Home › General › ENGINE › 3UR-FE ENGINE
NM27L0U _V1 General _050238 ENGINE _0242542 3UR-FE ENGINE UN GENERAL/CONTROL/DETAILS F

ENGINE  3UR-FE ENGINE  GENERAL/CONTROL/DETAILS  INTAKE AND EXHAUST SYSTEM  


General


a.

A linkless-type throttle body is used and it realizes excellent throttle control.


b.

The Electronic Throttle Control System-intelligent (ETCS-i) is used to ensure excellent throttle control in all operating ranges.


c.

The Acoustic Control Induction System (ACIS) is used to improve the engine performance in all speed ranges.


d.

A plastic intake manifold is used.


e.

Stainless steel exhaust manifolds and exhaust pipes are used.

W132001C01
1.927,2.479 1.646,0.677 true 1.146,2.188 0.729,1.01 true 0.479,3.615 1.385,2.604 true 0.906,4.083 1.583,2.813 true 1.542,4.406 2.021,3.083 true 3.521,4.302 3.135,3.292 true 4.365,4.063 3.719,2.896 true 6.167,3.604 5.344,2.323 true 3.375,0.49 2.781,2.969 true 1.531,0.458 1.844,0.615 0.313,0.156 10 false *1 0.604,0.833 0.917,0.99 0.313,0.156 10 false *2 0.302,3.656 0.615,3.813 0.313,0.156 10 false *3 0.729,4.104 1.042,4.26 0.313,0.156 10 false *4 1.427,4.448 1.74,4.604 0.313,0.156 10 false *5 3.479,4.344 3.792,4.5 0.313,0.156 10 false *6 4.375,4.146 4.688,4.302 0.313,0.156 10 false *7 6.156,3.646 6.469,3.802 0.313,0.156 10 false *8 3.313,0.302 3.625,0.458 0.313,0.156 10 false *9
*1 Intake Manifold *2 Air Cleaner
*3 Throttle Body *4 Exhaust Manifold RH
*5 Exhaust Manifold LH *6 Front Exhaust Pipe LH
*7 Center Exhaust Pipe *8 Tailpipe
*9 Front Exhaust Pipe RH - -




Throttle Body


a.

A linkless-type throttle body in which the throttle position sensor and the throttle control motor are integrated is used. It realizes excellent throttle valve control.


b.

For a throttle control motor, a DC motor with excellent response and minimal power consumption is used. The ECM performs duty cycle control of the direction and the amperage of the current that is supplied to the throttle control motor in order to regulate the throttle valve angle.

W128398C01
4.646,1.125 5.177,0.979 true 3.073,0.688 2.677,0.24 true 3.354,2.219 2.958,2.542 true 2.521,0.104 2.771,0.333 0.25,0.229 10 false *1 2.813,2.5 3.063,2.729 0.25,0.229 10 false *2 5.188,0.875 5.438,1.104 0.25,0.229 10 false *3
*1 Throttle Valve *2 Throttle Control Motor
*3 Throttle Position Sensor Portion - -




Intake Manifold


a.

An intake manifold with a built-in plastic intake air chamber is used for weight reduction.


b.

The port diameter and length are optimized to achieve high torque in all driving ranges.


c.

The intake manifold contains valves for the Acoustic Control Induction System (ACIS), and the actuator is laser-welded to the intake manifold.

W128399C01
1.708,1.198 1.396,0.573 true 1.771,1.094 1.771,0.51 true 4.26,1.26 4.26,0.677 true 5.563,2.125 5.521,1.49 true 4.5,3.417 4.229,3.063 true 1.26,0.396 1.49,0.625 0.229,0.229 10 false *1 1.708,0.333 1.938,0.563 0.229,0.229 10 false *2 4.198,0.49 4.427,0.719 0.229,0.229 10 false *3 0.302,1.958 0.531,2.188 0.229,0.229 10 false *a 6.698,0.615 6.927,0.844 0.229,0.229 10 false *a 4.5,3.438 4.729,3.667 0.229,0.229 10 false *4 5.51,2.146 5.74,2.375 0.229,0.229 10 false *5
*1 Left Bank Passage *2 Right Bank Passage
*3 ACIS Actuator *4 Laser-welding
*5 Intake Air Control Valve - -
*a Front - -


HINT:
Laser-welding:

In laser-welding, a laser-absorbing material (for the intake manifold) is joined to a laser-transmitting material (for the ACIS actuator). Laser beams are then irradiated from the laser-transmitting side. The beams penetrate the laser-transmitting material to heat and melt the surface of the laser-absorbing material. Then, the heat of the laser-absorbing material melts the laser-transmitting material and causes both materials to become welded.




Exhaust Manifold


a.

A stainless steel exhaust manifold is used for weight reduction and rust resistance.


b.

The exhaust manifold for each bank uses a semi-dual structure (a 4-2-1 grouping). This structure combines the 4 exhaust ports of one bank into 2 groups, then the 2 groups into 1 group, before the exhaust pipe. This reduces exhaust gas interference and improves power output.


c.

The exhaust manifold heat insulator is made of corrugated aluminum. This ensures rigidity, and at the same time, increases the surface area to improve heat dissipation. Furthermore, a floating construction is used at the tightened area to reduce the transfer of heat and vibration to the heat insulator and improve reliability.


d.

