Home › General › BODY ELECTRICAL › POWER WINDOW SYSTEM
NM27L0U _V1 General _050243 BODY ELECTRICAL _0244355 POWER WINDOW SYSTEM UN GENERAL/CONTROL/DETAILS F

BODY ELECTRICAL  POWER WINDOW SYSTEM  GENERAL/CONTROL/DETAILS  JAM PROTECTION FUNCTION  


GENERAL


a.

The jam protection function is controlled by the power window ECU or the back door ECU.


b.

The jam protection function automatically stops the power window and moves it downward if a foreign object gets jammed in the door window during one-touch auto-up operation or manual-up operation.


c.

The mechanism uses a Hall IC to detect the door glass position and direction of movement.



FRONT DOOR


a.

General

i.

The power window ECU is built into the driver and front passenger power window motor assemblies.


ii.

The reverse-direction conditions and amount of down movement after jam detection are as follows: The jam protection function operates and lowers the window approximately 50 mm (1.9 in.). After this, if the amount (space) that the door glass is open has not reached approximately 200 mm (7.87 in.), the jam protection function will continue to lower the window until the space is approximately 200 mm (7.87 in.). If the door glass reaches the fully open position before the initial 50 mm (1.9 in.) lowering of the door glass is reached, the jam protection function will stop at that time.



b.

Jammed Window Detection Mechanism

i.

The jammed window detection mechanism consists of a magnet that is provided on the worm gear of the driver and front passenger power window motor assemblies, the power window ECU, and the Hall IC that is provided on the power window ECU.


ii.

The following two factors are used to determine that jamming has occurred.

1.

The Hall IC converts the changes in the magnetic flux that occur through the rotation of the worm gear into block wave signals and outputs them to the power window ECU.

2.

The power window ECU calculates the speed threshold value of the power window motor in accordance with the window glass position, rough road condition, and various operating conditions at the time the power window motor is started. The power window ECU determines that jamming has occurred if the threshold value is exceeded, and retracts the window glass.

Determination by Hall IC
Y196099E01
0.104,1.167 0.99,1.875 0.885,0.708 10 false Hall IC Output Signal 0.958,1.896 2.448,2.677 1.49,0.781 10 false Power Window Motor 1 Revolution (Normal) 4.146,1.896 5.656,2.74 1.51,0.844 10 false Power Window Motor 1 Revolution (Jammed)

Determination by Power Window Motor Speed
Y196100E01
3.948,0.521 4.969,0.302 true 5.01,0.177 6.75,0.594 1.74,0.417 10 false Speed Threshold Value 1.938,0.521 2.177,0.833 0.24,0.313 10 false 0 1.813,1.146 2.135,1.458 0.323,0.313 10 false ON 1.792,1.49 2.229,1.813 0.438,0.323 10 false OFF 1.771,1.948 2.063,2.271 0.292,0.323 10 false ON 1.74,2.229 2.156,2.563 0.417,0.333 10 false OFF 0.281,0.156 1.427,1.229 1.146,1.073 10 false Deterrmination by Power window Motor Speed 0.271,1.167 1.24,1.844 0.969,0.677 10 false Power Window Motor Up 0.229,1.906 1.271,2.594 1.042,0.688 10 false Power Window Motor down





BACK DOOR


a.

General

i.

The jam protection function consists of a back door power window motor assembly and back door ECU. The back door ECU receives signals from the back door power window motor assembly in order to determine whether the back door window is jammed.



b.

Jammed Window Detection Mechanism

i.

The Hall IC converts the changes in the magnetic flux that occur through the rotation of the worm gear into pulse signals and outputs them to the back door ECU.


ii.

To control the jam protection function, the back door ECU determines the amount of movement and the jamming of the power window from the pulse signals from the Hall IC1, and the moving direction of the power window from the phase difference between the pulses from the Hall IC1 and Hall IC2.

Judgment of Amount of Movement and Jamming
Y196101E01
1.177,1.344 1.938,1.625 0.76,0.281 10 false Normal 0.219,0.229 0.771,1.125 0.552,0.896 10 false Hall IC1 signal 4.469,1.344 5.333,1.677 0.865,0.333 10 false Jammed 5.51,0.833 6.854,1.625 1.344,0.792 10 false Amount of Movement of Motor 1 Revolution 1.74,0.854 3.083,1.646 1.344,0.792 10 false Amount of Movement of Motor 1 Revolution

Judgment of Moving Direction
Y196102E01
1.906,1.875 2.469,2.198 0.563,0.323 10 false OPEN 4.802,1.885 5.615,2.25 0.813,0.365 10 false CLOSE 0.354,0.427 1.417,0.854 1.063,0.427 10 false Hall IC1 Signal 0.385,1.417 1.458,1.906 1.073,0.49 10 false Hall IC2 Signal