Home › General › BODY ELECTRICAL › POWER SEAT SYSTEM
NM27L0U _V1 General _050243 BODY ELECTRICAL _0243561 POWER SEAT SYSTEM UN GENERAL/CONTROL/DETAILS F

BODY ELECTRICAL  POWER SEAT SYSTEM  GENERAL/CONTROL/DETAILS  REAR NO. 2 SEAT  


GENERAL


a.

The power seat system for the rear No. 2 seat is equipped with a reclining function and a tilt up/down function, which are controlled by the fold seat control ECU.


b.

The reclining function can adjust the reclining angle of the seatback.


c.

The tilt up/down function can tilt the rear No. 2 seat up or down with an electric motor.



SYSTEM DIAGRAM


Y196138E01
0.833,0.729 2.375,1.135 1.542,0.406 10 false Reclining Switch RH/LH 4.792,1.104 6.792,1.76 2,0.656 10 false No. 1 Reclining Motor Assembly RH/LH 4.833,1.927 6.406,2.208 1.573,0.281 10 false - Power seat Motor 4.823,2.24 6.552,2.656 1.729,0.417 10 false - Reclining Position Sensor 0.635,1.458 2.563,2.021 1.927,0.563 10 false Fold Seat Switch RH/LH (Deck side Trim Rear) 0.625,2.094 2.656,2.479 2.031,0.385 10 false Fold Seat Switch Indicator LIght 3.323,2.292 4.146,3.49 0.823,1.198 10 false Fold Seat Contorl ECU RH/LH 4.781,2.885 6.76,3.458 1.979,0.573 10 false No. 2 Reclining Motor Assembly RH/LH 5.177,3.635 6.365,4.229 1.188,0.594 10 false Power seat Motor 0.635,2.792 2.563,3.448 1.927,0.656 10 false Fold Seat Switch RH/LH (Deck side Trim Front) 0.615,3.438 2.604,3.771 1.99,0.333 10 false Fold Seat Switch Indicator LIght 0.604,4.156 2.729,4.646 2.125,0.49 10 false Rear Door Coutesy Switch RH/LH 0.615,4.979 2.542,5.271 1.927,0.292 10 false Back Door Lock Assembly 0.708,5.417 2.635,5.708 1.927,0.292 10 false - Back door Courtesy Switch 3.479,5.198 5.406,5.49 1.927,0.292 10 false Buzzer 0.688,6.167 2.615,6.458 1.927,0.292 10 false Park/Neutral Position Switch 0.688,6.635 2.615,6.927 1.927,0.292 10 false - P Position signal


LAYOUT OF MAIN COMPONENTS


Y196139C01
5.063,2.792 4.729,1.302 true 6.458,2.854 5.646,3.313 true 5.156,3.542 6.24,3.938 true 2.313,3.604 3.833,3.698 true 2.458,2.729 3.313,3.125 true 4.354,6.208 5.302,4.979 true 3.385,5.99 3.729,4.792 true 3.229,5.927 2.365,4.719 true 2.823,5.958 1.719,5.063 true 2.198,1.458 2.51,1.615 0.313,0.156 10 false *1 2.281,2.552 2.594,2.708 0.313,0.156 10 false *2 2.146,3.469 2.458,3.625 0.313,0.156 10 false *3 6.292,3.833 6.604,3.99 0.313,0.156 10 false *4 6.51,2.708 6.823,2.865 0.313,0.156 10 false *5 4.625,1.104 4.938,1.26 0.313,0.156 10 false *6 2.208,4.552 2.521,4.708 0.313,0.156 10 false *7 1.542,4.938 1.854,5.094 0.313,0.156 10 false *8 2.823,7.49 3.135,7.646 0.313,0.156 10 false *9 2.813,8.156 3.281,8.313 0.469,0.156 10 false *10 5.26,4.792 5.729,4.948 0.469,0.156 10 false *11 3.667,4.604 4.135,4.76 0.469,0.156 10 false *12
*1 Fold Seat Switch RH/LH *2 Rear Door Courtesy Switch LH
*3 Fold Seat Control ECU LH *4 Back Door Lock Assembly
·

Back Door Courtesy Switch


*5 Fold Seat Control ECU RH *6 Rear Door Courtesy Switch RH
*7 Rear Door Courtesy Switch RH *8 Rear Door Courtesy Switch RH
*9 Reclining Switch RH/LH *10 Fold Seat Switch RH/LH
*11 No. 1 Reclining Motor Assembly LH *12 No. 1 Reclining Motor Assembly LH



RECLINING FUNCTION


a.