Along with the adoption of the air injection system, air injection pipes are provided for the right and left bank exhaust manifolds.

W128400C01
2,4.563 3.323,3.406 true 1.281,3.031 1.281,2.594 true 3.49,3.135 3.49,1.865 true 4.927,3.823 5.302,2.281 true 5.271,4.063 5.75,3.448 true 5.948,4.438 6.229,4 true 1.448,0.5 1.688,0.719 0.24,0.219 10 false *a 1.469,1.448 1.708,1.667 0.24,0.219 10 false *b 1.219,3.052 1.479,3.281 0.26,0.229 10 false *1 1.823,4.531 2.083,4.76 0.26,0.229 10 false *2 3.438,1.688 3.698,1.917 0.26,0.229 10 false *5 5.26,2.104 5.542,2.354 0.281,0.25 10 false *5 5.729,3.281 5.99,3.51 0.26,0.229 10 false *4 6.208,3.823 6.469,4.052 0.26,0.229 10 false *3 5.625,5.448 5.885,5.677 0.26,0.229 10 false *c 5.625,6.063 5.885,6.292 0.26,0.229 10 false *d
*1 Heat Insulator RH *2 Exhaust Manifold RH
*3 Heat Insulator LH *4 Exhaust Manifold LH
*5 Air Injection Pipe - -
*a Floating Construction *b Heat Insulator Tightened Area Cross Section
*c Corrugated *d Heat Insulator Cross Section




Exhaust Pipe


a.

General

i.

The exhaust pipes are made of stainless steel to reduce their weight and improve rust resistance.


ii.

A 2-way exhaust control system is provided in the muffler.


iii.

Two ceramic type Three-Way Catalytic converters (TWCs) are provided in the front exhaust pipe for the right bank and also two for the left bank. As a result, exhaust emission performance of the engine is improved.

W132002C01
1.594,1.594 1.24,1.125 true 1.906,2.365 2.135,2.042 true 2.448,2.469 2.51,2.208 true 3.219,2.365 3.125,2.052 true 1.99,1.719 1.906,0.969 true 2.594,1.563 2.51,0.813 true 3.854,2.229 3.417,1.594 true 4.948,1.76 4.385,1.094 true 6,1.417 5.583,1 true 4.344,2.073 3.906,1.531 true 1.792,2.385 2.104,2.542 0.313,0.156 10 false *2 1.094,0.958 1.406,1.115 0.313,0.156 10 false *1 2.365,2.5 2.677,2.656 0.313,0.156 10 false *3 3.177,2.438 3.49,2.594 0.313,0.156 10 false *3 1.823,0.74 2.135,0.896 0.313,0.156 10 false *3 2.438,0.583 2.75,0.74 0.313,0.156 10 false *3 3.896,2.271 4.208,2.427 0.313,0.156 10 false *4 4.375,2.135 4.688,2.292 0.313,0.156 10 false *5 4.969,1.792 5.281,1.948 0.313,0.156 10 false *6 6.052,1.438 6.365,1.594 0.313,0.156 10 false *7
*1 Front Exhaust Pipe RH *2 Front Exhaust Pipe LH
*3 TWC *4 Center Exhaust Pipe
*5 Main Muffler *6 Tailpipe
*7 Sub Muffler - -




b.

2-way Exhaust Control System

i.

General

·

2-way exhaust control system reduces the back pressure by opening and closing a control valve that is enclosed in the main muffler, thus varying the exhaust gas pressure.

·

The control valve opens steplessly in accordance with the operating condition of the engine, thus enabling a quieter operation at lower engine speeds, and reducing back pressure at higher engine speeds.

·

The back pressure overcomes the spring force of the control valve. The control valve opens steplessly in accordance with the exhaust gas pressure.



ii.

Operation

1.

When Control Valve is Closed (Low Engine Speed)

Since the pressure in the main muffler is low, the control valve is closed. Hence exhaust gas does not pass the bypass, and exhaust noise is decreased in the main muffler.

W128402C01
3.031,1.063 2.854,0.531 true 3.26,2.26 3.083,1.729 true 1.802,1.021 2.021,1.24 0.219,0.219 10 false *a 1.813,1.573 2.031,1.792 0.219,0.219 10 false *a 2.76,0.333 2.979,0.552 0.219,0.219 10 false *b 3.24,2.281 3.458,2.5 0.219,0.219 10 false *b
*a Exhaust Gas *b Control Valve Closed



2.

When Control Valve is Open (Middle to High Engine Speed)

The valve opens as the engine speed and the back pressure in the main muffler increase. This allows a large volume of exhaust gas to pass the bypass, thereby substantially decreasing the back pressure.

W128403C01
3.083,1.042 2.969,0.479 true 3.375,2.271 3.167,1.771 true 1.802,1.031 2.021,1.26 0.219,0.229 10 false *a 1.802,1.604 2.021,1.833 0.219,0.229 10 false *a 2.865,0.313 3.083,0.542 0.219,0.229 10 false *b 3.375,2.281 3.594,2.51 0.219,0.229 10 false *b
*a Exhaust Gas *b Control Valve Open