Home › General › ENGINE › 3UR-FBE ENGINE › 2015.08–2016.10
NM27L0U _V1 General _050238 ENGINE _0243247 3UR-FBE ENGINE UN GENERAL/CONTROL/DETAILS F

ENGINE  3UR-FBE ENGINE  GENERAL/CONTROL/DETAILS  VALVE MECHANISM  


General


a.

Each cylinder of this engine has 2 intake valves and 2 exhaust valves. Intake and exhaust efficiency is increased due to the larger areas of all the ports.


b.

This engine uses roller rocker arms with built-in needle bearings. This reduces the friction that occurs between the cams and the valve rocker arm sub-assemblies that push the valves down, thus improving fuel economy.


c.

Valve lash adjuster assemblies, which maintain a constant zero valve clearance through the use of oil pressure and spring force, are used.


d.

To ensure highly accurate valve timing, separate primary timing chains are driven by the crankshaft in order to rotate the intake camshafts of the left and right banks. The exhaust camshafts are driven by the intake camshaft of the respective bank via secondary timing chains.


e.

This engine has a Dual Variable Valve Timing-intelligent (VVT-i) system which controls the intake and exhaust camshafts to provide optimal valve timing according to driving conditions. Using this system, lower fuel consumption, higher engine performance, and reduced exhaust emissions have been achieved.


f.

Change From 3UR-FE Engine:

i.

Hard-facing alloy is used for the intake valve face.


ii.

The use of hard-facing alloy on the exhaust valve face has been discontinued.

W131851C01
2.156,1.479 1.594,0.563 true 4.063,3.385 3.646,2.469 true 1.271,1.615 0.75,0.99 true 3.594,3.74 3.083,2.656 true 1.708,2.031 0.635,2.927 true 2.438,2.875 2.51,4.396 true 4.021,1.802 4.313,0.948 true 2.74,1.135 3.083,0.448 true 5.563,1.083 5.906,0.854 true 5.51,1.354 5.844,1.313 true 4.927,2.281 5.26,2.292 true 5.5,3.792 5.792,3.615 true 1.448,0.365 1.76,0.521 0.313,0.156 10 false *1 0.604,0.823 0.917,0.979 0.313,0.156 10 false *2 0.469,2.917 0.781,3.073 0.313,0.156 10 false *3 4.271,0.75 4.583,0.906 0.313,0.156 10 false *4 5.969,0.74 6.281,0.896 0.313,0.156 10 false *5 5.885,1.24 6.198,1.396 0.313,0.156 10 false *6 5.292,2.208 5.604,2.365 0.313,0.156 10 false *7 5.823,3.51 6.135,3.667 0.313,0.156 10 false *a 4.063,3.448 4.375,3.604 0.313,0.156 10 false *1 3.573,3.833 3.885,3.99 0.313,0.156 10 false *2 2.438,4.448 2.75,4.604 0.313,0.156 10 false *3 3.083,0.26 3.396,0.417 0.313,0.156 10 false *4
*1 Exhaust Camshaft *2 Secondary Timing Chain
*3 Primary Timing Chain *4 Intake Camshaft
*5 Valve Rocker Arm *6 Hydraulic Lash Adjuster
*7 Valve - -
*a Valve Face - -





Camshaft


a.

The camshafts are made of cast iron alloy.


b.

Oil passages are provided in the intake and exhaust camshafts in order to supply engine oil to the VVT-i system.


c.

VVT-i controllers are installed on the front of the intake and exhaust camshafts to vary the timing of the intake and exhaust valves.


d.

Together with the use of the roller rocker arms, the cam profile has been optimized. This results in increased valve lift when the valve begins to open and finishes closing, helping to achieve enhanced output performance.

