Home › General › CHASSIS › BRAKE
NM27L0U _V1 General _050239 CHASSIS _0244924 BRAKE UN GENERAL/CONTROL/DETAILS F

CHASSIS  BRAKE  GENERAL/CONTROL/DETAILS  BRAKE CONTROL SYSTEM  


General


a.

The brake control system has the following functions:

Function Outline Model
2WD 4WD
Anti-lock Brake System (ABS) The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface. ○ ○
Electronic Brake force Distribution (EBD) The EBD utilizes the ABS, realizing the proper brake force distribution between front and rear wheels in accordance with the driving conditions. In addition, during cornering braking, it also controls the brake forces of right and left wheels, helping maintain the vehicle behavior. ○ ○
Brake Assist
·

The primary purpose of brake assist is to provide a supplementary braking force to assist a driver who cannot generate a large brake force during emergency braking, thus helping improve the vehicle's braking performance.

·

If the brake booster malfunctions and the skid control ECU judges that the brake pedal force applied by the driver is not sufficient to ensure adequate braking force, brake assist is used to enhance the braking force.


○ ○
Traction Control (TRAC) TRAC helps prevent the drive wheels from slipping if the driver presses the accelerator pedal excessively when starting off or accelerating on a slippery surface. ○ ○*
Active Traction Control (A-TRAC) When the vehicle drive mode is H4 or L4, the A-TRAC operates. A-TRAC controls the brake hydraulic pressure that is applied to the slipping wheel, and distributes the drive force that would have been lost through the slippage to the remaining wheels in order to achieve an LSD effect. - ○
Auto Limited Slip Differential (LSD) Briefly pressing the VSC OFF switch in normal mode enters TRAC OFF mode, allowing the Auto LSD to operate. The Auto LSD achieves a function equivalent to that of an LSD system through the use of the TRAC. The Auto LSD applies brake hydraulic pressure to a slipping wheel to reduce the difference in rotation speed between the left and right drive wheels. This causes driving torque to be transmitted to the wheel opposite the slipping wheel. ○ ○*
Vehicle Stability Control (VSC) VSC helps prevent the vehicle from slipping sideways as a result of strong front wheel skid or strong rear wheel skid during unstable situation [VSC operates when the vehicle speed is 15 km/h (9.3 mph) or more]. ○ ○
Trailer Sway Control If the tongue load is not properly adjusted while towing a trailer, trailer sway may be caused due to crosswinds, bumpy roads, steering operation, etc. Trailer sway control detects sway and regulates the brake of each wheel and the motive force output in order to suppress trailer sway. ○ ○

HINT:

*: For 4WD models, these functions operate while in 2WD mode.




Drive Modes


a.

The brake control functions vary by the drive mode as shown in the following table:

2WD Models
Brake Control VSC OFF Switch
Normal Mode TRAC OFF Mode Auto LSD Mode VSC OFF Mode
ABS ○ ○ ○ ○
EBD ○ ○ ○ ○
Brake Assist ○ ○ ○ ○
TRAC ○ X X X
Auto LSD X ○ ○ X
VSC ○ ○ X X
Trailer Sway Control ○ ○ X X

HINT:

○ : Controlled

X: Not controlled


4WD Models (Drive Mode: 2WD)
Brake Control VSC OFF Switch
Normal Mode TRAC OFF Mode Auto LSD Mode VSC OFF Mode
ABS ○ ○ ○ ○
EBD ○ ○ ○ ○
Brake Assist ○ ○ ○ ○
TRAC ○ X X X
A-TRAC X X X X
Auto LSD X ○ ○ X
VSC ○ ○ X X
Trailer Sway Control ○ ○ X X

HINT:

○ : Controlled

X: Not controlled


4WD Models [Drive Mode: 4WD (H4F)]
Brake Control VSC OFF Switch
Normal Mode TRAC OFF Mode VSC OFF Mode
ABS ○ ○ ○
EBD ○ ○ ○
Brake Assist ○ ○ ○
TRAC X X X
A-TRAC ○ X X
Auto LSD X X X
VSC ○ ○ X
Trailer Sway Control ○ ○ X

HINT:

○ : Controlled

X: Not controlled


4WD Models [Drive Mode: 4WD (L4F)]
Brake Control VSC OFF Switch
Normal Mode VSC OFF Mode
ABS ○ ○
EBD ○ ○
Brake Assist ○ ○
TRAC X X
A-TRAC ○ X
Auto LSD X X
VSC ○ X
Trailer Sway Control ○ X

HINT:

○ : Controlled

X: Not controlled


4WD Models [Drive Mode: 4WD (H4L or L4L)]
Brake Control VSC OFF Switch
Normal Mode VSC OFF Mode
ABS ○ ○
EBD ○ ○
Brake Assist ○ ○
TRAC X X
A-TRAC ○ X
Auto LSD X X
VSC X X
Trailer Sway Control X X

HINT:

○ : Controlled

X: Not controlled




System Diagram


X131052E01
1.083,6.698 1.531,7.052 0.448,0.354 10 false ECM 0.615,7.25 2.031,7.625 1.417,0.375 10 false 4WD Control ECU*1 0.333,7.823 2.198,8.198 1.865,0.375 10 false Suspension Control ECU*2 0.177,8.292 1.375,8.646 1.198,0.354 10 false *1: 4WD models 1.677,8.302 4.844,8.698 3.167,0.396 10 false *2: Models with rear air suspension system 2.583,6.365 3.552,6.729 0.969,0.365 10 false CAN (V1 Bus) 0.292,6.229 1.042,6.583 0.75,0.354 10 false Stop Light 0.74,5.75 2.104,6.094 1.365,0.344 10 false BRK NO. 2 Relay 0.729,5.188 2.177,5.573 1.448,0.385 10 false BRK NO. 1 Relay 0.646,4.625 1.969,4.99 1.323,0.365 10 false Stop Light Switch 5.51,4.469 6.615,4.802 1.104,0.333 10 false Brake Booster 5.406,4.948 6.698,5.26 1.292,0.313 10 false Booster Solenoid 5.542,5.427 6.625,5.729 1.083,0.302 10 false Micro Switch 5.198,5.896 6.823,6.229 1.625,0.333 10 false Booster Stroke Sensor 5.74,6.708 6.344,7.052 0.604,0.344 10 false DLC3 5.188,7.26 6.771,7.615 1.583,0.354 10 false Steering Angle Sensor 4.99,7.802 6.969,8.188 1.979,0.385 10 false Combination Meter Assembly 0.125,4.073 2.354,4.49 2.229,0.417 10 false Yaw Rate and Deceleration Sensor 0.125,3.521 2.344,3.948 2.219,0.427 10 false Center Diff. Lock Position Switch*1 0.542,2.979 2,3.385 1.458,0.406 10 false Parking Brake Switch 0.635,2.406 2.021,2.74 1.385,0.333 10 false VSC OFF Switch 0.365,1.854 2,2.219 1.635,0.365 10 false Rear Speed Sensor LH 0.375,1.302 2.042,1.698 1.667,0.396 10 false Rear Speed Sensor RH 0.365,0.75 2.021,1.156 1.656,0.406 10 false Front Speed Sensor LH 0.385,0.188 2.198,0.542 1.813,0.354 10 false Front Speed Sensor RH 3.292,0.49 3.865,1.26 0.573,0.771 10 false Solenoid Relay 3.208,2.552 4.042,2.938 0.833,0.385 10 false Motor Relay 3.031,1.698 4.177,2.167 1.146,0.469 10 false Skid Control ECU 4.844,3.99 6.063,4.344 1.219,0.354 10 false Brake Actuator 5.438,3.031 6.531,3.792 1.094,0.76 10 false Master Cylinder Pressure Sensor 5.604,2.552 6.5,2.906 0.896,0.354 10 false Pump Motor 5.365,2.083 6.677,2.427 1.313,0.344 10 false Solenoid Valves (8) 5.292,1.208 6.688,1.958 1.396,0.75 10 false Reservoir Cut Solenoid Valves (2) 5.354,0.333 6.615,1.094 1.26,0.76 10 false Master Cylinder Cut Solenoid Valves (2)


Outline of ABS


a.

The ABS prevents the wheels from locking during sudden braking or braking on a slippery surface. This provides the proper braking force when the vehicle slips, thus ensuring vehicle stability and excellent braking performance.

ABS Control (Illustration Provides Conceptual Image)
X113268C02
1.156,1.021 1.458,1.313 0.302,0.292 12 false *A: 1.156,2.417 1.49,2.688 0.333,0.271 12 false *B: 4.604,1.052 4.917,1.208 0.313,0.156 10 false *a
*A With ABS *B Without ABS
*a Brake Operation - -




Outline of EBD


a.

The EBD control utilizes the ABS, realizing the proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during cornering braking, it also controls the brake forces of the right and left wheels, helping to maintain the vehicle behavior.

i.

Front/Rear Wheels Brake Force Distribution

·

This function controls the brake force that acts on the rear wheels in accordance with the changes in the vehicle conditions such as load factors or deceleration, in order to ensure excellent braking performance.

EBD Control Concept
X105343E02
2.406,2.531 2.198,2.531 2.198,2.531 2.198,2.344 true 1.917,1.542 1.552,1.542 1.552,1.542 1.781,2.385 true 5.25,2.49 5.042,2.49 5.042,2.49 5.042,2.302 true 4.76,1.427 4.396,1.427 4.396,1.427 4.792,2.156 true 0.323,2.073 1.042,2.833 0.719,0.76 10 false Rear Brake Force 3.354,2.01 4.063,2.781 0.708,0.771 10 false Rear Brake Force 1.958,1.438 3.833,1.927 1.875,0.49 10 false Ideal Brake Force Distribution 2.438,2.448 3.656,2.844 1.219,0.396 10 false EBD Control 1.51,2.885 2.833,3.271 1.323,0.385 10 false Front Brake Force 1.417,3.323 3.021,3.708 1.604,0.385 10 false Without Load in Rear 4.531,2.885 5.854,3.271 1.323,0.385 10 false Front Brake Force 4.542,3.281 6.146,3.667 1.604,0.385 10 false With Load in Rear 4.792,1.344 6.75,1.74 1.958,0.396 10 false Ideal Brake Force Distribution 5.281,2.406 6.5,2.802 1.219,0.396 10 false EBD Control



ii.

