Home › General › BODY ELECTRICAL › POWER BACK DOOR SYSTEM
NM27L0U _V1 General _050243 BODY ELECTRICAL _0244356 POWER BACK DOOR SYSTEM UN GENERAL/CONTROL/DETAILS F

BODY ELECTRICAL  POWER BACK DOOR SYSTEM  GENERAL/CONTROL/DETAILS  SYSTEM OPERATION  


GENERAL


a.

This system performs the functions listed below.

Function Outline
Opener Function Upon receiving an ON signal from the power back door opener/closer switch or the power back door button on the transmitter with the back door unlocked, the power back door ECU actuates the opener and closer motor and the power back door motor in order to release the latch of the back door lock and open the back door.
One-motion Opener Function Upon receiving an ON signal from the power back door button on the transmitter with the back door locked, the power back door ECU actuates the opener and closer motor and the power back door motor in order to release the latch of the back door lock and open the back door.
Closer Function If any of the following conditions is met, the power back door ECU actuates the power back door motor and the opener and closer motor in order to close the back door and engage the latch of the back door lock.
·

With the back door open, an ON signal is output from the power back door opener/closer switch.

·

With the back door open, an ON signal is output from the power back door closer switch.

·

With the back door open, the power back door button on the transmitter is pressed.


Jam Protection Function Upon receiving the signals from a touch sensor and the Hall ICs of the power back door motor, the power back door ECU detects that an object is jammed in the back door, and reverses the movement of the power back door motor.The power back door buzzer sounds for 0.1 seconds when a jammed object is detected.
Reverse Control Function During a power back door operation, if the power back door ECU detects an ON signal from the power back door opener/closer switch or the power back door button on the transmitter, the power back door ECU sounds the power back door buzzer for approximately 0.1 seconds and reverses the power back door motor in order to reverse the back door to a predetermined position.
Back Door Open/Close Speed Control Function In accordance with the signals received from the Hall ICs, the power back door ECU effects the following controls:
·

Reduces the closing speed from approximately 330 mm (13.0 in.) before the back door is fully closed, in order to reduce the jamming load.

·

Reduces the opening speed from approximately 250 mm (9.8 in.) before the back door is fully open, in order to reduce the shock that occurs when it is fully open.


Diagnosis If the power back door ECU detects a malfunction in the power back door system, the power back door ECU diagnoses the failed section and stores the DTC (Diagnostic Trouble Code) in the main body ECU via the CAN. For details, see the 2008 Sequoia Repair Manual (Pub. No. RM08L0U).
Fail-safe If the power back door ECU detects any of the malfunctions listed below during power back door operation, the power back door ECU stops the power back door motor and sounds the power back door buzzer simultaneously, then turns OFF the magnetic clutch and stops the system.
·

Open circuit in the touch sensor

·

The power back door motor is operated continuously for 30 seconds or more.

·

Abnormal back door position signal (Hall IC signal)

·

Abnormality with position switches on back door lock assembly.


During a power back door operation, if the shift lever is shifted to a position other than P, the power back door ECU performs the aforementioned fail-safe operation.



OPENER FUNCTION


a.

The power back door opener/closer switch or the power back door button on the transmitter is turned ON for 0.8 seconds or more with the back door unlocked.


b.

The power back door buzzer and wireless door lock buzzer will sound for 0.8 seconds. The hazard lights will flash twice simultaneously with the start of the operation.


c.

The opener and closer motor operates to unlock the latch.


d.

Through the state of the courtesy switch, the power back door ECU detects that the latch has been released, and actuates the power back door motor to start opening the back door.


e.

Through the state of the half latch switch, the power back door ECU detects that the back door is open, and reverses the opener and closer motor to its initial position.


f.

Through the state of the position switch, the power back door ECU detects that the motor has reverted to its initial position. Then, it stops the opener and closer motor.


g.