W128383C02
0.448,3.104 2.438,4.208 1.99,1.104 0.448,4.344 2.438,5.448 1.99,1.104 3.729,3.646 3.729,3.333 true 6.521,1.042 6.333,1.688 6.333,1.688 6.115,1.042 true 4.813,3.188 4.813,2.802 true 3.031,3.188 3.031,2.802 true 0.729,1.385 0.729,1 true 2.031,1.156 2.031,0.771 true 3.281,1.313 3.281,0.927 true 4.448,2.042 4.448,1.656 true 1.208,2.375 1.594,2.031 true 3.313,2.51 1.958,2.698 1.958,2.698 1.802,2.177 true 2.146,3.656 1.542,3.438 true 2.219,4.75 1.531,4.948 true 1.948,0.594 2.177,0.802 0.229,0.208 10 false *1 3.667,3.688 3.896,3.896 0.229,0.208 10 false *2 0.646,0.833 0.875,1.042 0.229,0.208 10 false *2 1.833,2.74 2.063,2.948 0.229,0.208 10 false *2 1.094,2.385 1.323,2.594 0.229,0.208 10 false *3 2.969,3.219 3.198,3.427 0.229,0.208 10 false *3 0.5,3.115 0.729,3.323 0.229,0.208 10 false *c 0.469,4.365 0.698,4.573 0.229,0.208 10 false *d 5.885,0.594 6.115,0.802 0.229,0.208 10 false *a 6.271,1.74 6.552,1.969 0.281,0.229 10 false *b 3.219,0.76 3.448,0.969 0.229,0.208 10 false *6 4.396,1.49 4.625,1.698 0.229,0.208 10 false *5 4.75,3.208 4.979,3.417 0.229,0.208 10 false *4 2.208,3.594 2.438,3.802 0.229,0.208 10 false *e 2.26,4.656 2.49,4.865 0.229,0.208 10 false *e 6.604,0.583 6.833,0.792 0.229,0.208 10 false *a
*1 No. 2 Camshaft (Exhaust) *2 VVT-i Controller
*3 Timing Rotor *4 No. 4 Camshaft (Exhaust)
*5 No. 3 Camshaft (Intake) *6 No. 1 Camshaft (Intake)
*a Increased Valve Lift *b Optimized Profile of Camshaft Lobe
*c Cross Section of End of Intake Camshaft *d Cross Section of End of Exhaust Camshaft
*e Oil Passage - -




Timing Chain and Chain Tensioner


a.

Both the primary and secondary chains use roller chains with a pitch of 9.525 mm (0.375 in.).


b.

A timing chain tensioner is provided for each primary timing chain and secondary timing chain in each bank.


c.

Both the primary and secondary chain tensioners use oil pressure and a spring to maintain proper chain tension at all times. The tensioners suppress noise generated by the timing chains.


d.

The chain tensioner for the primary timing chain is a ratchet type with a non-return mechanism. Furthermore, an oil pocket creates oil pressure when the engine is started, and simultaneously applies oil pressure to the chain tensioner. This prevents the timing chain from flapping and reduces noise.

W128384C01
4.802,1.208 4.448,0.885 true 4.188,2.063 3.896,2.302 true 5.031,1.552 4.729,2.354 true 2.104,3.177 1.51,3.677 true 2.094,3.948 1.531,3.781 true 0.958,3.167 1.469,3.552 true 0.979,3.833 1.448,3.594 true 1.417,5.625 1.25,5.198 true 2.281,5.885 1.969,5.885 true 1.49,6.26 1.688,5.938 true 3.135,6.156 4.615,5.323 true 3.313,5.344 4.25,4.865 true 3.135,3.948 2.927,3.427 true 4,3.979 3.917,3.313 true 5.552,4.333 5.354,3.25 true 6.448,4.01 6.604,3.51 true 6.198,5.479 5.458,4.99 true 6.031,6.156 5.052,5.385 true 6.24,4.927 6.24,4.271 true 4.292,0.75 4.594,1.01 0.302,0.26 10 false *1 3.729,2.292 4.031,2.552 0.302,0.26 10 false *2 4.635,2.375 4.938,2.635 0.302,0.26 10 false *3 0.802,3.031 1.104,3.292 0.302,0.26 10 false *4 0.823,3.771 1.125,4.031 0.302,0.26 10 false *5 2.115,3.021 2.417,3.281 0.302,0.26 10 false *6 2.156,3.906 2.458,4.167 0.302,0.26 10 false *7 1.125,5.031 1.427,5.292 0.302,0.26 10 false *8 2.302,5.792 2.604,6.052 0.302,0.26 10 false *10 1.375,6.271 1.677,6.531 0.302,0.26 10 false *9 2.917,6.104 3.219,6.365 0.302,0.26 10 false *14 3.083,5.292 3.385,5.552 0.302,0.26 10 false *13 6,6.177 6.302,6.438 0.302,0.26 10 false *15 6.208,5.49 6.51,5.75 0.302,0.26 10 false *16 6.135,4.927 6.438,5.188 0.302,0.26 10 false *17 2.76,3.25 3.063,3.51 0.302,0.26 10 false *12 3.781,3.135 4.083,3.396 0.302,0.26 10 false *11 5.229,3.063 5.531,3.323 0.302,0.26 10 false *19 6.521,3.323 6.823,3.583 0.302,0.26 10 false *18 3.219,0.458 3.521,0.719 0.302,0.26 10 false *a 0.51,2.771 0.813,3.031 0.302,0.26 10 false *b 0.521,4.979 0.823,5.24 0.302,0.26 10 false *c
*1 Gasket *2 Chain Tensioner (Primary)
*3 Oil Pocket *4 Ball
*5 Ball Spring *6 Main Spring
*7 Plunger *8 Spring
*9 Cam Spring *10 Cam
*11 Chain Damper RH *12 Secondary Timing Chain RH
*13 Chain Slipper RH *14 Primary Timing Chain RH
*15 Primary Timing Chain LH *16 Chain Damper LH
*17 Secondary Chain LH *18 Secondary Chain Tensioner LH
*19 Chain Slipper LH - -
*a Chain Tensioner (Primary) LH Side *b Chain Tensioner (Secondary) RH Side
*c Chain Tensioner (Primary) RH Side - -