Right/Left Wheels Brake Force Distribution (During Cornering Braking)

·

During cornering braking, this function controls the brake force that acts on the left and right wheels in accordance with the vehicle conditions at that time. This ensures vehicle stability and excellent braking performance.

X105344C01
0,0 0,0 false

V100135

Brake Force
V100136

Control Moment





Outline of Brake Assist


a.

The primary purpose of the brake assist is to provide an auxiliary brake force to assist the driver who cannot generate a large brake force during emergency braking, thus helping draw the vehicle's brake performance.


b.

Based on the signals from the master cylinder pressure sensor, the skid control ECU calculates the speed and the amount of the brake pedal application and then determines the intention of the driver to make an emergency braking. If the skid control ECU determines that the driver intends the emergency braking, this function activates the brake actuator to increase the brake fluid pressure, which increases the brake force.

In case that driver's depressing force is small when applying emergency braking
X128261E01
1.688,1.51 2.969,0.698 2.969,0.698 3.125,0.698 false 0.083,0.583 1.115,1.281 1.031,0.698 10 false Master Cylinder Pressure Sensor Signal 3.188,0.615 5.146,1.333 1.958,0.719 10 false The fluid pressure is increased by brake actuator. 1.385,0.542 2.24,0.979 0.854,0.438 10 false Skid Control ECU 4.719,3.302 6.146,3.615 1.427,0.313 10 false Without Brake Assist 1.396,3.271 2.635,3.729 1.24,0.458 10 false With Brake Assist 0.302,3.938 6.938,4.323 6.635,0.385 10 false There is no difference of the maximum brake performance between the vehicles with and without brake assist. 0.417,6.042 1.25,6.469 0.833,0.427 10 false Brake Force 3.521,8.302 4,8.625 0.479,0.323 10 false Time 3.01,5.385 4.323,5.781 1.313,0.396 10 false With Brake Assist 3.01,6.5 4.375,6.854 1.365,0.354 10 false Without Brake Assist



Outline of TRAC


a.

If the driver presses the accelerator pedal aggressively when initially accelerating or when accelerating on a slippery surface, the drive wheels could slip due to the excessive amount of torque that is generated. By applying hydraulic brake control to the drive wheels and regulating the throttle to control the engine output, TRAC helps minimize the slippage of the drive wheels, thus helping to apply the drive force that is appropriate for the road surface conditions.


b.

For example, a comparison may be made between two vehicles, one with TRAC and the other without. If the driver of each vehicle operates the accelerator pedal in a rough manner while driving over a surface with different surface friction characteristics, the drive wheel on the slippery surface could slip as illustrated. As a result, the vehicle can not start accelerating smoothly.


c.

However, when the vehicle is equipped with TRAC, the skid control ECU instantly determines the state of the vehicle and operates the brake actuator in order to apply the brakes to the slipping drive wheel. Furthermore, the ECM receives the signals from the skid control ECU and regulates the throttle in order to control the engine output. Thus, TRAC can constantly help the driver to maintain stability while accelerating.

HINT:

On the 4WD models, this function operates only when the vehicle is driving in 2WD mode.


Driving condition on road with different surface friction characteristics
X131011C01
1.406,1.948 1.979,1.823 1.979,1.823 1.406,1.688 true 5.396,1.26 6.49,0.656 true 4.958,3.292 4.958,2.229 true 1.177,3.208 1.448,3.479 0.271,0.271 10 false *A 3.167,3.167 3.469,3.396 0.302,0.229 10 false *B 4.875,3.302 5.083,3.521 0.208,0.219 10 false *1 0.771,0.333 1.073,0.615 0.302,0.281 10 false :*a 2.021,1.719 2.281,2.031 0.26,0.313 10 false *b 6.531,0.521 6.802,0.802 0.271,0.281 10 false *c
*A Without TRAC *B With TRAC
*1 Brake Actuator
·

Skid Control ECU


- -
*a Slippery Surface *b Excessive driving force causes the drive wheels to slip
*c Regulating the throttle to control the engine output - -




Outline of A-TRAC


a.

General

i.

When the vehicle drive mode is H4 or L4, the A-TRAC helps restrain wheelspin by controlling the brake fluid pressure that is applied to the spinning wheels, and distributes the drive force that would have been lost through the slippage to the remaining wheels in order to achieve an effect that is similar to LSD.

·

It independently controls the brake fluid pressure to the four wheels in accordance with the extent of the slippage at the wheels, as detected by the skid control ECU.

With A-TRAC
X131012C01
5.167,0.469 5.823,0.25 true 4.74,1.719 5.406,1.229 5.406,1.229 4.771,1.229 true 2.573,1.688 1.677,1.688 1.677,1.688 2.552,1.219 true 1.677,2.448 2.156,2.25 true 3.542,0.917 3.823,1.115 0.281,0.198 10 false *1 3.25,1.719 3.469,1.948 0.219,0.229 10 false *2 3.427,2.042 3.677,2.271 0.25,0.229 10 false *3 3.417,2.563 3.646,2.75 0.229,0.188 10 false *4 4.667,2.313 4.927,2.521 0.26,0.208 10 false *a 4.698,0.042 4.917,0.25 0.219,0.208 10 false *b 1.49,1.573 1.698,1.823 0.208,0.25 10 false *c 1.479,2.354 1.688,2.615 0.208,0.26 10 false *d 2.469,0.125 2.729,0.333 0.26,0.208 10 false *a 2.406,2.438 2.625,2.646 0.219,0.208 10 false *b 5.448,1.115 5.75,1.417 0.302,0.302 10 false *c 5.844,0.125 6.073,0.396 0.229,0.271 10 false *d
*1 Engine *2 Actuator Portion
*3 Skid Control ECU *4 Transfer Position Signal
*a Traction *b Braking
*c Driving Torque *d Snowy or Icy Surface


Without A-TRAC
X131013C01
4.667,1.208 5.458,1.208 true 5.063,0.542 5.583,0.542 true 1.969,1.75 2.49,1.75 true 1.563,2.208 2.083,2.208 true 3.469,0.99 3.708,1.177 0.24,0.188 10 false *1 4.802,1.865 5.031,2.104 0.229,0.24 10 false *a 1.76,1.646 1.979,1.854 0.219,0.208 10 false *b 1.365,2.104 1.583,2.323 0.219,0.219 10 false *c 2.156,0.729 2.385,0.969 0.229,0.24 10 false *a 5.625,0.438 5.865,0.688 0.24,0.25 10 false *c 5.49,1.125 5.729,1.354 0.24,0.229 10 false *b
*1 Engine - -
*a No Traction *b Driving Torque
*c Snowy or Icy Surface - -





b.

Effectiveness of A-TRAC

i.

The effectiveness of A-TRAC is as follows:

·

Off-road drivability that is equivalent to having the center differential locked and limited slip differentials on both front and rear has been realized.

·

This function makes the operation of the differential lock switches basically unnecessary to ensure the ease of driving.

·

While realizing the off-road drivability that is equivalent to having the center and rear differentials locked, as compared to the differential gear in the locked state, the prevention of tight corner braking phenomenon ensures the ease of nimble steerability.





Outline of Auto LSD


a.

Briefly pressing the VSC OFF switch in normal mode allows the Auto LSD to operate (TRAC OFF mode is selected). The Auto LSD achieves the LSD effect by regulating the hydraulic pressure that acts on the drive wheels.

i.

TRAC enhances the start-off performance of the vehicle during low-grip surface conditions, such as snow or mud, by restricting the acceleration effort during a start-off, in order to help prevent the wheels from spinning.


ii.

The Auto LSD enhances the acceleration effort, in order to apply greater drive torque to the wheel that has grip. Thus, this function enables the vehicle to get unstuck if a wheel loses its grip, and enhances the vehicle's start-off performance when high-resistance surface conditions exist, such as loose gravel or sand.

HINT:

On the 4WD models, this function operates only when the vehicle is driving in 2WD mode.


With Auto LSD
X131014C01
4.594,1.448 5.125,0.917 5.125,0.917 4.594,0.917 true 5.021,2.063 5.677,2.063 true 2.542,1.063 2.792,1.313 0.25,0.25 10 false *1 3.24,1.531 3.5,1.729 0.26,0.198 10 false *2 3.396,1.833 3.667,2.052 0.271,0.219 10 false *3 4.042,2.479 4.271,2.708 0.229,0.229 10 false *4 4.5,0.031 4.729,0.24 0.229,0.208 10 false *a 4.479,2.292 4.74,2.51 0.26,0.219 10 false *b 5.719,1.958 5.979,2.208 0.26,0.25 10 false *c 5.167,0.813 5.427,1.052 0.26,0.24 10 false *d
*1 Engine *2 Actuator Portion
*3 Skid Control ECU *4 VSC OFF Switch
*a Traction *b Braking
*c Snowy or Icy Surface *d Driving Torque


Without Auto LSD
X131015C01
4.594,1.635 5.156,1.635 true 5,2.167 5.563,2.167 true 2.521,1.198 2.781,1.438 0.26,0.24 10 false *1 4.74,0.708 4.979,0.948 0.24,0.24 10 false *a 4.438,2.438 4.688,2.656 0.25,0.219 10 false *b 5.594,2.052 5.844,2.302 0.25,0.25 10 false *c 5.208,1.542 5.51,1.771 0.302,0.229 10 false *d
*1 Engine - -
*a No Torque Transferred *b Slipping
*c Snowy or Icy Surface *d Driving Torque





Outline of VSC


a.

