4 seconds (1 trip detection logic)
- P0393Output voltage of VVT sensor more than 4.7 V 4 seconds (1 trip detection logic)
- P0412After cold engine starts, all of following conditions met (1 trip detection logic): 1. Secondary Air...
- P0415After cold engine starts, all of following conditions met (1 trip detection logic): 1. Secondary Air...
- P0418After cold engine starts, all of following conditions met (2 trip detection logic): 1. Secondary Air...
- P0419After cold engine starts, all of following conditions met (2 trip detection logic): 1. Secondary Air...
- P0420OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic)
- P0430OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic)
- P043E, P043F, P2401, P2402 and P2419 present when one of following conditions met during key-off EVAP...
- P043FP043F
- P0441Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0443Terminal voltage of ECM output circuit does not correspond with drive signals from ECM to purge VSV (1 trip...
- P0451Sensor output voltage fluctuates frequently within a certain time period.
- P0452EVAP pressure less than 42.11009 kPa for 0.5 seconds.
- P0453EVAP pressure more than 123.76147 kPa for 0.5 seconds.
- P0455Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0456Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0500While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (2 trip detection logic)
- P0504Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON...
- P0505Idling speed continues to vary greatly from target idling speed (2 trip detection logic)
- P0505Idling speed continues to vary greatly from target idling speed (2 trip detection logic)
- P050AInsufficient mass air flow at cold start (2 trip detection logic)
- P050BInsufficient ignition timing retard at cold start (2-trip detection logic)
- P050BInsufficient ignition timing retard at cold start (2-trip detection logic)
- P0550Power steering oil pressure sensor voltage less than 0.28 V, or more than 4.9 V for 0.5 seconds while engine...
- P0552Power steering oil pressure sensor voltage less than 0.28 V for 0.5 seconds while engine running. (1 trip...
- P0553Power steering oil pressure sensor voltage more than 4.9 V for 0.5 seconds while engine running. (1 trip...
- P0560Open in ECM back up power source circuit (1 trip detection logic)
- P0604ECM RAM errors
- P0606When either condition below is met: · ECM main CPU error · ECM sub CPU error
- P0607· ECM CPUs malfunction · HO2S transistors malfunction
- P060AWhen either condition below is met: · ECM main CPU error · ECM sub CPU error · Electronic throttle monitoring...
- P060BECM main CPU communication error
- P060DWhen either condition below is met: · ECM main CPU error · ECM sub CPU error
- P060EWhen either condition below is met: · ECM main CPU error · ECM sub CPU error
- P0617When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20...
- P062FECM internal error (EEPROM)
- P0630When either condition below is met: (1 trip detection logic) · VIN not stored in ECM · Input VIN incorrect
- P0630When either condition below is met: (1 trip detection logic) · VIN not stored in ECM · Input VIN incorrect
- P0657Throttle actuator power supply error
- P0724Stop light switch remains ON even when vehicle is driven in GO (30 km/h (18.65 mph) or more) and STOP (less...
- P101DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P101DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P102DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P102DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P103DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P103DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P105DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P105DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P106BThe pressure detected by the canister pressure sensor (Vapor Pressure Pump*) and the pressure detected by the...
- P1340No camshaft position sensor signal to ECM during cranking (2 trip detection logic)
- P1342Output voltage of camshaft position sensor less than 0.3 V for 4 seconds (1 trip detection logic)
- P1343Output voltage of camshaft position sensor more than 4.7 V for 4 seconds (1 trip detection logic)
- P144COpen or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
- P144DOpen or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
- P1603After monitoring for startability problems (P1604) finishes and 2 seconds or more elapse after starting the...
- P1604Either condition is met: · The engine speed is below 500 rpm with the STA signal on for a certain amount of...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1607ECM CPUs malfunction
- P1613Either of following conditions (1) or (2) met: (1) All of following conditions met (1 trip detection logic):...
- P1614Either of following conditions (1) or (2) met: (1) All of following conditions met (1 trip detection logic):...
- P2102Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic): (a) Throttle actuator duty ratio...
- P2103Either of following conditions met (1 trip detection logic): · Hybrid IC diagnosis signal failure · Hybrid IC...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2111Throttle actuator does not close when signaled by ECM (1 trip detection logic)
- P2112Throttle actuator does not open when signaled by ECM (1 trip detection logic)
- P2118Open in ETCS power source (+BM) circuit (1 trip detection logic)
- P2119Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
- P2120VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2121Either conditions (1) or (2) met for 0.5 seconds (1 trip detection logic): (1) Difference between VPA and...
- P2122VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic)
- P2123VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic)
- P2125VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2127VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic)
- P2128Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 4.8 V or more (b)...
- P2135Either condition (a) or (b) met (1 trip detection logic): (a) Difference between output voltages of VTA1 and...
- P2138Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2197Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2197Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2198Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2198Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P219AThe difference in air-fuel ratios between the cylinders exceeds the threshold.
- P219AThe difference in air-fuel ratios between the cylinders exceeds the threshold.
- P219BThe difference in air-fuel ratios between the cylinders exceeds the threshold.
- P219BThe difference in air-fuel ratios between the cylinders exceeds the threshold.
- P219CThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219CThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219DThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219DThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219EThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219EThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219FThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219FThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A0The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A0The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A1The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A1The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A2The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A2The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A3The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A3The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P2237Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2237Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2238· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2238· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2239A1A+/A2A+ voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2239A1A+/A2A+ voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2240Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2240Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2241· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2241· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2242A1A+/A2A+ voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2242A1A+/A2A+ voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2252A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2252A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2253A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2253A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2255A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2255A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2256A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2256A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2401P2401
- P2402P2402
- P2419P2419
- P2420Following condition met during key-off EVAP monitor: · EVAP pressure change when vent valve closed (ON) less...
- P2431Pressure sensor indicates less than 45.6 kPa (342 mmHg), or more than 135 kPa (1013 mmHg) (2 trip detection...
- P2432While engine running, voltage output of pressure sensor remains below 0.5 V (1 trip detection logic)
- P2433While engine running, voltage output of pressure sensor remains above 4.5 V (1 trip detection logic)
- P2436Pressure sensor indicates less than 45.6 kPa (342 mmHg), or more than 135 kPa (1013 mmHg) (2 trip detection...
- P2437While engine running, voltage output of pressure sensor remains below 0.5 V (1 trip detection logic)
- P2438While engine running, voltage output of pressure sensor remains above 4.5 V (1 trip detection logic)
- P2440The pressure sensor detects pulsation of the exhaust gas despite the ECM commanding the Air Switching Valve...
- P2440The pressure sensor detects pulsation of the exhaust gas despite the ECM commanding the Air Switching Valve...
- P2441The pressure sensor detects no pulsation of the exhaust gas despite the ECM commanding the Air Switching...
- P2441The pressure sensor detects no pulsation of the exhaust gas despite the ECM commanding the Air Switching...
- P2442The pressure sensor detects pulsation of the exhaust gas despite the ECM commanding the Air Switching Valve...
- P2442The pressure sensor detects pulsation of the exhaust gas despite the ECM commanding the Air Switching Valve...
- P2443The pressure sensor detects no pulsation of the exhaust gas despite the ECM commanding the Air Switching...
- P2443The pressure sensor detects no pulsation of the exhaust gas despite the ECM commanding the Air Switching...
- P2444Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off (2 trip...
- P2445Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on (2 trip...
- P2446Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off (2 trip...
- P2447Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on (2 trip...
- P2610ECM internal malfunction
- P0010Open or short in OCV (for intake side of bank 1) circuit (1 trip detection logic)
- P0011Intake valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0012Intake valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0013Open or short in OCV (for exhaust side of bank 1) circuit (1 trip detection logic)
- P0014Exhaust valve timing is not adjusted in valve timing advance range (2 trip detection logic)
- P0015Exhaust valve timing is not adjusted in valve timing retard range (1 trip detection logic)
- P0016Deviation in crankshaft position sensor signal and VVT sensor (for Intake Side of Bank 1) signal (2 trip...
