Home › General › INTRODUCTION › WHEN REMOVING,INSTALLING OR REPLACING PARTS
BM27L0U _V1 General _049512 INTRODUCTION _0249517 WHEN REMOVING,INSTALLING OR REPLACING PARTS F

INTRODUCTION  WHEN REMOVING,INSTALLING OR REPLACING PARTS  WHEEL ALIGNMENT STANDARD  


NOTICE:

For vehicles equipped with VSC, if the wheel alignment has been adjusted, or if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:

1.

Disconnect the cable from the negative (-) battery terminal for more than 2 seconds.

2.

Reconnect the cable to the negative (-) battery terminal.

3.

Perform zero point calibration of the yaw rate and deceleration sensor, and test mode inspection.



MEASURE VEHICLE HEIGHT


NOTICE:

Before inspecting the wheel alignment, adjust the vehicle height to the specification.


a.
C180789E02
0.053,0.008 0.298,0.213 0.245,0.205 10 *a 0.062,2.449 0.287,2.653 0.226,0.205 10 *b 3.035,1.624 3.198,1.815 0.163,0.191 10 A 1.385,1.615 1.569,1.813 0.184,0.198 10 B 0.861,4.056 1.017,4.240 0.156,0.184 10 D 2.889,4.065 3.059,4.234 0.170,0.170 10 C

Press down on the vehicle several times to stabilize the suspension, and then measure the vehicle height.

Text in Illustration
*a Front Side
*b Rear Side

Measuring points:
A:

Ground clearance of the front drive shaft center

B:

Ground clearance of the front adjusting cam bolt center

C:

Ground clearance of the rear drive shaft center

D:

Ground clearance of the rear lower arm No. 1 adjusting cam bolt center


Standard Vehicle Height (Unloaded Vehicle):
Vehicle Model Tire Size Front A - B Rear C - D
USK60L-GKTSKA P275/65R18 8JJ 108.1 mm (4.26 in.) 30.3 mm (1.19 in.)
P275/55R20 8JJ 108.1 mm (4.26 in.) 30.3 mm (1.19 in.)
USK60L-GKTLKA P275/65R18 8JJ 107.6 mm (4.24 in.) 30.6 mm (1.20 in.)
P275/55R20 8JJ 107.6 mm (4.24 in.) 30.6 mm (1.20 in.)
USK60L-GKTZKA P275/55R20 8JJ 106.6 mm (4.20 in.) 39.1 mm (1.54 in.)
USK65L-GKTSKA P275/65R18 8JJ 101.9 mm (4.01 in.) 25.2 mm (0.99 in.)
P275/55R20 8JJ 101.9 mm (4.01 in.) 25.2 mm (0.99 in.)
USK65L-GKTLKA P275/65R18 8JJ 101.7 mm (4.00 in.) 25.3 mm (1.00 in.)
P275/55R20 8JJ 101.7 mm (4.00 in.) 25.3 mm (1.00 in.)
USK65L-GKTZKA P275/55R20 8JJ 100.3 mm (3.95 in.) 34.0 mm (1.34 in.)
USK65L-GKTSGA P275/65R18 8JJ 101.9 mm (4.01 in.) 25.2 mm (0.99 in.)
P275/55R20 8JJ 101.9 mm (4.01 in.) 25.2 mm (0.99 in.)
USK65L-GKTLGA P275/65R18 8JJ 101.7 mm (4.00 in.) 25.3 mm (1.00 in.)
P275/55R20 8JJ 101.7 mm (4.00 in.) 25.3 mm (1.00 in.)
USK65L-GKTZGA P275/55R20 8JJ 100.3 mm (3.95 in.) 34.0 mm (1.34 in.)


NOTICE:

The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.




INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION (FRONT WHEEL ALIGNMENT)


Z003382E32
2.563,0.917 2.823,0.896 false 1.115,1.438 0.833,1.135 false 0.646,1.052 0.823,1.219 0.177,0.167 10 false *1 2.854,0.802 3.052,0.969 0.198,0.167 10 false *2

a.

Install a camber-caster-kingpin gauge or place the front wheels on the center of a wheel alignment tester.

Text in Illustration
*1 Wheel Alignment Tester
*2 Gauge


b.

Inspect the camber, caster and steering axis inclination.