The followings are two examples that can be considered as circumstances in which the tires exceed their lateral grip limit. The VSC is designed to help control the vehicle behavior by controlling the engine output and the brakes at each wheel when the vehicle is under one of the conditions indicated below.

·

When the front wheels lose grip in relation to the rear wheels (front wheel skid tendency).

·

When the rear wheels lose grip in relation to the front wheels (rear wheel skid tendency).



X102948C03
2.167,2.281 2.479,2.479 0.313,0.198 10 false *a 4.75,2.25 5.063,2.448 0.313,0.198 10 false *b
*a Front Wheel Skid Tendency *b Rear Wheel Skid Tendency



b.

Method for Determining Vehicle Condition

·

To determine the condition of the vehicle, sensors detect the steering angle, vehicle speed, vehicle's yaw rate, and vehicle's lateral acceleration, which are then calculated by the skid control ECU.


i.

Determining Front Wheel Skid

·

Whether the vehicle is in the state of the front wheel skid or not is determined by the difference between the target yaw rate and the vehicle's actual yaw rate.

·

When the vehicle's actual yaw rate is smaller than the yaw rate (a target yaw rate that is determined by the vehicle speed and steering angle) that should be rightfully generated when the driver operates the steering wheel, it means the vehicle is making a turn at a greater angle than the locus of travel.

·

Thus, the skid control ECU determines that there is a large tendency to front wheel skid.


X105347C02
3.74,0.094 4.146,0.375 0.406,0.281 10 false *a 4.948,0.948 5.354,1.229 0.406,0.281 10 false *b
*a Actual Locus of Travel (Actual Yaw Rate) *b Locus of Travel Based on Target Yaw Rate



ii.

Determining Rear Wheel Skid

·

Whether the vehicle is in the state of the rear wheel skid or not is determined by the values of the vehicle's slip angle and the vehicle's slip angular velocity (time-dependent changes in the vehicle's slip angle). When the vehicle's slip angle and the slip angular velocity are large, the skid control ECU determines that the vehicle has a large rear wheel skid tendency.


X105348C02
3.563,0.115 3.99,0.5 0.427,0.385 10 false *a 4.042,0.115 4.531,0.51 0.49,0.396 10 false *b
*a Travel Direction of Vehicle's Center of Gravity *b Movement of Vehicle
V100136

Slip Angle - -




c.

Method for VSC Operation

·

When the skid control ECU determines that the vehicle has a tendency to front wheel skid or rear wheel skid, it decreases the engine output and applies the brake of a front or rear wheel to control the vehicle's yaw moment. The basic operation of the VSC is described below. However, the control method differs depending on the vehicle's characteristics and driving conditions.


i.

Dampening Front Wheel Skid

·

When the skid control ECU determines that there is a large front wheel skid tendency, it counteracts in accordance with the extent of that tendency. The skid control ECU controls the engine output and applies the brake to the rear wheel of the inner circle of the turn in order to help restrain the front wheel skid tendency.


Dampening a Front Wheel Skid (Marking a Right Turn)
X131053

V100135

Brake Force
V100136

Control Moment


ii.

Dampening Rear Wheel Skid

·

When the skid control ECU determines that there is a large rear wheel skid tendency, it counteracts in accordance with the extent of that tendency. It applies the brakes of the front wheel of the outer circle of the turn, and generates an outward moment of inertia in the vehicle, in order to help restrain the rear wheel skid tendency. Along with the reduction in the vehicle speed caused by the brake force, the excellent vehicle's stability is ensured. In some cases, the skid control ECU applies the brake of the rear wheels as necessary.


Dampening a Rear Wheel Skid (Marking a Right Turn)
X131054

V100135

Brake Force
V100136

Control Moment




Outline of Trailer Sway Control


a.

If the vehicle is towing a trailer with an inappropriate hitch load, trailer sway could be caused by crosswinds, imbalance caused by load, or the driver's steering. Trailer sway control reduces trailer sway by controlling the engine output and the braking of each wheel.

X131055C01
0.563,0.281 0.844,0.552 0.281,0.271 10 false *A 0.583,2.021 0.813,2.25 0.229,0.229 10 false *B 0.688,1.438 0.969,1.719 0.281,0.281 10 false *a 4.531,2.885 4.781,3.188 0.25,0.302 10 false *b
*A Models without Trailer Sway Control *B Models with Trailer Sway Control
*a Side Wind *b Brake Control + Engine Output Control


NOTICE:
·

Trailer sway control is a part of the VSC function. Accordingly, if the VSC OFF Mode or VSC is not functioning normally, trailer sway control will not operate.

·

Trailer sway control will be unable to stabilize the vehicle if a trailer is being towed which cannot be physically controlled due to the influence of the vehicle, road surface, driving conditions and so on.




b.

Trailer Sway Control Operation

i.

The skid control ECU detects the occurrence of trailer sway based on signals from the yaw rate and deceleration sensor and the steering angle sensor.


ii.

Trailer sway can be reduced by decelerating the vehicle. When the skid control ECU detects trailer sway, it controls the brakes of each wheel while simultaneously requesting engine output control from the ECM and reducing vehicle speed.


iii.

Moreover, by using brake control to reduce the yaw moment caused by trailer sway, trailer sway can be reduced more quickly than by simply decelerating the vehicle.


iv.

The slip indicator light on the combination meter flashes when trailer sway control is in operation. Also, the stop light illuminates to inform vehicles behind that the vehicle is decelerating.

X131056C01
2.021,2.083 2.292,2.365 0.271,0.281 10 false *a 2.865,0.271 3.156,0.51 0.292,0.24 10 false *b 5.271,0.927 5.531,1.188 0.26,0.26 10 false *c 5.458,2.375 5.76,2.594 0.302,0.219 10 false *d
*a Trailer Sway *b Deceleration Force Caused by Brake Control and Engine Output Control
*c Yaw Moment Caused by Trailer Sway *d Control Moment Caused by Brake Control


X112414E01
4.385,0.49 4.385,0.292 4.385,0.292 4.792,0.292 false 3.5,1.219 3.906,1.219 3.906,1.219 3.906,1.021 false 0.271,0.583 1.615,1.135 1.344,0.552 10 false Yaw Rate and Lateral Acceleration 0.271,1.531 1.615,2.083 1.344,0.552 10 false Trailer Sway Control 0.271,2.25 1.615,2.802 1.344,0.552 10 false Brake Force 0.271,3.021 1.615,3.573 1.344,0.552 10 false Yaw Moment 0.271,4.01 1.615,4.563 1.344,0.552 10 false Vehicle Speed 6.552,0.74 6.948,1.167 0.396,0.427 10 false Time 6.552,1.698 6.948,2.125 0.396,0.427 10 false Time 6.552,2.333 6.948,2.76 0.396,0.427 10 false Time 6.552,3.115 6.948,3.542 0.396,0.427 10 false Time 6.552,4.385 7.073,4.646 0.521,0.26 10 false Time 4.865,0.208 6.208,0.76 1.344,0.552 10 false Lateral Acceleration 2.865,1.135 3.625,1.5 0.76,0.365 10 false Yaw Rate 4.313,1.375 4.708,1.802 0.396,0.427 10 false On 5.802,1.813 6.198,2.24 0.396,0.427 10 false Off




Layout of Main Components


X131057C01
4.365,2.208 5.594,0.375 true 5.771,2.031 6.5,1.313 true 5.906,3.594 5.469,2.823 true 1.979,4.302 2.375,3.688 true 0.49,3.427 1.396,3.01 true 0.323,3.323 0.552,3.583 0.229,0.26 10 false *1 1.865,4.292 2.135,4.542 0.271,0.25 10 false *2 5.885,3.594 6.146,3.875 0.26,0.281 10 false *3 6.51,1.188 7.073,1.521 0.563,0.333 10 false *4 (*A) 5.563,0.188 5.865,0.448 0.302,0.26 10 false *5
*A Models with Rear Air Suspension System - -
*1 Front Speed Sensor RH *2 Front Speed Sensor LH
*3 Rear Speed Sensor LH *4 Suspension Control ECU
*5 Rear Speed Sensor RH - -


X131058C01
1.573,0.813 2.708,1.302 true 4.469,1.281 4.75,0.385 true 4.719,1.375 5.802,0.938 true 4.781,1.542 5.781,1.938 true 1.406,0.698 1.635,0.958 0.229,0.26 10 false *1 5.823,1.885 6.083,2.135 0.26,0.25 10 false *2 5.833,0.833 6.104,1.083 0.271,0.25 10 false *3 4.719,0.198 4.979,0.458 0.26,0.26 10 false *4
*1 ECM *2 Engine Room R/B
·

BRK No. 1 Relay

·

BRK No. 2 Relay


*3 Brake Actuator
·

Skid Control ECU

·

Master Cylinder Pressure Sensor


*4 Brake Booster
·

Booster Solenoid

·

Micro Switch

·

Booster Stroke Sensor




X131059C01
2.542,2.042 1.865,0.927 true 0.917,1.479 2.292,2.26 true 0.802,3.406 2.698,2.75 true 1.354,5.25 1.771,4.833 true 4,4.938 3.615,4.177 true 5.115,2.406 6.104,1.75 true 1.74,0.75 1.99,1 0.25,0.25 10 false *1 0.74,1.365 0.969,1.615 0.229,0.25 10 false *2 0.625,3.333 0.875,3.625 0.25,0.292 10 false *3 1.229,5.25 1.448,5.51 0.219,0.26 10 false *4 3.958,4.948 4.188,5.208 0.229,0.26 10 false *5 6.125,1.635 6.75,1.958 0.625,0.323 10 false *6 (*A) 3.625,1.26 3.865,1.49 0.24,0.229 10 false *7
*A 4WD Models - -
*1 Combination Meter Assembly *2 Steering Angle Sensor
*3 DLC3 *4 Stop Light Switch
*5 Yaw Rate and Deceleration Sensor *6 4WD Control ECU
*7 VSC OFF Switch - -



Function of Main Components


Component Function

*: 4WD models

Combination Meter Assembly ABS Warning Light Lights up to alert the driver that the skid control ECU detects a malfunction in the ABS, EBD or brake assist system.
Brake System Warning Light
·

Lights up together with the ABS warning light to alert the driver that the skid control ECU detects a malfunction in the EBD or when a malfunction occurs in the brake booster.