General

i.

The reclining function has an adjustable range of 28 degrees.

Y196140E01
1.917,0.24 2.375,0.438 0.458,0.198 10 false (4) 2.979,0.542 3.438,0.74 0.458,0.198 10 false (2) 3.49,0.99 3.948,1.188 0.458,0.198 10 false (2) 3.49,1.573 3.948,1.771 0.458,0.198 10 false (1) 2.406,0.979 2.865,1.177 0.458,0.198 10 false (1) 1.51,0.677 1.969,0.875 0.458,0.198 10 false (3) 6.26,1.594 6.719,1.792 0.458,0.198 10 false (3) 6.24,0.99 6.698,1.188 0.458,0.198 10 false (4) 5.24,1.865 5.906,2.521 0.667,0.656 10 false Reclining Switch RH 4.094,1.854 4.76,2.51 0.667,0.656 10 false Reclining Switch LH




TILT UP/DOWN FUNCTION


a.

General

i.

The tilt up/down function can tilt the rear No. 2 seat up or down by pressing and holding the fold seat switch.


ii.

The tilt up/down function is controlled by the fold seat control ECU.


iii.

The tilt up/down function can be used when the following conditions are met.

1.

The ignition switch is OFF

2.

The ignition switch is ON and the shift lever is in the P position

3.

The door, which corresponds to the folding seat switch that is being operated, is open

·

Fold Seat Switch RH (Deck Side Trim Front) → Rear Door RH

·

Fold Seat Switch LH (Deck Side Trim Front) → Rear Door LH

·

Fold Seat Switch RH/LH (Deck Side Trim Rear) → Back Door




iv.

When the tilt up/down function is operated, the seat can come in contact with the rear No. 1 seat. Therefore, operate this function after down the headrests.

Y196141C01
2.01,2.573 2.323,2.729 0.313,0.156 10 false *a 4.99,2.573 5.302,2.729 0.313,0.156 10 false *b 2.188,5.063 2.49,5.25 0.302,0.188 10 false *c 2.74,3.844 3.052,4 0.313,0.156 10 false *d 4.052,3.219 4.365,3.375 0.313,0.156 10 false *e 5.167,3.76 5.479,3.99 0.313,0.229 10 false *f 3.385,5.333 3.781,5.615 0.396,0.281 10 false *g
*a Tilt Up Function *b Tilt Down Function
*c Folding Position *d Non-seating Range
*e Seating Range *f Rearmost Position
*g Operation Range - -




b.

Operation

i.

Tilt Down Operation

The tilt down operation is carried out as follows. The described operation is for the rear No. 2 seat LH. The operation for the rear No. 2 seat RH is the same as the LH.

1.

Under either of the following conditions, the user presses and holds the tilt down side of the fold seat switch LH when the rear door LH or the back door is open:

1.

The ignition switch is OFF

2.

The ignition switch is ON and the shift lever is in the P position


2.

The buzzer sounds twice, the No. 1 and No. 2 reclining motors actuate, and the seat operates until it is in the folding position. However, if the rear No. 2 seat is in the seating range, the operation can be ended at any position. At this time, the buzzer sounds twice.

3.

If the reclining position sensor determines that the seat is in the folding position, the buzzer sounds twice and the tilt down operation ends.

4.

If the fold seat switch LH is turned OFF during a tilt down operation and the rear No. 2 seat is in a non-seating range, the operation stops, the fold seat switch indicator light illuminates, and the buzzer sounds for approximately 10 seconds.

