ULTRASONIC SENSOR
Each ultrasonic sensor transmits ultrasonic waves, receives the reflected waves from an obstacle, and transmits a signal to the clearance warning ECU regarding the distance to the obstacle.
The frequency used by the ultrasonic sensors varies as shown below, depending on the installation position of the ultrasonic sensors.
| Ultrasonic Sensor | Frequency |
|---|---|
| Front & Rear Corner | 45.7 kHz |
| Back | 58.8 kHz |
BUZZER
The ON/OFF times of the buzzer vary in accordance with the distance to the obstacle as shown in the following table:
| Detection Area | Detection Distance | mm (in.) | Buzzer ON/OFF Time (msec.) | ||
|---|---|---|---|---|---|
| ON | OFF | ||||
| Front Corner | Long | 600 +/- 60 to 400 +/- 40
(23.6 +/- 2.4 to 15.7 +/- 1.6) |
150 +/- 15 | 150 +/- 15 | |
| Middle | 400 +/- 40 to 250 +/- 30
(15.7 +/- 1.6 to 9.8 +/- 1.1) |
75 +/- 7.5 | 75 +/- 7.5 | ||
| Short | 250 +/- 30 or less
(9.8 +/- 1.1 or less) |
Continuous | 0 | ||
| Rear Corner | Long | 850 +/- 90 to 520 +/- 60
(33.5 +/- 3.4 to 20.5 +/- 2.4) |
150 +/- 15 | 150 +/- 15 | |
| Short | 520 +/- 60 to 400 +/- 40
(20.5 +/- 2.4 to 15.7 +/- 1.6) |
75 +/- 7.5 | 75 +/- 7.5 | ||
| Middle | 400 +/- 40 or less
(15.7 +/- 1.6 or less) |
Continuous | 0 | ||
| Back | Long | 1800 +/- 180 to 1150 +/- 120
(70.9 +/- 7.1 to 45.7 +/- 4.6) |
150 +/- 15 | 150 +/- 15 | |
| Middle | 1150 +/- 120 to 850 +/- 90
(45.7 +/- 4.6 to 33.5 +/- 3.4) |
75 +/- 7.5 | 75 +/- 7.5 | ||
| Short | 850 +/- 90 or less
(33.5 +/- 3.4 or less) |
Continuous | 0 | ||
The following table indicates the changes in buzzer beeping patterns depending on obstacle detection. It also shows the pattern changes in regard to detection by both front ultrasonic sensors and rear ultrasonic sensors.
| Front | Short | Middle | Long | Not detected | |
|---|---|---|---|---|---|
| Rear | Short | Timing 1 | Timing 2 | Timing 2 | Continuous Beep |
| Middle | Timing 2 | 0.15 sec. | 0.15 sec. | 0.15 sec. | |
| Long | Timing 2 | 0.15 sec. | 0.3 sec. | 0.3 sec. | |
| Not detected | Continuous Beep | 0.15 sec. | 0.3 sec. | No Beep | |
CLEARANCE SONAR ECU
The clearance warning ECU effects overall control of the system, including the switching of the transmitting and reception of the ultrasonic sensor signals, processing the received wave signals, determining the presence of obstacles, actuating the buzzer, and determining the presence of a malfunction in the sensors.
The sound volume of the buzzer in the accessory meter can be adjusted at the clearance warning ECU.
| *1 | Buzzer Sound Volume Adjustment Screw | - | - |