·

Lights up to alert the driver that the brake fluid level is low.

·

Lights up to alert the driver that the parking brake is applied.


Slip Indicator Light
·

Blinks to inform the driver that the TRAC, A-TRAC, Auto LSD, VSC or trailer sway control is operated.

·

Lights up to alert the driver that the skid control ECU detects a malfunction in the TRAC, A-TRAC, Auto LSD or VSC.


TRAC OFF Indicator Light Lights up to inform the driver when the TRAC OFF mode is entered using the VSC OFF switch.
VSC OFF Indicator Light
·

Lights up to inform the driver that the VSC OFF mode is selected using the VSC OFF switch.

·

When the skid control ECU detects a malfunction and determines that the TRAC, A-TRAC, Auto LSD, VSC or trailer sway control is not available, the VSC OFF indicator light blinks to alert the driver.


Auto LSD IndicatorLight Lights up to inform the driver that the Auto LSD mode is selected using the VSC OFF switch.
Brake Actuator Actuator Portion Changes the fluid path based on the signals from the skid control ECU during the operation of the ABS, EBD, brake assist, TRAC, A-TRAC, Auto LSD, VSC and trailer sway control, in order to control the fluid pressure that is applied to the brakes for the different wheels.
Master Cylinder Pressure Sensor Detects the master cylinder pressure.
Solenoid Relay Controls power supplied to the solenoid valves.
Motor Relay Supplies power to the pump motor in the brake actuator.
Skid Control ECU
·

Judges the vehicle driving conditions based on signals from each sensor, and sends brake control signals to the brake actuator.

·

Judges the vehicle driving conditions based on signals from each sensor, and calculates the amount of engine output adjustment required. The skid control ECU transmits command signals to the ECM.


Brake Booster Booster Solenoid When the VSC is activated, this solenoid operates in accordance with the signals from the skid control ECU to boost the hydraulic pressure to the wheel cylinders.
Micro Switch Detects that the brake pedal is depressed.
Booster Stroke Sensor Detects the brake pedal stroke distance.
Speed Sensor Detects the wheel speed of each of the four wheels.
Yaw Rate and Deceleration Sensor
·

Detects the vehicle's yaw rate.

·

Detects the vehicle's lateral acceleration (2WD models).

·

Detects the vehicle's longitudinal and lateral acceleration (4WD models).


Steering Angle Sensor Detects the steering direction and angle of the steering wheel.
VSC OFF Switch
·

Cancels the TRAC or VSC.

·

Selects the 4 modes (Normal mode, TRAC OFF mode, Auto LSD mode, VSC OFF mode).


Parking Brake Switch Detects parking brake application.
Stop Light Switch Detects brake pedal application.
4WD Control ECU* Detects the transfer shift position (H4 or L4) and sends the information to the skid control ECU.
ECM
·

Sends the throttle valve angle signal, accelerator pedal position signal, engine speed signal, and intake air temperature signal to the skid control ECU.

·

Receives an engine output adjustment command signals from the skid control ECU. Based on these signals, the ECM operates the throttle valve to control engine output.




Brake Booster


a.

General

i.

When the VSC is activated, the booster solenoid that is enclosed in the brake booster moves the air valve to regulate the amount of pressure applied by the master cylinder. At this time, the skid control ECU controls the booster solenoid in accordance with the signals from the master cylinder pressure sensor. Thus, the brake fluid pressure is supplemented when the VSC is activated, resulting in excellent brake control.


ii.

Because the brake pedal could move down with the activation of the VSC, the fact that the driver is depressing the brake pedal is determined by the release switch that is enclosed in the brake booster.


iii.

The booster stroke sensor is used to detect a malfunction of the active brake booster. If the booster malfunctions, the brake assist system will be activated to assist the braking force.

System Diagram
X131020E01
5.104,2.802 6.729,3.229 1.625,0.427 10 false Booster Stroke Sensor 5.396,1.865 6.573,2.229 1.177,0.365 10 false Micro Switch 5.313,0.917 6.635,1.333 1.323,0.417 10 false Booster Solenoid 5.406,0.344 6.5,0.719 1.094,0.375 10 false Brake Booster 3.177,1.625 3.969,2.573 0.792,0.948 10 false Skid Control ECU 0.313,0.375 1.469,0.813 1.156,0.438 10 false Brake Actuator 0.479,1.708 2.594,2.104 2.115,0.396 10 false Master Cylinder Pressure Sensor



b.

Construction

i.

The brake booster mainly consists of the push rod, air valve, booster solenoid, booster solenoid case, release switch, push ring, push plate and booster stroke sensor.

X131021C01
2.583,1.271 2.344,0.417 true 3.604,1.708 4.031,0.552 true 6.406,2.74 5.969,1.969 true 3.01,3.281 2.615,2.354 true 2.365,3.365 2.365,2.281 true 1.625,3.26 2.083,2.5 true 0.542,1.01 1.698,1.802 true 2.083,1.5 1.208,0.448 true 2.24,0.198 2.479,0.406 0.24,0.208 10 false *1 1.083,0.25 1.323,0.458 0.24,0.208 10 false *2 0.385,0.875 0.594,1.125 0.208,0.25 10 false *3 1.521,3.25 1.729,3.458 0.208,0.208 10 false *4 2.302,3.365 2.573,3.594 0.271,0.229 10 false *5 2.969,3.281 3.26,3.51 0.292,0.229 10 false *6 6.365,2.74 6.646,3.042 0.281,0.302 10 false *7 0.552,1.781 0.74,2 0.188,0.219 10 false *a 6.385,1.823 6.573,2.052 0.188,0.229 10 false *b 3.979,0.323 4.24,0.552 0.26,0.229 10 false *8
*1 Booster Stroke Sensor *2 Push Ring
*3 Push Plate *4 Release Switch
*5 Booster Solenoid *6 Booster Solenoid Case
*7 Push Rod *8 Air Valve
*a To Master Cylinder *b From Brake Pedal




c.

Operation

i.

Normal Braking

·

During normal braking, the input load from the brake pedal is transmitted to the push rod, air valve, booster solenoid case, push ring, push plate, and reaction disc, and then output to the master cylinder.

·

At this time, the air valve moves, and air flows into the variable pressure chamber. This creates a pressure difference between the constant pressure chamber and the variable pressure chamber, and the input load from the brake pedal is amplified and output to the master cylinder.


X131022C01
3.021,0.865 3.302,0.448 true 2.313,0.896 2.313,0.385 true 1.76,0.854 1.594,0.427 true 2.031,1.51 0.646,0.719 true 0.542,1.375 1.688,1.823 true 0.625,2.458 1.333,2.198 true 2.167,3.292 2.615,2.354 true 4.125,3.031 3.844,2.177 true 6.5,2.594 5.958,2 true 2.24,0.198 2.479,0.396 0.24,0.198 10 false *1 0.479,0.573 0.708,0.813 0.229,0.24 10 false *2 0.385,1.25 0.615,1.479 0.229,0.229 10 false *3 0.458,2.385 0.677,2.625 0.219,0.24 10 false *4 2.094,3.292 2.333,3.531 0.24,0.24 10 false *5 6.479,2.594 6.708,2.813 0.229,0.219 10 false *6 1.479,0.208 1.719,0.448 0.24,0.24 10 false *a 0.604,1.802 0.813,2.042 0.208,0.24 10 false *b 4.094,3.031 4.354,3.271 0.26,0.24 10 false *c 6.396,1.802 6.677,2.052 0.281,0.25 10 false *d 3.25,0.229 3.49,0.469 0.24,0.24 10 false *a
*1 Constant Pressure Chamber *2 Push Ring
*3 Push Plate *4 Release Switch
*5 Booster Solenoid Case *6 Push Rod
*a Variable Pressure Chamber *b To Master Cylinder
*c Air Valve "Open" *d From Brake Pedal



ii.

VSC Operation

·

When the VSC is activated, current flows to the booster solenoid in accordance with the signals from the skid control ECU. The booster solenoid core and the control valve then move toward the brake pedal, thus moving the valve seat toward the brake pedal.

·

As a result, the air valve opens and air flows into the variable pressure chamber. This creates a pressure difference between the constant pressure chamber and the variable pressure chamber. The pressure difference causes the brake booster to activate and output to the master cylinder.

·

VSC operation may cause the brake pedal to move downward. A stop light inhibit relay is provided to prevent undesired operation of the stop lights due to operation of VSC.


X131023C01
3.938,1.542 4.615,0.583 true 3.552,1.583 3.906,0.552 true 2.99,0.865 3.156,0.354 true 2.302,0.958 2.302,0.323 true 1.719,0.865 1.5,0.323 true 1.854,3.135 2.125,2.052 true 2.375,3.188 2.375,2.26 true 6.469,2.552 6.083,1.979 true 4.104,2.99 3.865,2.177 true 2.219,0.104 2.469,0.302 0.25,0.198 10 false *1 1.76,3.146 2.031,3.385 0.271,0.24 10 false *2 2.302,3.198 2.552,3.469 0.25,0.271 10 false *3 6.417,2.563 6.677,2.833 0.26,0.271 10 false *4 4.594,0.417 4.844,0.656 0.25,0.24 10 false *5 3.865,0.354 4.094,0.583 0.229,0.229 10 false *6 3.125,0.146 3.344,0.375 0.219,0.229 10 false *a 0.594,1.802 0.823,2.052 0.229,0.25 10 false *b 4.052,2.979 4.302,3.25 0.25,0.271 10 false *c 1.396,0.125 1.646,0.323 0.25,0.198 10 false *a
*1 Constant Pressure Chamber *2 Booster Solenoid Core
*3 Booster Solenoid *4 Push Rod
*5 Valve Seat *6 Control Valve
*a Variable Pressure Chamber *b To Master Cylinder
*c Air Valve "Open" - -





VSC OFF Switch


a.