Through the Hall ICs of the power back door motor, the power back door ECU detects the back door position, and stops the power back door motor just before the back door is in its full open position, and turns OFF the magnetic clutch.

Y196108E01
0.948,0.833 1.927,1.198 0.979,0.365 10 false Transmitter 0.531,1.771 2.104,2.156 1.573,0.385 10 false Door Control Receiver 0.542,3.208 2.24,3.615 1.698,0.406 10 false Power Back Door Buzzer 3.083,0.896 4.073,2.219 0.99,1.323 10 false Main Body ECU (Driver Side Junction Block) 4.792,0.594 6.781,1.25 1.99,0.656 10 false Power Back Door Opener/Closer Switch 4.771,1.521 6.552,1.896 1.781,0.375 10 false Turn Signal Flasher Ralay 4.781,2.156 6.563,2.521 1.781,0.365 10 false Wireless Door Lock Buzzer 3.688,2.698 4.792,3.052 1.104,0.354 10 false CAN (MS Bus) 4.563,3.448 6.688,3.802 2.125,0.354 10 false Power Back Door Drive Unit 3.198,4.594 4,5.635 0.802,1.042 10 false Power Back Door ECU 0.396,3.917 2.313,4.271 1.917,0.354 10 false Back Door Lock Assembly 0.271,4.917 1.865,5.323 1.594,0.406 10 false Opener and Closer Motor 0.552,5.448 1.729,5.792 1.177,0.344 10 false Half Latch Switch 0.583,6.063 1.677,6.469 1.094,0.406 10 false Position Switch 0.563,6.583 1.708,6.896 1.146,0.313 10 false Coutesy Switch 4.906,5.938 5.427,6.302 0.521,0.365 10 false Hall IC 5.323,5.219 6.385,5.625 1.063,0.406 10 false Magnetic Clutch 5.292,4.344 6.24,5.052 0.948,0.708 10 false Power Back Door Motor 4.292,4.271 4.865,4.635 0.573,0.365 10 false (d), (g) 4.292,5.146 4.865,5.51 0.573,0.365 10 false (d), (g) 5.771,5.875 6.083,6.208 0.313,0.333 10 false (g) 5.854,6.51 6.167,6.844 0.313,0.333 10 false (g) 1.948,4.813 2.729,5.125 0.781,0.313 10 false (c), (e), (f) 2.51,2 3.042,2.354 0.531,0.354 10 false (a), (b) 2.646,5.385 2.969,5.729 0.323,0.344 10 false (e) 2.667,5.969 2.99,6.313 0.323,0.344 10 false (f) 2.656,6.521 2.979,6.865 0.323,0.344 10 false (d) 4.917,6.5 5.438,6.865 0.521,0.365 10 false Hall IC 2.292,3.49 2.615,3.833 0.323,0.344 10 false (b) 4.51,2.396 4.771,2.708 0.26,0.313 10 false (b) 4.5,1.771 4.792,2.042 0.292,0.271 10 false (b) 1.656,1.281 2.292,1.615 0.635,0.333 10 false (a), (b) 4.177,1 4.469,1.271 0.292,0.271 10 false (a)



ONE-MOTION OPENER FUNCTION


a.

The power back door button on the transmitter is turned ON for 0.8 seconds or more with the back door locked.


b.

The power back door buzzer and wireless door lock buzzer will sound for 0.8 seconds. The hazard lights will flash twice simultaneously with the start of the operation.


c.

The opener and closer motor operates to unlock the latch.


d.

Through the state of the courtesy switch, the power back door ECU detects that the latch has been released, and actuates the power back door motor to start opening the back door.


e.

Through the state of the half latch switch, the power back door ECU detects that the back door is open, and reverses the opener and closer motor to its initial position.


f.

Through the state of the position switch, the power back door ECU detects that the motor has reverted to its initial position. Then, it stops the opener and closer motor.


g.

Through the Hall ICs of the power back door motor, the power back door ECU ECU detects the back door position, and stops the power back door motor just before the back door is in its full open position, and turns OFF the magnetic clutch.