Timing Chain Cover


a.

The timing chain cover has an integrated construction consisting of the cooling system (water pump and water passage) and the lubrication system (oil pump and oil passage). Thus, the number of parts has been reduced, resulting in a weight reduction.


b.

An oil jet is provided in the oil pump cover to lubricate the timing chains.

W128385C01
2.135,1.635 2.646,0.74 true 1.219,1.479 0.927,0.885 true 0.844,2.74 0.844,2.302 true 2.396,3.083 2.313,2.677 true 4.719,1.063 4.563,0.531 true 4.021,2.396 3.802,1.917 true 4.281,2.438 4.521,1.979 true 4.802,2.938 4.667,2.521 true 5.417,3.042 5.323,2.302 true 0.792,0.719 1.073,0.969 0.281,0.25 10 false *1 0.792,2.781 1.073,3.031 0.281,0.25 10 false *2 2.365,3.125 2.646,3.375 0.281,0.25 10 false *3 2.615,0.583 2.896,0.833 0.281,0.25 10 false *4 4.469,0.365 4.75,0.615 0.281,0.25 10 false *3 3.688,1.76 3.969,2.01 0.281,0.25 10 false *5 4.479,1.813 4.76,2.063 0.281,0.25 10 false *6 4.771,2.99 5.052,3.24 0.281,0.25 10 false *7 5.385,3.073 5.667,3.323 0.281,0.25 10 false *8 2.302,3.385 2.583,3.635 0.281,0.25 10 false *a 5.521,3.385 5.802,3.635 0.281,0.25 10 false *b
*1 Water Pump Gasket *2 Water Pump
*3 Timing Chain Cover *4 Water Pump Swirl Chamber
*5 Oil Pump Cover *6 Oil Jet
*7 Oil Pump Rotor *8 Oil Pump Chamber
*a Front Side View *b Back Side View




Hydraulic Lash Adjuster


a.

The valve lash adjuster assemblies, which are located at the fulcrum (pivot point) of the roller rocker arms, each consist primarily of a plunger, a plunger spring, a check ball, and a check ball spring.


b.

The engine oil supplied from the cylinder head and the built-in spring actuates the valve lash adjuster. The oil pressure and the spring force that act on the plunger push the roller rocker arm against the cam. This adjusts the clearance between the valve stem and rocker arm, and thus prevents the generation of noise during the opening and closing of the valves. As a result, engine noise has been reduced.

W128386C01
2.021,0.917 2.021,0.427 true 1.583,1.875 1.104,1.333 true 1.865,2.49 1.021,1.958 true 1.813,2.656 0.948,2.417 true 1.729,2.823 1.042,3.135 true 4.073,1.458 3.615,0.708 true 4.323,0.813 4.24,0.417 true 4.552,1.438 5.083,0.656 true 4.156,1.719 5.938,1.25 true 1.958,0.25 2.219,0.469 0.26,0.219 10 false *1 0.969,1.177 1.229,1.396 0.26,0.219 10 false *2 0.875,1.813 1.125,2.021 0.25,0.208 10 false *3 0.792,2.323 1.042,2.531 0.25,0.208 10 false *4 0.885,3.104 1.135,3.313 0.25,0.208 10 false *5 3.479,0.521 3.729,0.729 0.25,0.208 10 false *6 4.177,0.26 4.427,0.469 0.25,0.208 10 false *7 5.052,0.5 5.302,0.708 0.25,0.208 10 false *8 5.958,1.167 6.208,1.375 0.25,0.208 10 false *2
*1 Plunger *2 Oil Passage
*3 Check Ball *4 Check Ball Spring
*5 Plunger Spring *6 Valve Lash Adjuster
*7 Cam *8 Roller Rocker Arm


HINT:

Valve clearance adjustment is not necessary because valve lash adjusters are used on this model.