4WD Models (in 2WD Mode) and 2WD Models

i.

The VSC OFF switch can select the 4 modes (Normal mode, TRAC OFF mode, Auto LSD mode, VSC OFF mode).


ii.

Briefly pressing the VSC OFF switch in Normal mode selects the TRAC OFF mode, turning the Auto LSD ON (standby).


iii.

Pressing and holding the VSC OFF switch for 3 seconds or more with the vehicle stopped selects the Auto LSD mode, disabling the TRAC and VSC functions.


iv.

In the Auto LSD mode, pressing and holding the VSC OFF switch for 3 seconds or more with the vehicle stopped selects the VSC OFF mode, disabling all functions.


v.

After the ignition switch is turned OFF in the TRAC OFF mode, Auto LSD mode or VSC OFF mode, turning the ignition switch ON again selects the Normal mode.

X131060C01
3.479,0.365 3.74,0.625 0.26,0.26 10 false *a 2.365,1.302 2.635,1.51 0.271,0.208 10 false *b 3.531,2.219 3.76,2.51 0.229,0.292 10 false *c 4.698,1.281 4.948,1.563 0.25,0.281 10 false *d 5.667,1.875 6.083,2.125 0.417,0.25 10 false : *e 5.677,2.313 6.125,2.604 0.448,0.292 10 false : *f
*a Normal Mode *b TRAC OFF Mode (Auto LSD ON)
*c Auto LSD Mode *d VSC OFF Mode
*e VSC OFF Switch Operation (Briefly press) *f VSC OFF Switch Operation (Press and hold for 3 seconds or more)



vi.

The operation of the brake control functions and the illumination state of the respective indicator lights in each mode are as follows:

2WD Models
Item Brake Control Function Indicator Light
TRAC TRAC Auto LSD VSC TRAC OFF Indicator Light Auto LSD Indicator Light VSC OFF Indicator Light

○ : Controlled

-: Not controlled

*: When the vehicle is braking or the yaw rate is large, the VSC will operate even in the VSC OFF mode.

Normal Mode ○ - ○ Off Off Off
TRAC OFF Mode - ○ ○ Off On Off
Auto LSD Mode - ○ - Off On On
VSC OFF Mode - - -* On Off On

4WD Models (in 2WD Mode)
Item Brake Control Function Indicator Light
TRAC A-TRAC Auto LSD VSC TRAC OFF Indicator Light Auto LSD Indicator Light VSC OFF Indicator Light

○ : Controlled

-: Not controlled

*: When the vehicle is braking or the yaw rate is large, the VSC will operate even in the VSC OFF mode.

Normal Mode ○ - - ○ Off Off Off
TRAC OFF Mode - - ○ ○ Off On Off
Auto LSD Mode - - ○ - Off On On
VSC OFF Mode - - - -* On Off On



b.

4WD Models (in 4WD Mode)

i.

The VSC OFF switch can select the 3 modes (Normal mode, TRAC OFF mode*, VSC OFF mode).


ii.

Briefly pressing the VSC OFF switch in Normal mode selects the TRAC OFF mode*.


iii.

Pressing and holding the VSC OFF switch for 3 seconds or more with the vehicle stopped selects the VSC OFF mode, disabling the TRAC and VSC functions.


iv.

Briefly pressing the VSC OFF switch in the TRAC OFF mode* or VSC OFF mode or turning the ignition switch OFF returns to the Normal mode.

HINT:

*: The driver can't choose the TRAC OFF mode when the transfer is in the H4L, L4F or L4L mode.


X131061C01
3.552,0.51 3.875,0.813 0.323,0.302 10 false *a 2.5,1.479 2.76,1.75 0.26,0.271 10 false *b 4.604,1.49 4.917,1.74 0.313,0.25 10 false *c 6.01,1.865 6.406,2.167 0.396,0.302 10 false : *d 6.01,2.292 6.323,2.615 0.313,0.323 10 false : *e
*a Normal Mode *b TRAC OFF Mode
*c VSC OFF Mode *d VSC OFF Switch Operation (Briefly press)
*e VSC OFF Switch Operation (Press and hold for 3 seconds or more) - -



v.

The operation of the brake control functions and the illumination state of the respective indicator lights in each mode are as follows:

4WD Models (in 4WD Mode)
Item Brake Control Function Indicator Light
TRAC A-TRAC Auto LSD VSC TRAC OFF Indicator Light Auto LSD Indicator Light VSC OFF Indicator Light

○ : Controlled

-: Not controlled

*: When the vehicle is braking or the yaw rate is large, the VSC will operate even in the VSC OFF mode.

H4F Normal Mode - ○ - ○ Off Off Off
TRAC OFF Mode - - - ○ On Off Off
VSC OFF Mode - - - -* On Off On
L4F Normal Mode - ○ - ○ Off Off Off
VSC OFF Mode - - - - On Off On
H4L L4L Normal Mode - ○ - - Off Off On
VSC OFF Mode - - - - On Off On




Yaw Rate and Deceleration Sensor


a.

A deceleration sensor is built into the yaw rate sensor.


b.

This sensor detects the yaw rate and lateral and longitudinal* acceleration and deceleration.

*: 4WD models


X131062

HINT:

After replacing the yaw rate and deceleration sensor or the skid control ECU, initialization of the yaw rate and deceleration sensor is required. For details, refer to the Repair Manual.




Brake Actuator


a.

The brake actuator consists of the actuator portion and skid control ECU.


b.

The actuator portion consists of 12 solenoid valves, pump motor, 2 pumps, 2 reservoirs, and master cylinder pressure sensor.


c.

The 12 solenoid valves consists of 2 master cylinder cut solenoid valves [(1), (4)], 2 reservoir cut solenoid valves [(2), (3)], 4 pressure holding solenoid valves [(5), (6), (7), (8)], and 4 pressure reduction solenoid valves [(9), (10), (11), (12)].

X131063C01
3.208,4.135 3.583,5 3.583,5 3.969,4.146 true 3.198,5.573 3.552,6.104 3.552,6.104 3.979,5.583 true 0.729,0.531 0.979,0.74 0.25,0.208 10 false *1 5.135,0.938 5.385,1.156 0.25,0.219 10 false *2 3.51,5.01 3.76,5.271 0.25,0.26 10 false *3 3.479,6.125 3.75,6.375 0.271,0.25 10 false *4 1.198,0.208 1.438,0.438 0.24,0.229 10 false *a 1.354,6.458 1.583,6.677 0.229,0.219 10 false *b 2.333,6.458 2.583,6.708 0.25,0.25 10 false *c 4.688,6.458 4.948,6.698 0.26,0.24 10 false *d 5.646,6.458 5.906,6.688 0.26,0.229 10 false *e 1.396,2.604 1.646,2.896 0.25,0.292 10 false (1) 2.76,2.594 3.01,2.885 0.25,0.292 10 false (2) 4.26,2.594 4.51,2.885 0.25,0.292 10 false (3) 5.625,2.604 5.875,2.896 0.25,0.292 10 false (4) 5.677,3.927 5.948,4.135 0.271,0.208 10 false (8) 4.719,3.927 4.948,4.156 0.229,0.229 10 false (7) 1.375,3.927 1.625,4.156 0.25,0.229 10 false (5) 2.333,3.927 2.615,4.146 0.281,0.219 10 false (6) 1.417,5 1.688,5.24 0.271,0.24 10 false (9) 2.292,5 2.646,5.26 0.354,0.26 10 false (10) 4.698,5 5.031,5.292 0.333,0.292 10 false (11) 5.615,5.01 5.958,5.292 0.344,0.281 10 false (12) 5.792,0.198 6.031,0.427 0.24,0.229 10 false *a
*1 Brake Actuator *2 Master Cylinder Pressure Sensor
*3 Pump *4 Reservoir
*a From Master Cylinder *b Rear Left
*c Rear Right *d Front Left
*e Front Right - -


Item
(1), (4) Master Cylinder Cut Solenoid Valve
(2), (3) Reservoir Cut Solenoid Valve
(5), (6), (7), (8) Pressure Holding Solenoid Valve
(9), (10), (11), (12) Pressure Reduction Solenoid Valve



System Operation


a.

Normal Braking

i.

During normal braking, all solenoid valves are turned OFF.