Y196109E01
4.833,0.781 6.479,1.427 1.646,0.646 10 false Turn Signal Flasher Ralay 4.802,1.656 6.583,2.281 1.781,0.625 10 false Wireless Door Lock Buzzer 3.073,0.917 4.094,2.479 1.021,1.563 10 false Main Body ECU (Instrument Panel Junction Blok) 4.51,1.01 5.031,1.438 0.521,0.427 10 false (b) 4.521,1.927 5.042,2.354 0.521,0.427 10 false (b) 0.99,0.823 1.865,1.156 0.875,0.333 10 false Transmitter 0.688,1.771 2.219,2.083 1.531,0.313 10 false Door Control Receiver 1.615,1.281 2.135,1.708 0.521,0.427 10 false (a), (b) 2.594,2.031 3.115,2.458 0.521,0.427 10 false (a), (b) 3.708,2.646 4.781,2.979 1.073,0.333 10 false CAN (MS Bus) 4.344,3.49 6.167,3.802 1.823,0.313 10 false Power Back Door Drive Unit 2.323,3.51 2.844,3.938 0.521,0.427 10 false (b) 0.573,3.26 2.208,3.646 1.635,0.385 10 false Power Back Door Buzzer 0.302,3.854 2.042,4.271 1.74,0.417 10 false Back Door Lock Assembly 5.281,4.375 6.063,5.292 0.781,0.917 10 false Power Back Door Motor 4.375,4.271 5.156,5.188 0.781,0.917 10 false (d), (g) 4.396,5.156 5.177,6.073 0.781,0.917 10 false (d), (g) 5.344,5.094 5.99,6.031 0.646,0.938 10 false Magnetic Clutch 4.917,5.927 5.396,6.167 0.479,0.24 10 false Hall IC 4.917,6.479 5.396,6.719 0.479,0.24 10 false Hall IC 5.635,5.917 6.115,6.156 0.479,0.24 10 false (g) 5.875,6.531 6.354,6.771 0.479,0.24 10 false (g) 3.198,4.802 3.979,5.719 0.781,0.917 10 false Power Back Door ECU 0.521,4.896 1.76,5.365 1.24,0.469 10 false Opener and Closer Motor 1.969,4.823 2.802,5.146 0.833,0.323 10 false (c), (e), (f) 2.688,5.406 3.521,5.729 0.833,0.323 10 false (e) 2.708,5.99 3.542,6.313 0.833,0.323 10 false (f) 2.708,6.563 3.542,6.885 0.833,0.323 10 false (d) 0.75,5.49 2.208,5.885 1.458,0.396 10 false Half Latch Switch 0.76,6.031 2.219,6.427 1.458,0.396 10 false Position Switch 0.74,6.583 2.198,6.979 1.458,0.396 10 false Coutesy Switch



CLOSER FUNCTION


a.

The power back door opener/closer switch, the power back door closer switch, or the power back door button on the transmitter is turned ON for 0.8 seconds or more with the back door open, or the back door is manually closed to a predetermined position.


b.

The power back door buzzer and wireless door lock buzzer will sound for 0.8 seconds. The hazard lights will flash twice simultaneously with the start of the operation.


c.

The power back door ECU actuates the power back door motor to start closing the back door.


d.

Upon detecting that the latch is disengaged through the state of the half latch switch, the power back door ECU actuates the opener and closer motor to engage the latch.


e.

Upon detecting that the back door has closed through the state of the courtesy switch, the power back door ECU stops the magnetic clutch and the power back door motor.


f.

Upon detecting that the latch has been engaged through the state of the half latch switch (ON → OFF), the power back door ECU operates the opener and closer motor forward in order to fully close the back door.


g.

If the power back door ECU detects that the half latch switch has been turned ON again after the back door has fully closed, it stops the opener and closer motor. Then, it operates the opener and closer motor in reverse until the position switch turns ON.