Y196142C01
1.573,1.052 2.01,1.49 true 1.406,0.896 1.719,1.052 0.313,0.156 10 false *1 1.917,2.354 2.229,2.51 0.313,0.156 10 false *2 1.135,2 1.448,2.156 0.313,0.156 10 false *a
*1 Fold Seat Switch Indicator Light *2 Fold Seat Switch LH
*a Tilt Down Side - -





ii.

Tilt Up Operation

The tilt up operation is carried out as follows. The described operation is for the rear No. 2 seat LH. The operation for the rear No. 2 seat RH is the same as the LH.

1.

Under either of the following conditions, the user presses and holds the tilt up side of the fold seat switch LH when the rear door LH or the back door is open:

1.

The ignition switch is OFF

2.

The ignition switch is ON and the shift lever is in the P position


2.

The buzzer sounds twice, the No. 1 and No. 2 reclining motors actuate, and the seat operates until it is in the rearmost position. However, if the rear No. 2 seat is in the seating range, the operation can be ended at any position. At this time, the buzzer sounds twice.

3.

If the reclining position sensor determines that the seat is in the rearmost position, the buzzer sounds twice and the tilt up operation ends.

4.

If the fold seat switch LH is turned OFF during a tilt up operation and the rear No. 2 seat is in a non-seating range, the operation stops, the fold seat switch indicator light illuminates, and the buzzer sounds for approximately 10 seconds.

Y196143C01
1.344,0.906 1.771,1.375 true 1.177,0.781 1.49,0.938 0.313,0.156 10 false *1 1.688,2.219 2,2.375 0.313,0.156 10 false *2 0.896,1.51 1.208,1.667 0.313,0.156 10 false *a
*1 Fold Seat Switch Indicator Light *2 Fold Seat Switch LH
*a Tilt Up Side - -






c.

Jam Protection Function

i.

General

·

The jam protection function is controlled by the fold seat control ECU.

·

In the tilt down operation, the seatback operates after jam detection as follows: When the jam protection function operates, the seat back reverses approximately 50 degrees.

·

In the tilt up operation, the seatback operates after jam detection as follows: When the jam protection function operates, the seat back reverses approximately 10 degrees.



ii.

Jammed Seat Detection Mechanism

·

The jammed seat detection mechanism uses the Hall IC on the No. 1 reclining motor assembly.

·

The following two factors are used to determine that jamming has occurred.

1.

The Hall IC converts the changes in the magnetic flux that occur through the rotation of the worm gear into block wave signals and outputs them to the fold seat control ECU.

2.

The fold seat control ECU calculates the speed threshold value of the No. 1 reclining motor in accordance with the seat reclining position at the time the No. 1 reclining motor is started. The fold seat control ECU determines that jamming has occurred if the threshold value is exceeded, and reverses the seatback.

Determination by Hall IC
Y196144E01
4.281,1.948 5.698,2.792 1.417,0.844 10 false No 1 Reclining Motor 1 Revolution (Jammed) 0.938,1.948 2.354,2.792 1.417,0.844 10 false No 1 Reclining Motor 1 Revolution (Normal) 0.104,0.75 0.99,1.188 0.885,0.438 10 false Hall IC Output Signal





d.

Warning

i.

If the fold seat control ECU detects a malfunction in the tilt up/down function, the buzzer sounds for 10 seconds, the fold seat switch indicator light illuminates or flashes. Refer to the table below for details.

Malfunction Buzzer Fold Seat Switch Indicator Light
Illuminate Flash
While the tilt up/down function is operating and the rear No. 2 seat is in a non-seating range, the fold seat switch is turned OFF. ○ ○ -
While the tilt up/down function is operating and the rear No. 2 seat is in a non-seating range, the ignition switch is ON and the shift lever is moved to a position other than P. ○ ○ -
While the tilt up/down function is operating and the rear No. 2 seat is in a non-seating range, the reclining motor has stopped due to an overcurrent or pulse malfunction. ○ - ○
While the tilt up/down function is operating and the rear No. 2 seat is in a non-seating range, the courtesy light switch that corresponds to the respective fold seat switch has turned ON. ○ - -
While the tilt up/down function is operating and the rear No. 2 seat is in a non-seating range, the seat has not reached the folding position or rearmost position even after 30 seconds have elapsed after the start of the operation. ○ - ○