X131064C01
3.198,4.104 3.573,4.958 3.573,4.958 3.948,4.115 true 3.188,5.521 3.563,6.25 3.563,6.25 3.938,5.552 true 0.75,0.458 0.958,0.667 0.208,0.208 10 false *1 5.146,0.917 5.375,1.135 0.229,0.219 10 false *2 3.51,4.99 3.781,5.229 0.271,0.24 10 false *3 3.479,6.271 3.74,6.542 0.26,0.271 10 false *4 1.188,0.25 1.448,0.469 0.26,0.219 10 false *a 1.385,6.427 1.615,6.688 0.229,0.26 10 false *b 2.313,6.427 2.531,6.719 0.219,0.292 10 false *c 4.698,6.427 4.927,6.698 0.229,0.271 10 false *d 5.635,6.417 5.875,6.688 0.24,0.271 10 false *e 1.385,4.979 1.75,5.271 0.365,0.292 10 false (9) 2.281,4.958 2.646,5.167 0.365,0.208 10 false (10) 4.667,4.958 5,5.167 0.333,0.208 10 false (11) 5.615,4.969 5.948,5.208 0.333,0.24 10 false (12) 5.656,3.885 5.958,4.115 0.302,0.229 10 false (8) 4.688,3.885 4.99,4.104 0.302,0.219 10 false (7) 2.323,3.885 2.667,4.094 0.344,0.208 10 false (6) 1.385,3.885 1.667,4.115 0.281,0.229 10 false (5) 1.385,2.563 1.667,2.854 0.281,0.292 10 false (1) 2.76,2.552 3.073,2.792 0.313,0.24 10 false (2) 4.26,2.563 4.583,2.792 0.323,0.229 10 false (3) 5.625,2.563 5.896,2.802 0.271,0.24 10 false (4) 5.823,0.24 6.083,0.458 0.26,0.219 10 false *a
*1 Brake Actuator *2 Master Cylinder Pressure Sensor
*3 Pump *4 Reservoir
*a From Master Cylinder *b Rear Left
*c Rear Right *d Front Left
*e Front Right - -


Item
(1), (4) Master Cylinder Cut Solenoid Valve
(2), (3) Reservoir Cut Solenoid Valve
(5), (6), (7), (8) Pressure Holding Solenoid Valve
(9), (10), (11), (12) Pressure Reduction Solenoid Valve



b.

ABS and EBD Operation

i.

Based on the signals received from the four wheel speed sensors and yaw rate and deceleration sensor, the skid control ECU calculates the wheel rotation speed and deceleration for each wheel, in order to check for a wheel slippage condition. According to the slippage condition, the skid control ECU controls the pressure holding solenoid valves and pressure reduction solenoid valves in order to adjust the fluid pressure of the brakes for each of the wheels in the following three modes: pressure reduction, pressure holding, and pressure increase modes.

X102082C05
2.792,0.667 3.594,0.958 true 2.927,2.792 3.594,2.521 true 1.229,1.635 1.448,1.875 0.219,0.24 10 false *1 1.24,3.198 1.49,3.448 0.25,0.25 10 false *2 2.604,0.542 2.823,0.823 0.219,0.281 10 false *3 2.729,2.698 2.938,2.938 0.208,0.24 10 false *4 1.219,0.167 1.49,0.385 0.271,0.219 10 false *a 3.563,0.156 3.844,0.375 0.281,0.219 10 false *b 5.802,0.208 6.042,0.427 0.24,0.219 10 false *c 1.781,3.365 2.052,3.615 0.271,0.25 10 false *d 5.063,1.99 5.302,2.208 0.24,0.219 10 false *e 6.354,3.365 6.563,3.604 0.208,0.24 10 false *f
*1 Pressure Holding Solenoid Valve *2 Pressure Reduction Solenoid Valve
*3 Port A *4 Port B
*a Pressure Increase Mode *b Pressure Holding Mode
*c Pressure Reduction Mode *d To Wheel Cylinder
*e To Reservoir and Pump *f From Wheel Cylinder


Brake Actuator Operation in ABS and EBD
Pressure Mode Pressure Increase Mode Pressure Holding Mode Pressure Reduction Mode
Pressure Holding Solenoid Valve (Port A) Off (Open) On (Closed) On (Closed)
Pressure Reduction Solenoid Valve (Port B) Off (Closed) Off (Closed) On (Open)
Wheel Cylinder Pressure Increase Hold Reduce



c.

Brake Assist Operation

i.

In the event of emergency braking, the skid control ECU detects the driver's intention based on the speed of the pressure increase in the master cylinder determined by the master cylinder pressure sensor signals. If the skid control ECU judges the need for additional brake assist, pressure is generated by the pump in the brake actuator and directed to the brakes to apply a greater fluid pressure than the master cylinder. Also, in the following case, the skid control ECU provides brake assist.


ii.

In the event of a brake booster failure, the skid control ECU judges the failure using the booster stroke sensor in the brake booster and master cylinder pressure sensor signals.

X131065C01
1.01,2.906 1.448,3.417 true 0.573,4.125 1.458,4.49 true 1.958,5.396 2.385,4.479 true 2.396,3.417 2.135,2.75 true 3.198,5.583 3.573,6.177 3.573,6.177 3.958,5.594 true 5.167,5.469 4.771,4.479 true 5.708,4.49 6.615,4.167 true 5.698,2.052 6.125,1.927 true 4.323,2.052 4.74,1.875 true 2.271,1.906 2.823,2.052 true 1,1.948 1.458,2.083 true 5.708,3.396 6.104,2.917 true 4.771,3.396 5.042,2.771 true 3.208,4.156 3.583,4.823 3.583,4.823 3.969,4.167 true 0.74,0.552 0.979,0.75 0.24,0.198 10 false *1 5.146,0.927 5.396,1.135 0.25,0.208 10 false *2 3.51,4.833 3.74,5.063 0.229,0.229 10 false *3 3.5,6.188 3.719,6.448 0.219,0.26 10 false *4 1.167,0.198 1.406,0.396 0.24,0.198 10 false *a 1.385,6.458 1.594,6.677 0.208,0.219 10 false *b 2.323,6.448 2.531,6.698 0.208,0.25 10 false *c 4.698,6.458 4.896,6.688 0.198,0.229 10 false *d 5.635,6.448 5.844,6.656 0.208,0.208 10 false *e 5.823,0.198 6.063,0.396 0.24,0.198 10 false *a 1.365,2.615 1.677,2.813 0.313,0.198 10 false (1) 2.708,2.594 3.021,2.792 0.313,0.198 10 false (2) 4.271,2.594 4.563,2.823 0.292,0.229 10 false (3) 5.635,2.604 5.948,2.802 0.313,0.198 10 false (4) 5.656,3.917 5.969,4.115 0.313,0.198 10 false (8) 4.719,3.927 5.031,4.125 0.313,0.198 10 false (7) 2.344,3.938 2.656,4.135 0.313,0.198 10 false (6) 1.375,3.938 1.688,4.135 0.313,0.198 10 false (5) 1.385,5.01 1.656,5.292 0.271,0.281 10 false (9) 2.323,5 2.656,5.229 0.333,0.229 10 false (10) 4.667,5 4.979,5.198 0.313,0.198 10 false (11) 5.604,5.01 5.948,5.229 0.344,0.219 10 false (12) 6.656,4.052 6.917,4.302 0.26,0.25 10 false (L) 6.177,1.813 6.427,2.083 0.25,0.271 10 false (D) 4.781,1.76 5.063,2.031 0.281,0.271 10 false (C) 2.052,1.771 2.302,2.031 0.25,0.26 10 false (B) 0.771,1.823 1.031,2.073 0.26,0.25 10 false (A) 0.844,2.698 1.135,2.938 0.292,0.24 10 false (E) 2.052,2.573 2.333,2.792 0.281,0.219 10 false (F) 4.958,2.604 5.25,2.823 0.292,0.219 10 false (G) 6.031,2.75 6.354,2.99 0.323,0.24 10 false (H) 5.146,5.479 5.438,5.708 0.292,0.229 10 false (K) 1.865,5.406 2.135,5.625 0.271,0.219 10 false (J) 0.417,3.979 0.604,4.24 0.188,0.26 10 false (I)
*1 Brake Actuator *2 Master Cylinder Pressure Sensor
*3 Pump *4 Reservoir
*a From Master Cylinder *b Rear Left
*c Rear Right *d Front Left
*e Front Right - -


Brake Actuator Operation in Brake Assist
Item Brake Assist Not Activated Brake Assist Activated
Pump Off On
Master Cylinder Cut Solenoid Valve (1) Port (A) Off (Open) On (Closed)
(4) Port (D) Off (Open) On (Closed)
Reservoir Cut Solenoid Valve (2) Port (B) Off (Closed) On (Open)
(3) Port (C) Off (Closed) On (Open)
Pressure Holding Solenoid Valve (5) Port (E) Off (Open) ←
(6) Port (F) Off (Open) ←
(7) Port (G) Off (Open) ←
(8) Port (H) Off (Open) ←
Pressure Reduction Solenoid Valve (9) Port (I) Off (Closed) ←
(10) Port (J) Off (Closed) ←
(11) Port (K) Off (Closed) ←
(12) Port (L) Off (Closed) ←



d.

TRAC Operation

i.

The fluid pressure generated by the pump is regulated by the master cylinder cut solenoid valve to the required pressure. Thus, the wheel cylinders of the drive wheels are controlled in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes to control the slippage of the drive wheels.


ii.

The TRAC operation diagram shows the hydraulic circuit in the pressure increase mode when the TRAC is activated.


iii.

The pressure holding solenoid valve and the pressure reduction solenoid valve are turned on/off according to the ABS with EBD operation pattern.