- P0017Deviation in crankshaft position sensor signal and VVT sensor (for Exhaust Side of Bank 1) signal (2 trip...
- P0018Deviation in crankshaft position sensor signal and VVT sensor (for Intake Side of Bank 2) signal (2 trip...
- P0019Deviation in crankshaft position sensor signal and VVT sensor (for Exhaust Camshaft Bank 2) signal (2 trip...
- P0020Open or short in OCV (for intake side of bank 2) circuit (1 trip detection logic)
- P0021Intake valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0022Intake valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0023Open or short in OCV (for exhaust side of bank 2) circuit (1 trip detection logic)
- P0024Exhaust valve timing is not adjusted in valve timing advance range (2 trip detection logic)
- P0025Exhaust valve timing is not adjusted in valve timing retard range (1 trip detection logic)
- P0031Air-Fuel Ratio (A/F) sensor heater current less than 0.8 A (1 trip detection logic)
- P0032Air-Fuel Ratio (A/F) sensor heater current failure (1 trip detection logic)
- P0037The heater current is less than the specified value while the heater is operating. (1 trip detection logic)
- P0038The heater current is higher than the specified value while the heater is operating. (1 trip detection logic)
- P0051Air-Fuel Ratio (A/F) sensor heater current less than 0.8 A (1 trip detection logic)
- P0052Air-Fuel Ratio (A/F) sensor heater current failure (1 trip detection logic)
- P0057The heater current is less than the specified value while the heater is operating. (1 trip detection logic)
- P0058The heater current is higher than the specified value while the heater is operating. (1 trip detection logic)
- P0101Conditions (a), (b), (c), (d) and (e) continue for more than 10 seconds (2 trip detection logic): (a) Engine...
- P0102MAF meter voltage less than 0.2 V for 3 seconds (1 trip detection logic: Engine speed less than 4000 rpm) (2...
- P0103MAF meter voltage more than 4.9 V for 3 seconds (1 trip detection logic: Engine speed less than 4000 rpm) (2...
- P0111When either condition below is met: 1. The intake air temperature change is small, from the previous trip...
- P0112Short in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0113Open in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0115Open or short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0116When either of following conditions met (2 trip detection logic): · When cold engine started and engine...
- P0117Short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0118Open in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P011BAll of the following conditions are met (2 trip detection logic): 1. The battery voltage is 10.5 V or higher....
- P0120Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when...
- P0121Difference between VTA1 and VTA2 voltages less than 0.8 V or more than 1.6 V for 2 seconds (1 trip detection...
- P0122Output voltage of VTA1 0.2 V or less for 2 seconds when accelerator pedal depressed (1 trip detection logic)
- P0123Output voltage of VTA1 4.535 V or more for 2 seconds when accelerator pedal depressed (1 trip detection logic)
- P0125Engine Coolant Temperature (ECT) does not reach closed-loop enabling temperature for 20 minutes (this period...
- P0125Engine Coolant Temperature (ECT) does not reach closed-loop enabling temperature for 20 minutes (this period...
- P0128Conditions (a), (b) and (c) met for 5 seconds (2 trip detection logic): (a) Cold start (b) Engine warmed up...
- P0128Conditions (a), (b) and (c) met for 5 seconds (2 trip detection logic): (a) Cold start (b) Engine warmed up...
- P0136· Abnormal voltage output: During active air-fuel ratio control, following conditions (a) and (b) met for...
- P0136· Abnormal voltage output: During active air-fuel ratio control, following conditions (a) and (b) met for...
- P0137· Low voltage (open): During active air-fuel ratio control, following conditions (a) and (b) met for certain...
- P0137· Low voltage (open): During active air-fuel ratio control, following conditions (a) and (b) met for certain...
- P0138· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0138· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0139· HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic)
- P0139· HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic)
- P013A· HO2 sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (2 trip detection...
- P013A· HO2 sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (2 trip detection...
- P013C· HO2 sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (2 trip detection...
- P013C· HO2 sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (2 trip detection...
- P0141The cumulative heater resistance correction value exceeds the threshold. (2 trip detection logic)
- P014CThe "Rich to Lean response rate deterioration level*" value is standard or less (2 trip detection logic).
- P014CThe "Rich to Lean response rate deterioration level*" value is standard or less (2 trip detection logic).
- P014DThe "Lean to Rich response rate deterioration level*" value is standard or more (2 trip detection logic).
- P014DThe "Lean to Rich response rate deterioration level*" value is standard or more (2 trip detection logic).
- P014EThe "Rich to Lean response rate deterioration level*" value is standard or less (2 trip detection logic).
- P014EThe "Rich to Lean response rate deterioration level*" value is standard or less (2 trip detection logic).
- P014FThe "Lean to Rich response rate deterioration level*" value is standard or more (2 trip detection logic).
- P014FThe "Lean to Rich response rate deterioration level*" value is standard or more (2 trip detection logic).
- P0156· Abnormal voltage output: During active air-fuel ratio control, following conditions (a) and (b) met for...
- P0156· Abnormal voltage output: During active air-fuel ratio control, following conditions (a) and (b) met for...
- P0157· Low voltage (open): During active air-fuel ratio control, following conditions (a) and (b) met for certain...
- P0157· Low voltage (open): During active air-fuel ratio control, following conditions (a) and (b) met for certain...
- P0158· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0158· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0159· HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic)
- P0159· HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic)
- P015AThe "Rich to Lean delay level*" value is standard or more (2 trip detection logic).
- P015AThe "Rich to Lean delay level*" value is standard or more (2 trip detection logic).
- P015BThe "Lean to Rich delay level*" value is standard or more (2 trip detection logic).
- P015BThe "Lean to Rich delay level*" value is standard or more (2 trip detection logic).
- P015CThe "Rich to Lean delay level*" value is standard or more (2 trip detection logic).
- P015CThe "Rich to Lean delay level*" value is standard or more (2 trip detection logic).
- P015DThe "Lean to Rich delay level*" value is standard or more (2 trip detection logic).
- P015DThe "Lean to Rich delay level*" value is standard or more (2 trip detection logic).
- P0161The cumulative heater resistance correction value exceeds the threshold. (2 trip detection logic)
- P0171With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip...
- P0172With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip...
- P0174With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip...
- P0175With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip...
- P0220Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when...
- P0222Output voltage of VTA2 1.75 V or less for 2 seconds when accelerator pedal depressed (1 trip detection logic)
- P0223Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V for 2 seconds when accelerator pedal...
- P0230When either condition below is met (1 trip detection logic): · When fuel pump is operating: · Remaining fuel...
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions below is detected (2...
- P0301Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0302Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0303Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0304Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0305Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0306Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0307Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0308Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0327Output voltage of knock sensor (for Bank 1 Sensor 1) is 0.5 V or less (1 trip detection logic)
- P0328Output voltage of knock sensor (for Bank 1 Sensor 1) is 4.5 V or more (1 trip detection logic)
- P032COutput voltage of knock sensor (for Bank 1 Sensor 2) is 0.5 V or less (1 trip detection logic)
- P032DOutput voltage of knock sensor (for Bank 1 Sensor 2) is 4.5 V or more (1 trip detection logic)
- P0332Output voltage of knock sensor (for Bank 2 Sensor 1) is 0.5 V or less (1 trip detection logic)
- P0333Output voltage of knock sensor (for Bank 2 Sensor 1) is 4.5 V or more (1 trip detection logic)
- P0335· No CKP sensor signal to ECM while cranking (1 trip detection logic) · No CKP sensor signal to ECM at engine...
- P0337Output voltage of CKP sensor 0.3 V or less for 4 seconds (1 trip detection logic)
- P0338Output voltage of CKP sensor 4.7 V or more for 4 seconds (1 trip detection logic)
- P0339Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more (1 trip detection...