Standard Camber, Caster, Steering Axis Inclination (Unloaded Vehicle):
Vehicle Model Tire Size Camber Inclination Caster Inclination Steering Axis Inclination
USK60L-GKTSKA P275/65R18 8JJ -0°10' +/-45'
(-0.17° +/-0.75°)
3°46' +/-45'
(3.76° +/-0.75°)
13°11' +/-45'
(13.19° +/-0.75°)
P275/55R20 8JJ -0°10' +/-45'
(-0.17° +/-0.75°)
3°46' +/-45'
(3.76° +/-0.75°)
13°11' +/-45'
(13.19° +/-0.75°)
USK60L-GKTLKA P275/65R18 8JJ -0°10' +/-45'
(-0.16° +/-0.75°)
3°46' +/-45'
(3.77° +/-0.75°)
13°11' +/-45'
(13.18° +/-0.75°)
P275/55R20 8JJ -0°10' +/-45'
(-0.16° +/-0.75°)
3°46' +/-45'
(3.77° +/-0.75°)
13°11' +/-45'
(13.18° +/-0.75°)
USK60L-GKTZKA P275/55R20 8JJ -0°09' +/-45'
(-0.15° +/-0.75°)
3°56' +/-45'
(3.94° +/-0.75°)
13°10' +/-45'
(13.17° +/-0.75°)
USK65L-GKTSKA P275/65R18 8JJ -0°01' +/-45'
(-0.02° +/-0.75°)
3°38' +/-45'
(3.64° +/-0.75°)
13°03' +/-45'
(13.05° +/-0.75°)
P275/55R20 8JJ -0°01' +/-45'
(-0.02° +/-0.75°)
3°35' +/-45'
(3.59° +/-0.75°)
13°03' +/-45'
(13.05° +/-0.75°)
USK65L-GKTLKA P275/65R18 8JJ -0°01' +/-45'
(-0.01° +/-0.75°)
3°39' +/-45'
(3.65° +/-0.75°)
13°03' +/-45'
(13.05° +/-0.75°)
P275/55R20 8JJ -0°01' +/-45'
(-0.01° +/-0.75°)
3°35' +/-45'
(3.59° +/-0.75°)
13°03' +/-45'
(13.05° +/-0.75°)
USK65L-GKTZKA P275/55R20 8JJ 0°00' +/-45'
(0.00° +/-0.75°)
3°46' +/-45'
(3.76° +/-0.75°)
13°02' +/-45'
(13.03° +/-0.75°)
USK65L-GKTSGA P275/65R18 8JJ -0°01' +/-45'
(-0.02° +/-0.75°)
3°38' +/-45'
(3.64° +/-0.75°)
13°03' +/-45'
(13.05° +/-0.75°)
P275/55R20 8JJ -0°01' +/-45'
(-0.02° +/-0.75°)
3°35' +/-45'
(3.59° +/-0.75°)
13°03' +/-45'
(13.05° +/-0.75°)
USK65L-GKTLGA P275/65R18 8JJ -0°01' +/-45'
(-0.01° +/-0.75°)
3°39' +/-45'
(3.65° +/-0.75°)
13°03' +/-45'
(13.05° +/-0.75°)
P275/55R20 8JJ -0°01' +/-45'
(-0.01° +/-0.75°)
3°35' +/-45'
(3.59° +/-0.75°)
13°03' +/-45'
(13.05° +/-0.75°)
USK65L-GKTZGA P275/55R20 8JJ 0°00' +/-45'
(0.00° +/-0.75°)
3°46' +/-45'
(3.76° +/-0.75°)
13°02' +/-45'
(13.03° +/-0.75°)




INSPECT TOE-IN (FRONT WHEEL ALIGNMENT)


A166181E11
1.664,0.297 1.776,0.455 0.112,0.158 10 A 1.637,0.759 1.852,0.918 0.215,0.158 10 *a 1.662,1.956 1.774,2.114 0.112,0.158 10 B

a.

Bounce the vehicle up and down at the corners to stabilize the suspension, and then inspect the toe-in.

Text in Illustration
*a Front of the Vehicle

Standard Toe-in (Unloaded Vehicle):
Vehicle Model Tire Size B - A
USK60L-GKTSKA P275/65R18 8JJ 2.15 mm (0.0847 in.)
P275/55R20 8JJ 2.15 mm (0.0847 in.)
USK60L-GKTLKA P275/65R18 8JJ 2.27 mm (0.0894 in.)
P275/55R20 8JJ 2.27 mm (0.0894 in.)
USK60L-GKTZKA P275/55R20 8JJ 2.36 mm (0.0929 in.)
USK65L-GKTSKA P275/65R18 8JJ 2.31 mm (0.0909 in.)
P275/55R20 8JJ 2.31 mm (0.0909 in.)
USK65L-GKTLKA P275/65R18 8JJ 2.36 mm (0.0929 in.)
P275/55R20 8JJ 2.36 mm (0.0929 in.)
USK65L-GKTZKA P275/55R20 8JJ 2.53 mm (0.0996 in.)
USK65L-GKTSGA P275/65R18 8JJ 2.31 mm (0.0909 in.)
P275/55R20 8JJ 2.31 mm (0.0909 in.)
USK65L-GKTLGA P275/65R18 8JJ 2.36 mm (0.0929 in.)
P275/55R20 8JJ 2.36 mm (0.0929 in.)
USK65L-GKTZGA P275/55R20 8JJ 2.53 mm (0.0996 in.)