X131066C01
1,1.854 1.458,2.031 true 3.198,4.125 3.583,4.906 3.583,4.906 3.969,4.125 true 2.323,1.823 2.833,2 true 5.708,2.031 6.146,1.875 true 5.708,3.375 6.125,2.927 true 4.771,3.385 4.948,2.729 true 2.406,3.385 2.188,2.719 true 1.458,3.354 1.01,2.875 true 0.573,4.177 1.458,4.438 true 2,5.458 2.396,4.438 true 5.208,5.375 4.76,4.438 true 5.708,4.448 6.563,4.208 true 3.188,5.531 3.552,6.208 3.552,6.208 3.958,5.531 true 4.333,2.021 4.792,1.875 true 0.76,0.479 0.99,0.667 0.229,0.188 10 false *1 5.146,0.906 5.406,1.115 0.26,0.208 10 false *2 3.51,4.917 3.74,5.125 0.229,0.208 10 false *3 3.469,6.229 3.719,6.448 0.25,0.219 10 false *4 1.198,0.229 1.406,0.438 0.208,0.208 10 false *a 1.385,6.458 1.573,6.729 0.188,0.271 10 false *b 2.344,6.427 2.615,6.635 0.271,0.208 10 false *c 4.688,6.438 4.948,6.677 0.26,0.24 10 false *d 5.635,6.427 5.865,6.677 0.229,0.25 10 false *e 1.375,2.563 1.667,2.802 0.292,0.24 10 false (1) 2.76,2.552 3.063,2.781 0.302,0.229 10 false (2) 4.26,2.552 4.563,2.781 0.302,0.229 10 false (3) 5.625,2.563 5.896,2.792 0.271,0.229 10 false (4) 6.188,1.771 6.448,2.052 0.26,0.281 10 false (D) 4.823,1.76 5.125,2.052 0.302,0.292 10 false (C) 2.115,1.698 2.375,1.969 0.26,0.271 10 false (B) 0.771,1.729 1.042,1.979 0.271,0.25 10 false (A) 0.917,2.698 1.188,2.896 0.271,0.198 10 false (E) 2.115,2.552 2.375,2.75 0.26,0.198 10 false (F) 1.375,3.896 1.688,4.115 0.313,0.219 10 false (5) 2.313,3.885 2.563,4.073 0.25,0.188 10 false (6) 4.708,3.885 5.01,4.115 0.302,0.229 10 false (7) 5.646,3.885 5.948,4.094 0.302,0.208 10 false (8) 4.865,2.563 5.167,2.792 0.302,0.229 10 false (G) 6.052,2.771 6.354,2.99 0.302,0.219 10 false (H) 6.604,4.094 6.906,4.365 0.302,0.271 10 false (L) 4.667,4.958 5.01,5.156 0.344,0.198 10 false (11) 2.26,4.958 2.594,5.177 0.333,0.219 10 false (10) 1.323,4.969 1.625,5.24 0.302,0.271 10 false (9) 0.406,4.042 0.625,4.281 0.219,0.24 10 false (I) 1.875,5.458 2.156,5.677 0.281,0.219 10 false (J) 5.146,5.375 5.438,5.625 0.292,0.25 10 false (K) 5.594,4.969 5.917,5.208 0.323,0.24 10 false (12) 5.823,0.229 6.031,0.438 0.208,0.208 10 false *a
*1 Brake Actuator *2 Master Cylinder Pressure Sensor
*3 Pump *4 Reservoir
*a From Master Cylinder *b Rear Left
*c Rear Right *d Front Left
*e Front Right - -


Brake Actuator Operation in TRAC
Item TRAC Operation
Not Activated Pressure Increase Mode Pressure Holding Mode Pressure Reduction Mode
Pump Off On ← ←
Master Cylinder Cut Solenoid Valve (1) Port (A) Off (Open) On (Closed) ← Off (Open)
(4) Port (D) Off (Open) ← ← ←
Reservoir Cut Solenoid Valve (2) Port (B) Off (Closed) On (Open) ← Off (Closed)
(3) Port (C) Off (Closed) ← ← ←
Front Brake Pressure Holding Solenoid Valve (7) Port (G) Off (Open) ← ← ←
(8) Port (H) Off (Open) ← ← ←
Pressure Reduction Solenoid Valve (11) Port (K) Off (Closed) ← ← ←
(12) Port (L) Off (Closed) ← ← ←
Rear Brake Pressure Holding Solenoid Valve (5) Port (E) Off (Open) ← On (Closed) Off (Open)
(6) Port (F) Off (Open) ← On (Closed) Off (Open)
Pressure Reduction Solenoid Valve (9) Port (I) Off (Closed) ← ← ←
(10) Port (J) Off (Closed) ← ← ←



e.

A-TRAC Operation

i.

Based on the vehicle speed that has been calculated from each speed sensor and the signals of the yaw rate and deceleration sensor, the skid control ECU computes the target control speed.


ii.

The skid control ECU compares the target control speed and the speeds of the wheels to determine whether or not slippage exists. Upon detecting slippage, the skid control ECU controls the solenoid valves of the brake actuator to control the brake fluid pressure that is applied to the slipping wheel. When the wheel speed becomes lower than the target control speed, the skid control ECU stops increasing the brake fluid pressure.


iii.

The target control speed and the brake control are as shown in the table below.

Road Condition Transfer Range Control Outline
Ordinary H4 Target Control Speed Vehicle Speed + Slip Rate (H4 range set value) Control designed to ensure the ease of driving on low-friction roads, dirt roads, and general roads.
Brake Control Gradual fluid Pressure Control
Rocky or Offroad L4 Target Control Speed Vehicle Speed + Slip Rate (L4 range set value) Control designed for rugged off-road driving conditions.
Brake Control Sudden fluid Pressure Control

NOTICE:
·

When the A-TRAC is operating continuously while the vehicle is being driven on a slippery surface, the temperature of the brake pads increases. After a set length of time elapses, the skid control ECU alerts the driver of this condition by causing the buzzer to sound, and the slip indicator warning light to illuminate. Also, the A-TRACoperation is temporarily interrupted to protect the pads.

·

When the temperature of the pads decreases, the slip indicator light turns off, and the A-TRAC is automatically restored to an operating state.




iv.

The A-TRAC operation diagram shows the hydraulic circuit in the pressure increase mode when the A-TRAC is activated.

A-TRAC Operation (When wheelspin of the front left wheel and rear right wheel occurs)
X131067C01
1.042,1.896 1.448,2.031 true 2.281,1.865 2.823,2.021 true 4.323,2.031 4.781,1.833 true 5.688,2.042 6.177,1.833 true 5.698,3.375 6.115,2.906 true 4.76,3.375 5,2.74 true 2.385,3.344 2.094,2.708 true 1.448,3.375 0.938,2.896 true 0.563,4.198 1.448,4.438 true 1.979,5.333 2.375,4.427 true 5.167,5.406 4.76,4.438 true 5.698,4.448 6.51,4.229 true 3.208,4.146 3.594,4.958 3.594,4.958 3.938,4.125 true 3.208,5.573 3.552,6.146 3.552,6.146 3.938,5.573 true 0.74,0.51 0.979,0.688 0.24,0.177 10 false *1 5.125,0.927 5.396,1.146 0.271,0.219 10 false *2 3.51,4.969 3.76,5.188 0.25,0.219 10 false *3 3.479,6.156 3.771,6.406 0.292,0.25 10 false *4 1.167,0.26 1.385,0.448 0.219,0.188 10 false *a 1.385,6.438 1.625,6.719 0.24,0.281 10 false *b 2.313,6.438 2.542,6.656 0.229,0.219 10 false *c 4.667,6.427 4.917,6.625 0.25,0.198 10 false *d 5.625,6.427 5.885,6.656 0.26,0.229 10 false *e 1.406,2.573 1.667,2.813 0.26,0.24 10 false (1) 2.771,2.552 3.052,2.771 0.281,0.219 10 false (2) 4.25,2.563 4.51,2.76 0.26,0.198 10 false (3) 5.635,2.563 5.885,2.792 0.25,0.229 10 false (4) 1.365,3.896 1.677,4.115 0.313,0.219 10 false (5) 2.313,3.896 2.604,4.094 0.292,0.198 10 false (6) 4.698,3.906 4.969,4.104 0.271,0.198 10 false (7) 5.656,3.896 5.948,4.104 0.292,0.208 10 false (8) 5.604,4.969 5.969,5.198 0.365,0.229 10 false (12) 4.688,4.969 5.01,5.188 0.323,0.219 10 false (11) 2.281,4.979 2.615,5.177 0.333,0.198 10 false (10) 1.417,4.979 1.677,5.219 0.26,0.24 10 false (9) 2.063,1.74 2.323,1.99 0.26,0.25 10 false (B) 4.813,1.719 5.063,1.969 0.25,0.25 10 false (C) 0.823,1.76 1.083,2 0.26,0.24 10 false (A) 6.208,1.719 6.479,1.99 0.271,0.271 10 false (D) 6.125,2.729 6.385,2.969 0.26,0.24 10 false (H) 4.917,2.573 5.177,2.813 0.26,0.24 10 false (G) 2.01,2.531 2.292,2.75 0.281,0.219 10 false (F) 0.406,4.073 0.615,4.313 0.208,0.24 10 false (I) 1.885,5.344 2.281,5.563 0.396,0.219 10 false (J) 5.115,5.417 5.396,5.656 0.281,0.24 10 false (K) 6.552,4.125 6.833,4.375 0.281,0.25 10 false (L) 5.802,0.26 6.021,0.448 0.219,0.188 10 false *a 0.823,2.719 1.135,2.938 0.313,0.219 10 false (E)
*1 Brake Actuator *2 Master Cylinder Pressure Sensor
*3 Pump *4 Reservoir
*a From Master Cylinder *b Rear Left
*c Rear Right *d Front Left
*e Front Right - -


Brake Actuator Operation in A-TRAC (When wheelspin of the front left wheel and rear right wheel occurs)
Item A-TRAC Operation
Not Activated Pressure Increase Mode Pressure Holding Mode Pressure Reduction Mode
Pump Off On ← ←
Master Cylinder Cut Solenoid Valve (1) Port (A) Off (Open) On (Closed) ← Off (Open)
(4) Port (D) Off (Open) On (Closed) ← Off (Open)
Reservoir Cut Solenoid Valve (2) Port (B) Off (Closed) On (Open) ← Off (Closed)
(3) Port (C) Off (Closed) On (Open) ← Off (Closed)
Front Brake Pressure Holding Solenoid Valve (7) Port (G) Off (Open) ← On (Closed) Off (Open)
(8) Port (H) Off (Open) On (Closed) ← ←
Pressure Reduction Solenoid Valve (11) Port (K) Off (Closed) ← ← ←
(12) Port (L) Off (Closed) ← ← ←
Rear Brake Pressure Holding Solenoid Valve (5) Port (E) Off (Open) On (Closed) ← ←
(6) Port (F) Off (Open) ← On (Closed) Off (Open)
Pressure Reduction Solenoid Valve (9) Port (I) Off (Closed) ← ← ←
(10) Port (J) Off (Closed) ← ← ←



f.