- P033COutput voltage of knock sensor (for Bank 2 Sensor 2) is 0.5 V or less (1 trip detection logic)
- P033DOutput voltage of knock sensor (for Bank 2 Sensor 2) is 4.5 V or more (1 trip detection logic)
- P0340No VVT sensor signal to ECM during engine running (1 trip detection logic)
- P0342Output voltage of VVT sensor less than 0.3 V for 4 seconds (1 trip detection logic)
- P0343Output voltage of VVT sensor more than 4.7 V for 4 seconds (1 trip detection logic)
- P0345No VVT sensor signal to ECM during engine running (1 trip detection logic)
- P0347Output voltage of VVT sensor less than 0.3 V for 4 seconds (1 trip detection logic)
- P0348Output voltage of VVT sensor more than 4.7 V for 4 seconds (1 trip detection logic)
- P0351No IGF signal to ECM while engine running (1 trip detection logic)
- P0352No IGF signal to ECM while engine running (1 trip detection logic)
- P0353No IGF signal to ECM while engine running (1 trip detection logic)
- P0354No IGF signal to ECM while engine running (1 trip detection logic)
- P0355No IGF signal to ECM while engine running (1 trip detection logic)
- P0356No IGF signal to ECM while engine running (1 trip detection logic)
- P0357No IGF signal to ECM while engine running (1 trip detection logic)
- P0358No IGF signal to ECM while engine running (1 trip detection logic)
- P0365No VVT sensor signal to ECM during engine running (1 trip detection logic)
- P0367Output voltage of VVT sensor less than 0.3 V 4 seconds (1 trip detection logic)
- P0368Output voltage of VVT sensor more than 4.7 V 4 seconds (1 trip detection logic)
- P0390No VVT sensor signal to ECM during engine running (1 trip detection logic)
- P0392Output voltage of VVT sensor less than 0.3 V 4 seconds (1 trip detection logic)
- P0393Output voltage of VVT sensor more than 4.7 V 4 seconds (1 trip detection logic)
- P0412After cold engine starts, all of following conditions met (1 trip detection logic): 1. Secondary Air...
- P0415After cold engine starts, all of following conditions met (1 trip detection logic): 1. Secondary Air...
- P0418After cold engine starts, all of following conditions met (2 trip detection logic): 1. Secondary Air...
- P0419After cold engine starts, all of following conditions met (2 trip detection logic): 1. Secondary Air...
- P0420OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic)
- P0420OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic)
- P0430OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic)
- P0430OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic)
- P043E, P043F, P2401, P2402 and P2419 present when one of following conditions met during key-off EVAP...
- P043FP043F
- P0441Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0451Sensor output voltage fluctuates frequently within a certain time period.
- P0452EVAP pressure less than 42.11009 kPa-a for 0.5 seconds.
- P0453EVAP pressure more than 123.76147 kPa-a for 0.5 seconds.
- P0455Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0456Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0461Despite consuming a certain amount of fuel, the change in the resistance value of the fuel sender gauge is...
- P0462The resistance value of the fuel sender gauge is below the threshold. (2 trip detection logic)
- P0463The resistance value of the fuel sender gauge exceeds the threshold. (2 trip detection logic)
- P0500While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (2 trip detection logic)
- P0504Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON...
- P0505Idling speed continues to vary greatly from target idling speed (2 trip detection logic)
- P0505Idling speed continues to vary greatly from target idling speed (2 trip detection logic)
- P050AInsufficient mass air flow at cold start (2 trip detection logic)
- P050AInsufficient mass air flow at cold start (2 trip detection logic)
- P050BInsufficient ignition timing retard at cold start (2-trip detection logic)
- P050BInsufficient ignition timing retard at cold start (2-trip detection logic)
- P0550Power steering oil pressure sensor voltage less than 0.28 V, or more than 4.9 V for 0.5 seconds while engine...
- P0552Power steering oil pressure sensor voltage less than 0.28 V for 0.5 seconds while engine running. (1 trip...
- P0553Power steering oil pressure sensor voltage more than 4.9 V for 0.5 seconds while engine running. (1 trip...
- P0560Open in ECM back up power source circuit (1 trip detection logic)
- P0604ECM RAM errors
- P0606When either condition below is met: · ECM main CPU error · ECM sub CPU error
- P0607· ECM CPUs malfunction · Heated oxygen sensor transistor (built into the ECM) malfunction
- P060AWhen either condition below is met: · ECM main CPU error · ECM sub CPU error · Electronic throttle monitoring...
- P060BECM main CPU communication error
- P060DWhen either condition below is met: · ECM main CPU error · ECM sub CPU error
- P060EWhen either condition below is met: · ECM main CPU error · ECM sub CPU error
- P0617When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20...
- P062FECM internal error (EEPROM)
- P0630When either condition below is met: (1 trip detection logic) · VIN not stored in ECM · Input VIN incorrect
- P0657Throttle actuator power supply error
- P0724Stop light switch remains ON even when vehicle is driven in GO (30 km/h (18.65 mph) or more) and STOP (less...
- P101DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P102DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P103DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P105DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P106BThe pressure detected by the canister pressure sensor (Vapor Pressure Pump*) and the pressure detected by the...
- P109CThe fuel pressure switching valve relay circuit is open or shorted to ground. (1 trip detection logic)
- P109DThe fuel pressure switching valve relay circuit is shorted to the power supply. (1 trip detection logic)
- P1340No camshaft position sensor signal to ECM during cranking (2 trip detection logic)
- P1342Output voltage of camshaft position sensor less than 0.3 V for 4 seconds (1 trip detection logic)
- P1343Output voltage of camshaft position sensor more than 4.7 V for 4 seconds (1 trip detection logic)
- P144COpen or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
- P144DOpen or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
- P1603After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the...
- P1604Either condition is met: · The engine speed is below 500 rpm with the STA signal on for a certain amount of...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1607ECM CPUs malfunction
- P1613Either of following conditions (1) or (2) met: (1) All of following conditions met (1 trip detection logic):...
- P1614Either of following conditions (1) or (2) met: (1) All of following conditions met (1 trip detection logic):...
- P2102Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic): (a) Throttle actuator duty ratio...
- P2103Either of following conditions met (1 trip detection logic): · Hybrid IC diagnosis signal failure · Hybrid IC...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2111Throttle actuator does not close when signaled by ECM (1 trip detection logic)
- P2112Throttle actuator does not open when signaled by ECM (1 trip detection logic)
- P2118Open in ETCS power source (+BM) circuit (1 trip detection logic)
- P2119Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
- P2120VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2121Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic) 1. Difference between VPA...
- P2122VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic)
- P2123VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic)
- P2125VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2127VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic)
- P2128Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 4.8 V or more (b)...
- P2135Either condition (a) or (b) met (1 trip detection logic): (a) Difference between output voltages of VTA1 and...
- P2138Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2197Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2197Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2198Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2198Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P219AThe difference in air-fuel ratios between the cylinders exceeds the threshold.
- P219BThe difference in air-fuel ratios between the cylinders exceeds the threshold.
- P219CThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219DThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219EThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219FThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A0The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A1The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A2The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A3The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P2237Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2237Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2238· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2238· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2239Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+ voltage more...
- P2239Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+ voltage more...
- P2240Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2240Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2241· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2241· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2242Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+ voltage more...
- P2242Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+ voltage more...
- P2252A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2252A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2253A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2253A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2255A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2255A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2256A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2256A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2401P2401
- P2402P2402
- P2419P2419
- P2420Following condition met during key-off EVAP monitor: · EVAP pressure change when vent valve closed (ON) less...
- P2431Pressure sensor indicates less than 45.63 kPa (342 mmHg), or more than 135 kPa (1013 mmHg) (2 trip detection...
- P2432While engine running, voltage output of pressure sensor remains below 0.5 V (1 trip detection logic)
- P2433While engine running, voltage output of pressure sensor remains above 4.5 V (1 trip detection logic)
- P2436Pressure sensor indicates less than 45.63 kPa (342 mmHg), or more than 135 kPa (1013 mmHg) (2 trip detection...