Y196108E02
0.906,0.823 1.906,1.198 1,0.375 10 false Transmitter 1.719,1.323 2.396,1.656 0.677,0.333 10 false (a), (b) 0.469,1.771 2.135,2.167 1.667,0.396 10 false Door Control Receiver 3.083,1.094 4.073,2.396 0.99,1.302 10 false Main Body ECU (Driver Side Junction Block) 4.792,0.615 6.792,1.26 2,0.646 10 false Power Back Door Opener/Closer Switch 4.781,1.542 6.531,1.896 1.75,0.354 10 false Turn Signal Flasher Ralay 4.76,2.156 6.552,2.542 1.792,0.385 10 false Wireless Door Lock Buzzer 3.698,2.75 4.74,3.073 1.042,0.323 10 false CAN (MS Bus) 4.385,3.448 6.333,3.792 1.948,0.344 10 false Power Back Door Drive Unit 0.479,3.188 2.188,3.625 1.708,0.438 10 false Power Back Door Buzzer 0.417,3.938 2.25,4.302 1.833,0.365 10 false Back Door Lock Assembly 5.24,4.26 6.354,5.01 1.115,0.75 10 false Power Back Door Motor 5.313,5.167 6.417,5.583 1.104,0.417 10 false Magnetic Clutch 4.896,5.938 5.385,6.229 0.49,0.292 10 false Hall IC 2.26,2.135 2.938,2.469 0.677,0.333 10 false (a), (b) 2.313,3.49 2.625,3.75 0.313,0.26 10 false (b) 1.948,4.813 2.802,5.146 0.854,0.333 10 false (d), (f), (g) 4.281,4.271 4.844,4.542 0.563,0.271 10 false (c), (e) 0.25,4.906 1.865,5.375 1.615,0.469 10 false Opener and Closer Motor 0.531,5.458 1.708,5.813 1.177,0.354 10 false Half Latch Switch 0.531,6.042 1.677,6.417 1.146,0.375 10 false Position Switch 0.531,6.542 1.646,6.885 1.115,0.344 10 false Coutesy Switch 4.458,2.385 4.771,2.719 0.313,0.333 10 false (b) 4.469,1.75 4.781,2.083 0.313,0.333 10 false (b) 4.198,0.979 4.49,1.24 0.292,0.26 10 false (a) 2.135,5.385 2.885,5.813 0.75,0.427 10 false (d), (f), (g) 2.656,5.969 3,6.333 0.344,0.365 10 false (g) 2.646,6.521 2.927,6.844 0.281,0.323 10 false (e) 4.292,5.135 4.854,5.406 0.563,0.271 10 false (c), (e) 4.917,6.51 5.406,6.802 0.49,0.292 10 false Hall IC 3.208,4.854 3.99,5.823 0.781,0.969 10 false Power Back Door ECU



JAM PROTECTION FUNCTION


a.

The power back door ECU determines a jamming of the back door based on the power back door operation condition and operates the back door in the reverse direction.

Power Back Door Operation Condition Detection Item Action
Close The back door is reversed when one of the following conditions is met:
·

Jammed condition is detected through Hall IC signal.

·

Lock condition is detected through Hall IC signal.


Depending on detection timing, the close operation is cancelled and the back door warning buzzer sounds. → Back door is reversed (open operation).
During Lock The back door is reversed when one of the following conditions is met:
·

Lock condition is detected through Hall IC signal.

·

Jammed condition is detected through touch sensor.


Depending on detection timing, the close operation is cancelled and the back door warning buzzer sounds and the lock is released. → Back door is reversed (open operation).
Open The back door is reversed when one of the following conditions is met:
·

Jammed condition is detected through Hall IC signal.

·

Lock condition is detected through Hall IC signal.


Depending on detection timing, the open operation is cancelled and the back door warning buzzer sounds. → Back door is reversed (close operation).