If the toe-in is not as specified, adjust it at the rack ends.




INSPECT WHEEL ANGLE (FRONT WHEEL ALIGNMENT)


a.
C132439E14
2.718,0.15 2.901,0.327 0.184,0.176 10 *a 2.383,0.15 2.567,0.327 0.184,0.176 10 *b 0.512,0.15 0.696,0.327 0.184,0.176 10 *a 0.843,0.15 1.027,0.327 0.184,0.176 10 *b 1.634,0.657 1.827,0.834 0.194,0.176 10 *c

Turn the steering wheel to the left and right to the full lock positions and measure the turning angle.

Text in Illustration
*a Inside
*b Outside
*c Front of the Vehicle

Standard Wheel Angle (Unloaded Vehicle):
Vehicle Model Tire Size Inside Wheel Angle Outside Wheel Angle (Reference)
USK60L-GKTSKA P275/65R18 8JJ -40°59' (-40.99°) 36°22' (36.36°)
P275/55R20 8JJ -40°59' (-40.99°) 36°22' (36.36°)
USK60L-GKTLKA P275/65R18 8JJ -41°00' (-41.00°) 36°23' (36.38°)
P275/55R20 8JJ -41°00' (-41.00°) 36°23' (36.38°)
USK60L-GKTZKA P275/55R20 8JJ -41°01' (-41.01°) 36°23' (36.39°)
USK65L-GKTSKA P275/65R18 8JJ -41°17' (-41.28°) 36°24' (36.40°)
P275/55R20 8JJ -41°17' (-41.28°) 36°24' (36.40°)
USK65L-GKTLKA P275/65R18 8JJ -41°17' (-41.28°) 36°25' (36.41°)
P275/55R20 8JJ -41°17' (-41.28°) 36°25' (36.41°)
USK65L-GKTZKA P275/55R20 8JJ -41°17' (-41.29°) 36°26' (36.43°)
USK65L-GKTSGA P275/65R18 8JJ -41°17' (-41.28°) 36°24' (36.40°)
P275/55R20 8JJ -41°17' (-41.28°) 36°24' (36.40°)
USK65L-GKTLGA P275/65R18 8JJ -41°17' (-41.28°) 36°25' (36.41°)
P275/55R20 8JJ -41°17' (-41.28°) 36°25' (36.41°)
USK65L-GKTZGA P275/55R20 8JJ -41°17' (-41.29°) 36°26' (36.43°)




INSPECT CAMBER (REAR WHEEL ALIGNMENT)


C107736E01
2.295,0.657 2.739,0.819 0.444,0.162 10 Gauge 2.033,1.261 2.15,0.77 2.15,0.77 2.25,0.77 false

a.

Install a camber-caster-kingpin gauge or put the wheels on a wheel alignment tester.


b.

Inspect the camber.

Standard Camber Inclination (Unloaded Vehicle):
Drive Type Rear Suspension Type Camber Inclination
2WD Coil -1°25' +/-45'
(-1.42°+/-0.75°)
Air -1°41' +/-45'
(-1.68°+/-0.75°)
4WD Coil -1°17' +/-45'
(-1.28°+/-0.75°)
Air -1°33' +/-45'
(-1.55°+/-0.75°)


If the measured value is not within the specified range, inspect the suspension parts for damage and wear. Replace parts as necessary because camber cannot be properly adjusted with any damaged or worn parts.




INSPECT TOE-IN (REAR WHEEL ALIGNMENT)


U154221E02
0.302,0.042 0.438,0.188 0.135,0.146 10 false A 1.698,1.917 1.833,2.063 0.135,0.146 10 false B 1.625,0.115 1.76,0.26 0.135,0.146 10 false C 1.49,0.5 1.854,0.667 0.365,0.167 10 false Front 3.073,0.031 3.208,0.177 0.135,0.146 10 false A

Standard toe-in (Unloaded Vehicle):
Drive Type Rear Suspension Type Specified Condition
2WD Coil A: -0°02' +/-4' (-0.03°+/-0.07°)
B - C: -1.0 +/-2 mm (-0.0394 +/-0.0787 in.)
Air A: -0°01' +/-4' (-0.02°+/-0.07°)
B - C: -0.3 +/-2 mm (-0.0118 +/-0.0787 in.)
4WD Coil A: -0°03' +/-4' (-0.05°+/-0.07°)
B - C: -1.4 +/-2 mm (-0.0551 +/-0.0787 in.)
Air A: -0°02' +/-4' (-0.03°+/-0.07°)
B - C: -0.7 +/-2 mm (-0.0276 +/-0.0787 in.)


If the toe-in is not within the specified range, inspect the suspension parts and replace if necessary.