- P2437While engine running, voltage output of pressure sensor remains below 0.5 V (1 trip detection logic)
- P2438While engine running, voltage output of pressure sensor remains above 4.5 V (1 trip detection logic)
- P2440Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
- P2440Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
- P2441The air switching valve (for bank 1) is stuck close for 7 seconds while the engine is running (2 trip...
- P2441The air switching valve (for bank 1) is stuck close for 7 seconds while the engine is running (2 trip...
- P2442Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
- P2442Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
- P2443The air switching valve (for bank 2) is stuck close for 7 seconds while the engine is running (2 trip...
- P2443The air switching valve (for bank 2) is stuck close for 7 seconds while the engine is running (2 trip...
- P2444Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off (2 trip...
- P2444Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off (2 trip...
- P2445Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on (2 trip...
- P2445Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on (2 trip...
- P2446Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off (2 trip...
- P2446Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off (2 trip...
- P2447Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on (2 trip...
- P2447Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on (2 trip...
- P2610ECM internal malfunction
- U0155Following conditions are met for 2.9 seconds (1 trip detection logic): 1. Ignition switch to ON. 2. Battery...
- C1267During cruise control operation a micro switch error is stored under the following conditions: A micro switch...
- P0500The vehicle speed signal from the vehicle speed sensor is cut for 0.14 seconds. or more while the cruise...
- P0503Momentary interruption and noise malfunction codes are detected when a rapid change of vehicle speed occurs...
- P0571Voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 seconds. or more.
- P0575When STV signal is input and cruise control continues for 0.4 seconds. When malfunction STV signal is...
- C1267During cruise control operation a micro switch error is stored under the following conditions: A micro switch...
- P0500The vehicle speed signal from the vehicle speed sensor is cut for 0.14 seconds or more while the cruise...
- P0503Momentary interruption and noise malfunction codes are detected when a rapid change of vehicle speed occurs...
- P0571Voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 seconds. or more.
- P0575When STV signal is input and cruise control continues for 0.4 seconds. When malfunction STV signal is...
- P1570The ECM detects a laser radar sensor malfunction signal for 0.15 seconds or more while the dynamic laser...
- P1572The ECU detects that the laser radar sensor beam axis is in an incorrect position (0.15 seconds or more)...
- P1575The ECM receives a buzzer abnormal signal for 0.2 seconds or more while the dynamic laser cruise control is...
- P1578The ECM receives a brake system error signal for 0.2 seconds or more while the dynamic laser cruise control...
- P1615While the dynamic laser cruise control is either preparing for operation or operating, if communication data...
- P1616While the dynamic laser cruise control is either preparing for operation or operating, if the ECM...
- P1617While the dynamic laser cruise control is either preparing for operation or operating, if a designation...
- P1630While the dynamic laser cruise control is either preparing for operation or operating, if communication data...
- P1631While the dynamic laser cruise control is either preparing for operation or operating, if the ECM...
- U0100While the dynamic laser cruise control is either preparing for operation or operating, if the ECM...
- U0122While dynamic laser cruise control is either preparing for operation or operating, if communication data from...
- U0123While the dynamic laser cruise control is either preparing for operation or operating, the ECM continuously...
- U0126While the dynamic laser cruise control is either preparing for operation or operating, if the ECM...
- U0235The ECM detects a communication error signal (from the laser radar sensor to the distance control ECU) for...
- U1101While the dynamic laser cruise control is either preparing for operation or operating, if communication data...
- U1102The ECM detects a communication error signal (from the distance control ECU to the laser radar sensor) for...
- P0705When one of following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously (2...
- P0711Either condition is met (2-trip detection logic): (a) Certain monitor enabling conditions are met and the ATF...
- P0711Either condition is met (2-trip detection logic): (a) Certain monitor enabling conditions are met and the ATF...
- P0712ATF temperature sensor resistance is below 79 Ω for 0.5 sec. or more (1 trip detection logic)
- P0713ATF temperature sensor resistance is higher than 156 kΩ for 0.5 sec. or more either of the following...
- P0717All conditions below are detected for 5 seconds or more (1-trip detection logic) (a) Gear change is not...
- P0722All conditions below are detected 5 seconds or more continuously (2-trip detection logic) (a) No signal from...
- P07296th gearshift malfunction: The ECM determines there is a malfunction when both of the following conditions...
- P0748The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting...
- P0751S1 stuck ON malfunction*1: The ECM determines there is a malfunction when the following conditions are both...
- P0756S2 stuck ON malfunction*1: Shifting to 3rd and 5th gears is impossible. The ECM determines there is a...
- P0761S3 stuck ON malfunction*1: When the ECM directs the gearshift to switch to 5th or 6th gear, the engine...
- P0766S4 stuck OFF malfunction or brake control valve malfunction*: Shifting to 5th and 6th gears is impossible....
- P0776SL2 stuck ON malfunction or brake control valve malfunction*: Shifting to 5th and 6th gears is impossible....
- P0778The ECM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears...
- P0781When conditions (a) and (b), or (a) and (c) are met. (2-trip detection logic) (a) When the ECM directs the...
- P0894The ECM detects a malfunction on SLT, S1, S2, S3, S4, SL2, gear 6 incorrect ratio (sequence valve) or 1-2...
- P0973ECM detects short in solenoid valve S1 circuit 2 times when solenoid valve S1 is operated (1 trip detection...
- P0974ECM detects open in solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated (1 trip...
- P0976ECM detects short in solenoid valve S2 circuit 2 times when solenoid valve S2 is operated (1 trip detection...
- P0977ECM detects open in solenoid valve S2 circuit 2 times when solenoid valve S2 is not operated (1 trip...
- P0979ECM detects short in solenoid valve S3 circuit 2 times when solenoid valve S3 is operated (1 trip detection...
- P0980ECM detects open in solenoid valve S3 circuit 2 times when solenoid valve S3 is not operated (1 trip...
- P0982ECM detects short in solenoid valve S4 circuit 2 times when solenoid valve S4 is operated (1 trip detection...
- P0983ECM detects open in solenoid valve S4 circuit 2 times when solenoid valve S4 is not operated (1 trip...
- P0985ECM detects short in solenoid valve SR circuit 2 times when solenoid valve SR is operated (1 trip detection...
- P0986ECM detects open in solenoid valve SR circuit 2 times when solenoid valve SR is not operated (1 trip...
- P2714The ECM detects a malfunction on SLT (ON side) according to the revolution difference of the turbine and the...
- P2716Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip...
- P2742No. 2 ATF temperature sensor resistance is less than 25 Ω (0.046 V) for 0.5 seconds or more. (1-trip...
- P2743No. 2 ATF temperature sensor resistance is higher than 156 kΩ (4.915 V) for 0.5 sec. or more and either...
- P2757Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h (50 mph)), or lock-up...
- P2759Open or short is detected in shift solenoid valve SLU circuit for 1 second or more while driving (1 trip...
- P0705When one of following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously (2...
- P0711Either condition is met (2-trip detection logic): (a) Certain monitor enabling conditions are met and the ATF...
- P0711Either condition is met (2-trip detection logic): (a) Certain monitor enabling conditions are met and the ATF...
- P0712ATF temperature sensor resistance is below 79 Ω for 0.5 sec. or more (1 trip detection logic)
- P0713ATF temperature sensor resistance is higher than 156 kΩ for 0.5 sec. or more either of the following...
- P0717All conditions below are detected for 5 seconds or more (1-trip detection logic) (a) Gear change is not...
- P0722All conditions below are detected 5 seconds or more continuously (2-trip detection logic) (a) No signal from...
- P07296th gearshift malfunction: The ECM determines there is a malfunction when both of the following conditions...
- P0748The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting...
- P0751S1 stuck ON malfunction*1: The ECM determines there is a malfunction when the following conditions are both...
- P0756S2 stuck ON malfunction*1: Shifting to 3rd and 5th gears is impossible. The ECM determines there is a...
- P0761S3 stuck ON malfunction*1: When the ECM directs the gearshift to switch to 5th or 6th gear, the engine...
- P0766S4 stuck OFF malfunction or brake control valve malfunction*: Shifting to 5th and 6th gears is impossible....
- P0776SL2 stuck ON malfunction or brake control valve malfunction*: Shifting to 5th and 6th gears is impossible....
- P0778The ECM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears...
- P0781When conditions (a) and (b), or (a) and (c) are met. (2-trip detection logic) (a) When the ECM directs the...
- P0894The ECM detects a malfunction on SLT, S1, S2, S3, S4, SL2, gear 6 incorrect ratio (sequence valve) or 1-2...
- P0973ECM detects short in solenoid valve S1 circuit 2 times when solenoid valve S1 is operated (1 trip detection...
- P0974ECM detects open in solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated (1 trip...
- P0976ECM detects short in solenoid valve S2 circuit 2 times when solenoid valve S2 is operated (1 trip detection...
- P0977ECM detects open in solenoid valve S2 circuit 2 times when solenoid valve S2 is not operated (1 trip...
- P0979ECM detects short in solenoid valve S3 circuit 2 times when solenoid valve S3 is operated (1 trip detection...
- P0980ECM detects open in solenoid valve S3 circuit 2 times when solenoid valve S3 is not operated (1 trip...
- P0982ECM detects short in solenoid valve S4 circuit 2 times when solenoid valve S4 is operated (1 trip detection...
- P0983ECM detects open in solenoid valve S4 circuit 2 times when solenoid valve S4 is not operated (1 trip...
- P0985ECM detects short in solenoid valve SR circuit 2 times when solenoid valve SR is operated (1 trip detection...
- P0986ECM detects open in solenoid valve SR circuit 2 times when solenoid valve SR is not operated (1 trip...
- P2714The ECM detects a malfunction on SLT (ON side) according to the revolution difference of the turbine and the...
- P2716Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip...
- P2742No. 2 ATF temperature sensor resistance is less than 25 Ω (0.046 V) for 0.5 seconds or more. (1-trip...
- P2743No. 2 ATF temperature sensor resistance is higher than 156 kΩ (4.915 V) for 0.5 sec. or more and either...
- P2757Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h (50 mph)), or lock-up...
- P2759Open or short is detected in shift solenoid valve SLU circuit for 1 second or more while driving (1 trip...
- P2772Transfer 4L position switch remains ON while vehicle is running under following conditions for 1.8 sec. or...
- P2772Transfer 4L position switch remains ON while vehicle is running under following conditions for 1.8 sec. or...
- C1713With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at rear height control sensor RH is...
- C1714With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at rear height control sensor LH is...
- C1715With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at front acceleration sensor RH is...
- C1716With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at front acceleration sensor LH is...
- C1717With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at rear acceleration sensor is...
- C1731When either of the following is detected: · An actuator open-circuit signal is detected for at least 1 second...
- C1732When either of the following is detected: · An actuator open-circuit signal is detected for at least 1 second...
- C1733When either of the following is detected: · An actuator open-circuit signal is detected for at least 1 second...
- C1734When either of the following is detected: · An actuator open-circuit signal is detected for at least 1 second...
- C1745When either of the following is detected: · With the exhaust valve not activated, an open signal of the...
- C1746When either of the following is detected: · With the height control valve inactivated, an open signal of the...
- C1747When either of the following is detected: · With the height control valve inactivated, an open signal of the...
- C1751When either of the following is detected: · With the AIR SUS relay inactivated, an open signal of the AIR SUS...
- C1752When either of the following is detected: · When the power supply voltage is at 12 V or higher, a lock signal...
- C1761Either condition is met: · With the AIR SUS relay activated, the vehicle does not return to the standard...
- C1762With the exhaust valve activated, the vehicle does not go down to the standard vehicle height after 105...
- C1781Suspension control ECU malfunction is detected.
- C1782Terminal IG or B voltage is 10 V or less, or 16 V or more for 0.5 seconds
- C1783Speed sensor circuit malfunction for 1 second or more.
- C1784A steering angle sensor or steering angle sensor power source malfunction signal is detected for 5 seconds or...
- C1787While the ignition switch is ON, a yaw rate and acceleration sensor malfunction signal is detected for 1...
- C1789Either condition is met: · The vehicle identification information is not stored. · The information stored in...
- C1791Absorber control switch signal does not change.
- C1792Height control switch signal does not change.
- C1793Height control mode select switch signal does not change.
- C1796On level surface, G sensor input is +/- 1.96 m/s2 or more for 1 second or more.
- C1797On level surface, G sensor input is +/- 1.96 m/s2 or more for 1 second or more.
- C1798On level surface, G sensor input is +/- 1.96 m/s2 or more for 1 second or more.
- U0100While driving at 30 km/h (19 mph), CAN communication between suspension control ECU and ECM stops for 3...
- U0122CAN communication between suspension control ECU and Skid control ECU stops for 3 seconds or more.
- U0124CAN communication between suspension control ECU and yaw rate and acceleration sensor stops for 3 seconds or...
- U0126CAN communication between suspension control ECU and steering angle sensor stops for 3 seconds or more.
- U0140CAN communication between suspension control ECU and main body ECU stops for 3 seconds or more.
- C2121/21 When all conditions below are met: · Tire pressure warning valve and transmitter is not in stop mode · Signal...
- C2122/22 When all conditions below are met: · Tire pressure warning valve and transmitter is not in stop mode · Signal...
- C2123/23 When all conditions below are met: · Tire pressure warning valve and transmitter is not in stop mode · Signal...
- C2124/24 When all conditions below are met: · Tire pressure warning valve and transmitter is not in stop mode · Signal...
- C2126/26 After ID registration is completed, until all tire pressure warning valve and transmitter IDs are received by...
- C2141/41 The battery of the tire pressure warning valve and transmitter is depleted or G-SW in the tire pressure...
- C2142/42 The battery of the tire pressure warning valve and transmitter is depleted or G-SW in the tire pressure...
- C2143/43 The battery of the tire pressure warning valve and transmitter is depleted or G-SW in the tire pressure...
- C2144/44 The battery of the tire pressure warning valve and transmitter is depleted or G-SW in the tire pressure...
- C2165/65 Temperature inside the tire exceeds 119°C (246.2°F) more than a specified number of times.
- C2166/66 Temperature inside the tire exceeds 119°C (246.2°F) more than a specified number of times.
- C2167/67 Temperature inside the tire exceeds 119°C (246.2°F) more than a specified number of times.
- C2168/68 Temperature inside the tire exceeds 119°C (246.2°F) more than a specified number of times.
- C2171/71 Transmitter ID is not registered (when a transmitter ID is unregistered for 3 minutes or more).
- C2174/74 Vehicle speed signal malfunction
- C2176/76 Malfunction in the tire pressure warning ECU internal circuit.
- C2177/77 When all conditions below are met: · During initialization · Signal is not received from tire pressure...
- C2178/78 With ignition switch ON, when IG voltage of less than 10 V continues for 20 minutes or more, or IG voltage of...
- C2181/81 Test mode procedure is performed.
- C2182/82 Test mode procedure is performed.
- C2183/83 Test mode procedure is performed.
- C2184/84 Test mode procedure is performed.
- C2191/91 Test mode procedure is performed
- C0200/31 When any of following conditions detected: 1. When vehicle speed 15 km/h (9 mph), wheel speed 6 km/h (4 mph)...
- C0205/32 When any of following conditions detected: 1. When vehicle speed 15 km/h (9 mph), wheel speed 6 km/h (4 mph)...
- C0210/33 When any of following conditions detected: 1. When vehicle speed 15 km/h (9 mph), wheel speed 6 km/h (4 mph)....
- C0215/34 When any of following conditions detected: 1. When vehicle speed 15 km/h (9 mph), wheel speed 6 km/h (4 mph)....
- C0226/21 Open or short in solenoid circuit continues for 0.05 seconds or more.
- C0236/22 Open or short in solenoid circuit continues for 0.05 seconds or more.
- C0246/23 Open or short in solenoid circuit continues for 0.05 seconds or more.
- C0256/24 Open or short in solenoid circuit continues for 0.05 seconds or more.
- C0273/13 When one of following conditions is met: 1. Pump motor voltage is 2.0 V or more for 1 sec. or more at motor...
- C0278/11 Either condition is met: 1. Malfunction in skid control ECU continues for 0.056 seconds or more. 2. Voltage...
- C1201/51 Engine control system malfunction signal continues for 1.2 seconds.
- C1203/53 When all of following conditions detected: 1. Engine variation data from ECM does not match one in skid...
- C1207/37 When all conditions below are met: · Yaw rate sensor is normal. · G sensor lateral operation is normal. ·...
- C1225/25 When any of following conditions detected: 1. During switching solenoid (SMC1, SMC2, SRC1 or SRC2) ON signal...
- C1226/26 When any of following conditions detected: 1. During switching solenoid (SMC1, SMC2, SRC1 or SRC2) ON signal...
- C1227/27 When any of following conditions detected: 1. During switching solenoid (SMC1, SMC2, SRC1 or SRC2) ON signal...
- C1228/28 When any of following conditions detected: 1. During switching solenoid (SMC1, SMC2, SRC1 or SRC2) ON signal...
- C1231/31 When any of following conditions detected: 1. The ECU-B1 fuse blows or the ignition switch is turned to ON...
- C1232/32 When any of following conditions detected: 1. Malfunctions in deceleration sensor detected through...
- C1234/34 Sensor malfunction signal received from yaw rate sensor
- C1241/41 When any of following conditions detected: 1. +BS terminal voltage 18 V or more (momentary occurrence...
- C1244/44 G sensor forward and backward operation is malfunctioning (4WD)
- C1247/47 When either condition below is met: 1. When the output becomes 4.7 V or more or 0.2 V or less per 0.1...
- C1249/49 When one of following conditions is met: 1. When voltage of STP2 pin is detected to be outside range of 1.4...
- C1251/51 When any of following conditions detected with normal battery voltage (10 V or more): 1. Open in pump motor...
- C1267/28 When one of following conditions is met: 1. Micro switch signal PSNC and PSNO logic malfunction. 2. When...
- C1271/71 Detected only during test mode.
- C1272/72 Detected only during test mode.
- C1273/73 Detected only during test mode.
- C1274/74 Detected only during test mode.
- C1275/75 Detected only during test mode.
- C1276/76 Detected only during test mode.
- C1277/77 Detected only during test mode.
- C1278/78 Detected only during test mode.
- C1279/79 Detected only during test mode
- C1281/81 Detected only during test mode.
- C1290/66 Steering angle sensor zero point deviates from zero point stored in skid control ECU by 20 degrees or more.
- C1300/62 Malfunction in skid control ECU
- C1310/11 Open or short in active brake booster solenoid circuit.
- C1311/12 Open or short circuit is detected.
- C1330/35 Open in front speed sensor circuit continues for 0.15 seconds or more.
- C1331/36 Open in front speed sensor circuit continues for 0.15 seconds or more.
- C1332/37 Open in rear speed sensor circuit continues for 0.15 seconds or more.
- C1333/38 Open in rear speed sensor circuit continues for 0.15 seconds or more.
- C1336/39 When the vehicle is driven without completion of zero point calibration.
- C1340/47 When the terminal IG1 voltage is between 10 and 14 V, there is an open in the center differential lock...
- C1360/61 When any of the following conditions are detected: 1. When malfunction occurs during pressure sensor initial...
- C1370/73 Information relating to engine, transmission, drivetrain or destination stored in ECM does not match...
- C1380/64
- C1439/66 After the steering angle sensor zero point calibration data is cleared due to, for example, fluctuations in...
- C1445/66 Steering angle sensor zero point is not obtained when the vehicle is driven without a record of steering...
- U0073/94 Bus off conditions continue for approximately 0.8 seconds.
- U0100/65 When CAN signal from ECM is lost or malfunctioning for 1.2 seconds.
- U0114/27 When CAN signal from 4WD control ECU is lost or malfunctioning for 1.2 seconds.
- U0123/62 Supplied voltage normal (9.7 V or more), skid control ECU receives no yaw rate sensor data for 0.1 seconds.
- U0124/69 Supplied voltage normal (9.7 V or more), skid control ECU receives no yaw rate sensor data for 0.1 seconds.
- U0126/63 Supplied voltage normal (9.7 V or more), skid control ECU receives no steering angle sensor data for 0.1...
- C1231An abnormal steering angle signal is received.
- C1531A short or open in the solenoid valve circuit
- C1544An abnormal engine speed signal is received.
- C1547An abnormal vehicle speed signal is received.
- U0073Control module communication bus off.
- B2602When both conditions below are met: · Unlock warning switch signal is OFF. · Ignition switch is turned ON.
- B2603When operating the tilt and telescopic manual switch, an abnormal voltage value is input to the multiplex...
- B2610Tilt operation stops within the operation range while operating.
- B2611Telescopic operation stops within the operation range while operating.
- B2620While the auto away/return function, driving position memory function or manual control is in operation, the...
- B2621Periodical signal from the specified ECU has stopped.
- B2624When either condition below is met: · The auto away function is disabled with the last vehicle speed signal*...
- B1532When either condition below is met: · The stereo component tuner assembly is not connected while the ignition...
- B1551When one of the conditions below is met: · "HD Radio" tuner decoder malfunction · "HD Radio" tuner audio...
- B1552When either of the conditions below is met: · Internal IC malfunction · Tuner malfunction
- B1579Telephone microphone signal is lost.
- B1585USB Device Malfunction · Non mass-storage class or incompatible protocol USB device · USB device with an...
- B158ANoise adjustment is malfunction.
- B158FA video or audio signal is interrupted when the battery voltage drops.
- B15A0When either of the conditions below is met: · Bus malfunction · EEPROM error
- B15B0Picture circuit (TFT unit) malfunction
- B15B3When one of the conditions below is met: · AM tuner PLL is unlocked · FM tuner PLL is unlocked · Tuner...
- B15B4When one of the conditions below is met: · Mechanical communication error · Load/Eject malfunction · Read...
- B15B7"Bluetooth" module malfunction
- B15BAWhen either of the conditions below is met: · Internal IC malfunction · Tuner malfunction
- B15C0Navigation antenna error
- B15C1Error of the power source to the navigation antenna
- B15C3A short is detected in the speaker output circuit.
- B15D5When either condition below is met: · The television display assembly is/was not connected while the ignition...
- B15FESatellite radio antenna is not connected.
- B15FFA short occurs in satellite radio antenna.
- B15A5· Bus or sub-microprocessor malfunction · RAM malfunction · Internal hardware malfunction
- B15D5When either condition below is met: · The television display assembly is/was not connected while the ignition...
- B1532When either condition below is met: · Video signal (digital) is lost. · The stereo component tuner assembly...
- B1551When one of the conditions below is met: · "HD Radio" tuner decoder malfunction · "HD Radio" tuner audio...
- B1579Telephone microphone signal is lost.
- B1585USB Device Malfunction · Non mass-storage class or incompatible protocol USB device · USB device with an...
- B158CThe SD card cannot be mounted when inserted into the SD card slot.
- B158FA video or audio signal is interrupted when the battery voltage drops.
- B15A0When either of the conditions below is met: · Bus malfunction · EEPROM error
- B15A3When one of the conditions below is met: · Internal power supply malfunction · DSP error · EEPROM error
- B15ADWhen one of the conditions below is met: · Short to ground or +B, or open occurs in gyro signal circuit ·...
- B15B0Picture circuit (TFT unit) malfunction
- B15B3When one of the conditions below is met: · AM tuner PLL is unlocked · FM tuner PLL is unlocked · Tuner...
- B15B4When one of the conditions below is met: · Mechanical communication error · Load/Eject malfunction · Read...
- B15B7"Bluetooth" module malfunction
- B15BAWhen either of the conditions below is met: · Internal IC malfunction · Tuner malfunction
- B15C0Navigation antenna error
- B15C1Error of the power source to the navigation antenna
- B15C2A difference between the GPS speed and SPD pulse is detected.
- B15C3A short is detected in the speaker output circuit.
- B15D3When either condition below is met: · Stereo component amplifier assembly is/was not connected while the...
- B15D5A device that is listed in the AVC-LAN network connected device record of the master unit is missing.
- B15FESatellite radio antenna is not connected.
- B15FFA short occurs in satellite radio antenna.
- C1622Open or Short Circuit in rear television camera signal
- C1622Open or Short Circuit in television camera signal
- C1A45A fail flag is transmitted from the skid control ECU.
- C1A47A fail flag is transmitted from the steering angle sensor.
- C1AB0With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage applied...
- C1AB1With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage applied...
- C1AB2With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage output...
- C1AB3With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage output...
- C1AB4With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the current flowing...
- C1AB5With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the current flowing...
- C1AB6The blind spot monitor sensor RH (master) detects an internal malfunction.
- C1AB7The blind spot monitor sensor LH (slave) detects an internal malfunction.
- C1AB8The blind spot monitor sensor cannot communicate with the main body ECU.
- C1ABAThere is an open in the ground circuit (Terminal No. 3) of the blind spot monitor sensor LH for a specified...
- C1ABBA beam axis inspection has not been performed.
- C1ABCA beam axis inspection has not been performed.
- U0100Lost communication with ECM
- U0126Lost communication with steering sensor
- U0129Lost communication with brake system
- U0142Lost communication with main body ECU
- U0232The blind spot monitor sensor RH cannot receive signals from the blind spot monitor sensor LH.
- U0233The blind spot monitor sensor LH cannot receive signals from the blind spot monitor sensor RH.
- U1331Destination information of the main body ECU and blind spot monitor sensor do not match.
- B1206No communication between the master switch and main body ECU for 10 seconds or more.
- B1273No communication between the sliding roof drive gear sub-assembly and main body ECU for 10 seconds or more.
- B1287No communication between the back door ECU and main body ECU for 10 seconds or more.
- B2321No communication between the front power window regulator motor assembly LH and main body ECU for 10 seconds...
- B2322No communication between the front power window regulator motor assembly RH and main body ECU for 10 seconds...
- B2325The main body ECU (cowl side junction block LH) detects a malfunction in the LIN communication bus between...
- B2621Periodic signal from the specified ECU has stopped.
- B2624· The auto away function is disabled with the last vehicle speed signal* at 10 km/h (6 mph) or more. ·...
- U0104There is no communication from the distance control ECU assembly.
- U0199There is no communication from the outer mirror control ECU assembly.
- U0208There is no communication from the front power seat switch LH (power seat control ECU).
- U0230There is no communication from the power back door unit assembly (power back door ECU).
- U0232There is no communication from the blind spot monitor sensor LH.
- U0233There is no communication from the blind spot monitor sensor RH.
- U1002(CAN No. 2 BUS)
- U1002Lost communication with the gateway module (MS bus).
- U1115There is no communication from the multiplex tilt and telescopic ECU.
- B2780The unlock warning switch assembly is not detected as being on when the ignition switch is ON (1 trip...
- B2784The antenna coil in the transponder key coil is open/shorted.
- B2793A transponder chip malfunction (1 trip detection logic*).
- B2794A key with an incomplete key ID code is inserted into the ignition key cylinder (1 trip detection logic*).
- B2795A key with a different vehicle serial number is inserted into the ignition key cylinder (1 trip detection...
- B2796The key ID code cannot be transmitted to the transponder key ECU assembly (1 trip detection logic*).
- B2797A key with a BCC malfunction is inserted into the ignition key cylinder (1 trip detection logic*).
- B2798Key ID code identification cannot be completed within the specified time (1 trip detection logic*).
- B2799One of the following conditions is met: · Error in communication between ECM and transponder key ECU...
- B279ACommunication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
- B279CAn ECM that is incompatible with immobiliser system is installed.
- B1500When combination meter detects fuel sender gauge malfunction
- U0100When either of following conditions is detected: · Vehicle speed 5 km/h (3 mph) or more and IG voltage 10.5 V...
- U0129When either of following conditions is detected: · 15 seconds have elapsed since engine started and IG...
- B1000/31 Center airbag sensor malfunction
- B1610/13 When one of following conditions is met: · Front airbag sensor RH malfunction · Center airbag sensor...
- B1615/14 When one of following conditions is met: · Front airbag sensor LH malfunction · Center airbag sensor...
- B1630/23 When one of following conditions is met: · Rear airbag sensor LH malfunction · Side airbag sensor LH...
- B1635/24 When one of following conditions is met: · Rear airbag sensor RH malfunction · Side airbag sensor RH...
- B1650/32 When one of following conditions is met: · Occupant classification system malfunction · The center airbag...
- B1653/35 When one of following conditions is met: · The center airbag sensor receives a line short circuit signal, an...
- B1655/37 When one of following conditions is met: · The center airbag sensor receives a line short circuit signal, an...
- B1660/43 When one of following conditions is met: · The center airbag sensor receives an open circuit signal, a short...
- B1690/15 When both conditions below are met: · Side airbag sensor LH malfunction · Center airbag sensor malfunction
- B1695/16 When both conditions below are met: · Side airbag sensor RH malfunction · Center airbag sensor malfunction
- B1800/51 When one of following conditions is met: · The center airbag sensor receives a line short circuit signal 5...
- B1801/51 When one of following conditions is met: · The center airbag sensor receives an open circuit signal in the...
- B1802/51 When one of following conditions is met: · The center airbag sensor receives a short circuit to ground signal...
- B1803/51 When one of following conditions is met: · The center airbag sensor receives a short circuit to B+ signal in...
- B1805/52 When one of following conditions is met: · The center airbag sensor receives a line short circuit signal 5...
- B1806/52 When one of following conditions is met: · The center airbag sensor receives an open circuit signal in the...
- B1807/52 When one of following conditions is met: · The center airbag sensor receives a short circuit to ground signal...
- B1808/52 When one of following conditions is met: · The center airbag sensor receives a short circuit to B+ signal in...
- B1810/53 When one of following conditions is met: · The center airbag sensor receives a line short circuit signal 5...
- B1811/53 When one of following conditions is met: · The center airbag sensor receives an open circuit signal in the...
- B1812/53 When one of following conditions is met: · The center airbag sensor receives a short circuit to ground signal...
- B1813/53 When one of following conditions is met: · The center airbag sensor receives a short circuit to B+ signal in...
- B1815/54 When one of following conditions is met: · The center airbag sensor receives a line short circuit signal 5...
- B1816/54 When one of following conditions is met: · The center airbag sensor receives an open circuit signal in the...
- B1817/54 When one of following conditions is met: · The center airbag sensor receives a short circuit to ground signal...
- B1818/54 When one of following conditions is met: · The center airbag sensor receives a short circuit to B+ signal in...
- B181A/7A When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal...
- B181B/7A When one of the following conditions is met: · The center airbag sensor receives an open circuit signal in...
- B181C/7A When one of the following conditions is met: · The center airbag sensor receives a short circuit to ground...
- B181D/7A When one of the following conditions is met: · The center airbag sensor receives a short circuit to B+ signal...
- B1820/55 When one of following conditions is met: · The center airbag sensor receives a line short circuit signal 5...
- B1821/55 When one of following conditions is met: · The center airbag sensor receives an open circuit signal in the...
- B1822/55 When one of following conditions is met: · The center airbag sensor receives a short circuit to ground signal...
- B1823/55 When one of following conditions is met: · The center airbag sensor receives a short circuit to B+ signal in...
- B1825/56 When one of following conditions is met: · The center airbag sensor receives a line short circuit signal 5...
- B1826/56 When one of following conditions is met: · The center airbag sensor receives an open circuit signal in the...
- B1827/56 When one of following conditions is met: · The center airbag sensor receives a short circuit to ground signal...
- B1828/56 When one of following conditions is met: · The center airbag sensor receives a short circuit to B+ signal in...
- B1830/57 When one of following conditions is met: · The center airbag sensor receives a line short circuit signal 5...
- B1831/57 When one of following conditions is met: · The center airbag sensor receives an open circuit signal in the...
- B1832/57 When one of following conditions is met: · The center airbag sensor receives a short circuit to ground signal...
- B1833/57 When one of following conditions is met: · The center airbag sensor receives a short circuit to B+ signal in...
- B1835/58 When one of following conditions is met: · The center airbag sensor receives a line short circuit signal 5...
- B1836/58 When one of following conditions is met: · The center airbag sensor receives an open circuit signal in the...
- B1837/58 When one of following conditions is met: · The center airbag sensor receives a short circuit to ground signal...
- B1838/58 When one of following conditions is met: · The center airbag sensor receives a short circuit to B+ signal in...
- B1860/64 When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal...
- B1861/64 When one of the following conditions is met: · The center airbag sensor receives an open circuit signal in...
- B1862/64 When one of the following conditions is met: · The center airbag sensor receives a short circuit to ground...
- B1863/64 When one of the following conditions is met: · The center airbag sensor receives a short circuit to B+ signal...
- B1865/65 When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal...
- B1866/65 When one of the following conditions is met: · The center airbag sensor receives an open circuit signal in...
- B1867/65 When one of the following conditions is met: · The center airbag sensor receives a short circuit to ground...
- B1868/65 When one of the following conditions is met: · The center airbag sensor receives a short circuit to B+ signal...
- B1900/73 When one of following conditions is met: · The center airbag sensor receives a line short circuit signal 5...
- B1901/73 When one of following conditions is met: · The center airbag sensor receives an open circuit signal in the...
- B1902/73 When one of following conditions is met: · The center airbag sensor receives a short circuit to ground signal...
- B1903/73 When one of following conditions is met: · The center airbag sensor receives a short circuit to B+ signal in...
- B1905/74 When one of following conditions is met: · The center airbag sensor receives a line short circuit signal 5...
- B1906/74 When one of following conditions is met: · The center airbag sensor receives an open circuit signal in the...
- B1907/74 When one of following conditions is met: · The center airbag sensor receives a short circuit to ground signal...
- B1908/74 When one of following conditions is met: · The center airbag sensor receives a short circuit to B+ signal in...
- B1771One of following conditions is met: · Occupant classification ECU detects line short circuit signal, open...
- B1780One of following conditions is met: · Occupant classification ECU receives line short circuit signal, open...
- B1781One of following conditions is met: · Occupant classification ECU receives line short circuit signal, open...
- B1782One of following conditions is met: · Occupant classification ECU receives line short circuit signal, open...
- B1783One of following conditions is met: · Occupant classification ECU receives line short circuit signal, open...
- B1785Either of following conditions is met: · Occupant classification ECU receives collision detection signal,...
- B1786Either of following conditions is met: · Occupant classification ECU receives collision detection signal,...
- B1787Either of following conditions is met: · Occupant classification ECU receives collision detection signal,...
- B1788Either of following conditions is met: · Occupant classification ECU receives collision detection signal,...
- B1790One of following conditions is met: · Occupant classification ECU receives line short circuit signal, open...
- B1793One of following conditions is met: · Occupant classification ECU receives line short circuit signal, open...
- B1794One of following conditions is met: · Occupant classification ECU circuit malfunction · Occupant...
- B1795Occupant classification ECU malfunction
- B1796Occupant classification ECU malfunction
- B1411/11 Open or short in room temperature sensor circuit
- B1412/12 Open or short in ambient temperature sensor circuit
- B1413/13 Open or short in evaporator temperature sensor circuit
- B1417/17 Open or short in rear evaporator temperature sensor circuit
- B1419/19 Open or short in rear room temperature sensor circuit
- B1421/21 Open or short in passenger side solar sensor circuit
- B1422/22 Open or short in compressor lock sensor circuit
- B1423/23 · Open or short in pressure sensor circuit · Refrigerant pressure on the high pressure side is extremely low...
- B1424/24 Open or short in driver side solar sensor circuit
- B1441/41 Air mix damper position sensor value does not change even if air conditioning amplifier operates air mix...
- B1442/42 Recirculation damper position sensor value does not change even if air conditioning amplifier operated...
- B1443/43 Air outlet damper position sensor value does not change even if air conditioning amplifier operates air...
- B1445/45 Cool air bypass servo motor position sensor value does not change even if air conditioning amplifier operates...
- B1446/46 Air mix damper position sensor value does not change even if air conditioning amplifier operates air mix...
- B1447/47 Rear air mix damper position does not change even if air conditioning amplifier operates rear air mix damper...
- B1449/49 Mode rear damper position does not change even if air conditioning amplifier operates rear air outlet damper...
- B1497/97 Communication line error or open
- B1499/99 Open in CAN communication circuit
- B2221· PLS1 pulse sensor circuit malfunction · PLS2 pulse sensor circuit malfunction · Pulse direction is opposite...
- B2311When either condition below is met: 1. The power window regulator motor malfunctions. 2. When the ECU in the...
- B2312· The power window regulator master switch is stuck. · The power window regulator master switch is held in...
- B2313· The power window regulator motor is not initialized. · The power window regulator motor malfunctions.
- B2341Sensor (Motor) Failure
- B2342Sliding roof drive gear (sliding roof ECU) detects that SLIDE or TILT switch in roof console box is stuck for...
- B2343Sliding roof drive gear (sliding roof ECU) has not been initialized
- B2344Position Failure
- B2250While back door closer is operating, malfunction is detected in position information from sector switch...
- B2251While back door closer is operating, malfunction is detected in position information from each switch within...
Common jobs · 3UR-FE (14)
- Read / clear codes
- Engine oil & filter: replacement
- Ignition coil: removal · installation
- Drive belt: on-vehicle inspection · removal · installation
- Coolant: replacement
- Water pump: on-vehicle inspection · removal · installation
- Thermostat: inspection · removal · installation
- Radiator: on-vehicle inspection · removal · disassembly · reassembly · installation
- Fuel pump: inspection · disassembly · reassembly
- Injectors: inspection · removal · installation
- Throttle body: on-vehicle inspection · inspection · removal · installation
- Cylinder head gasket: removal
- Engine assembly: on-vehicle inspection · inspection · removal · disassembly · reassembly · installation
- Starter: inspection · removal · disassembly · reassembly · installation
Common jobs · 3UR-FBE (14)
- Read / clear codes
- Engine oil & filter: replacement
- Ignition coil: removal · installation
- Drive belt: on-vehicle inspection · removal · installation
- Coolant: replacement
- Water pump: on-vehicle inspection · removal · installation
- Thermostat: inspection · removal · installation
- Radiator: on-vehicle inspection · removal · disassembly · reassembly · installation
- Fuel pump: inspection
- Injectors: inspection · removal · installation
- Throttle body: on-vehicle inspection · inspection · removal · installation
- Cylinder head gasket: removal
- Engine assembly: on-vehicle inspection · inspection · removal · disassembly · reassembly · installation
- Starter: inspection · removal · disassembly · reassembly · installation
Common jobs · chassis & body (10)
- Alternator: inspection · removal · disassembly · reassembly · installation
- ATF: adjustment
- Front brakes: inspection · removal · disassembly · reassembly · installation
- Rear brakes: inspection · removal · disassembly · reassembly · installation
- Brake fluid: on-vehicle inspection · replacement · bleeding
- Parking brake: inspection · disassembly · reassembly
- Wheel alignment: adjustment
- Front drive shaft: removal · disassembly · reassembly · installation
- Headlights: removal · disassembly · reassembly · installation · adjustment
- A/C refrigerant: on-vehicle inspection · replacement
Repair Manual
General305 documents
Engine / Hybrid System789 documents
Drivetrain337 documents
Suspension165 documents
Brake137 documents
Steering85 documents
Audio / Visual / Telematics317 documents
Power Source / Network77 documents
Vehicle Interior744 documents
Vehicle Exterior443 documents