Auto LSD Operation

i.

The Auto LSD is a function that has effects similar to a mechanical type LSD (Limited Slip Differential). The Auto LSD employs the TRAC to control brake hydraulic pressure.


ii.

The skid control ECU detects slippage that occurs as a result of a rotational speed difference between the wheel with grip and the wheel without grip. Via the TRAC, the Auto LSD detects the wheel slip that occurs (the wheel that is rotating faster), based on the rotational difference of the right and left drive wheels, and creates the Auto LSD effect.


iii.

The following conditions must be met to enable operation of Auto LSD. The AUTO LSD indicator light turns on when the operation is enabled.

Operating Condition Content
2WD mode is selected The Auto LSD is operational only in the 2WD mode.
TRAC OFF mode or Auto LSD mode is selected By operating the VSC OFF switch, the vehicle is in the TRAC OFF mode or Auto LSD mode.
Accelerator pedal is on The Auto LSD does not operate when the brake pedal is being operated. This ensures that the Auto LSD does not interfere with the driver's attempt to reduce vehicle speed.
Vehicle speed is less than 50 km/h (31 mph) The vehicle is driving at less than 50 km/h (31 mph).

NOTICE:
·

Operate the Auto LSD control only when the wheels are susceptible to spinning, such as when driving on a grooved, slippery, or rough surface.

·

Make sure the vehicle is stopped before turning on the Auto LSD.

·

To prevent instability, do not continue driving the vehicle with the Auto LSD turned on.

·

The slip indicator light will blink when the Auto LSD is operating.

·

If the brake control of the Auto LSD is operated continuously, the temperature of the brake pads will rise. The skid control ECU, which monitors the temperature of the brake pads, alerts the driver by sounding the buzzer if the brake pads becomes overheated. In this case, the Auto LSD will temporarily stop operating in order to protect the system.

·

The Auto LSD applies the brakes to the drive wheel with the higher speed and controls the extent of the brake application in order to achieve the function of an LSD. However, it might not be able to achieve this function on a steep incline or on an extremely slippery surface, such as a frozen or snowy surface.




iv.

The auto LSD operation diagram shows the hydraulic circuit in the pressure increase mode when the auto LSD is activated.

Auto LSD Operation (When wheelspin of the rear right wheel occurs)
X131068C01
0.969,1.833 1.458,2.042 true 2.354,1.885 2.833,2.052 true 4.333,2.063 4.781,1.875 true 5.708,2.063 6.135,1.844 true 5.708,3.385 6.125,2.938 true 4.771,3.406 5.01,2.781 true 2.396,3.396 2.167,2.76 true 1.458,3.385 1.042,2.927 true 0.583,4.208 1.458,4.469 true 1.896,5.396 2.396,4.458 true 5.115,5.396 4.76,4.469 true 5.708,4.479 6.531,4.292 true 3.219,4.167 3.573,4.854 3.573,4.854 3.948,4.167 true 3.177,5.594 3.573,6.115 3.573,6.115 3.969,5.615 true 0.729,0.542 0.979,0.75 0.25,0.208 10 false *1 5.146,0.938 5.406,1.167 0.26,0.229 10 false *2 3.5,4.865 3.698,5.063 0.198,0.198 10 false *3 3.49,6.125 3.75,6.385 0.26,0.26 10 false *4 1.188,0.188 1.417,0.417 0.229,0.229 10 false *a 1.385,6.458 1.604,6.677 0.219,0.219 10 false *b 2.333,6.448 2.563,6.698 0.229,0.25 10 false *c 4.688,6.469 4.927,6.698 0.24,0.229 10 false *d 5.635,6.458 5.865,6.698 0.229,0.24 10 false *e 1.375,2.594 1.635,2.833 0.26,0.24 10 false (1) 2.771,2.594 3.031,2.833 0.26,0.24 10 false (2) 4.281,2.594 4.542,2.833 0.26,0.24 10 false (3) 5.688,2.604 5.948,2.844 0.26,0.24 10 false (4) 0.76,1.698 1.021,1.979 0.26,0.281 10 false (A) 2.135,1.75 2.396,2.031 0.26,0.281 10 false (B) 4.823,1.76 5.094,2 0.271,0.24 10 false (C) 6.177,1.729 6.427,2.01 0.25,0.281 10 false (D) 6.052,2.771 6.313,2.99 0.26,0.219 10 false (H) 4.927,2.615 5.188,2.844 0.26,0.229 10 false (G) 2.083,2.604 2.344,2.833 0.26,0.229 10 false (F) 0.885,2.75 1.146,2.99 0.26,0.24 10 false (E) 0.427,4.094 0.635,4.354 0.208,0.26 10 false (I) 1.823,5.406 2.094,5.635 0.271,0.229 10 false (J) 5.052,5.406 5.323,5.625 0.271,0.219 10 false (K) 6.573,4.188 6.833,4.406 0.26,0.219 10 false (L) 5.677,3.917 5.958,4.135 0.281,0.219 10 false (8) 4.719,3.917 4.99,4.125 0.271,0.208 10 false (7) 2.344,3.917 2.635,4.125 0.292,0.208 10 false (6) 1.375,3.917 1.604,4.115 0.229,0.198 10 false (5) 1.375,4.99 1.635,5.229 0.26,0.24 10 false (9) 2.281,4.99 2.594,5.198 0.313,0.208 10 false (10) 4.656,4.99 4.958,5.208 0.302,0.219 10 false (11) 5.604,5 5.948,5.219 0.344,0.219 10 false (12) 5.813,0.208 6.042,0.438 0.229,0.229 10 false *a
*1 Brake Actuator *2 Master Cylinder Pressure Sensor
*3 Pump *4 Reservoir
*a From Master Cylinder *b Rear Left
*c Rear Right *d Front Left
*e Front Right - -


Brake Actuator Operation in Auto LSD (When wheelspin of the rear right wheel occurs)
Item Auto LSD Operation
Not Activated Pressure Increase Mode Pressure Holding Mode Pressure Reduction Mode
Pump Off On ← ←
Master Cylinder Cut Solenoid Valve (1) Port (A) Off (Open) On (Closed) ← Off (Open)
(4) Port (D) Off (Open) ← ← ←
Reservoir Cut Solenoid Valve (2) Port (B) Off (Closed) On (Open) ← Off (Closed)
(3) Port (C) Off (Closed) ← ← ←
Front Brake Pressure Holding Solenoid Valve (7) Port (G) Off (Open) ← ← ←
(8) Port (H) Off (Open) ← ← ←
Pressure Reduction Solenoid Valve (11) Port (K) Off (Closed) ← ← ←
(12) Port (L) Off (Closed) ← ← ←
Rear Brake Pressure Holding Solenoid Valve (5) Port (E) Off (Open) On (Closed) ← ←
(6) Port (F) Off (Open) ← On (Closed) Off (Open)
Pressure Reduction Solenoid Valve (9) Port (I) Off (Closed) ← ← ←
(10) Port (J) Off (Closed) ← ← ←



g.

VSC Operation

i.

Based on the information provided by various sensors, switches, and the ECM, the skid control ECU determines the vehicle's yaw moment. Then, the skid control ECU controls the fluid pressure that is generated by the pump and pump motor and applies it by way of the solenoid valves to the brake wheel cylinder of each wheel in the following three modes: pressure reduction, pressure hold, and pressure increase modes. As a result, the tendency of the vehicle to experience a front wheel skid or rear wheel skid is restrained.


ii.

At this time, the skid control ECU outputs a VSC operation signal to the ECM and the combination meter and causes the buzzer to sound. Upon receiving this signal, the ECM controls the throttle to regulate the engine output. The slip indicator light will blink in the combination meter.


iii.

Front Wheel Skid Restraining (Turning to the Right)

·

In front wheel skid restraining control, the brakes of the rear wheel of the inner side of the turn is applied. Also, depending on whether the brake is on or off and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if those wheels are targeted for braking.

·

The diagram below shows the hydraulic circuit in the pressure increase mode, as it controls the front wheel skid condition while the vehicle makes a right turn.

·

In other operating modes, the pressure holding valves and the pressure reduction valves are turned on/off according to a pattern that suits the ABS and EBD operation.


VSC Operation (Front Wheel Skid Restraining)
X131068C01
0.969,1.833 1.458,2.042 true 2.354,1.885 2.833,2.052 true 4.333,2.063 4.781,1.875 true 5.708,2.063 6.135,1.844 true 5.708,3.385 6.125,2.938 true 4.771,3.406 5.01,2.781 true 2.396,3.396 2.167,2.76 true 1.458,3.385 1.042,2.927 true 0.583,4.208 1.458,4.469 true 1.896,5.396 2.396,4.458 true 5.115,5.396 4.76,4.469 true 5.708,4.479 6.531,4.292 true 3.219,4.167 3.573,4.854 3.573,4.854 3.948,4.167 true 3.177,5.594 3.573,6.115 3.573,6.115 3.969,5.615 true 0.729,0.542 0.979,0.75 0.25,0.208 10 false *1 5.146,0.938 5.406,1.167 0.26,0.229 10 false *2 3.5,4.865 3.698,5.063 0.198,0.198 10 false *3 3.49,6.125 3.75,6.385 0.26,0.26 10 false *4 1.188,0.188 1.417,0.417 0.229,0.229 10 false *a 1.385,6.458 1.604,6.677 0.219,0.219 10 false *b 2.333,6.448 2.563,6.698 0.229,0.25 10 false *c 4.688,6.469 4.927,6.698 0.24,0.229 10 false *d 5.635,6.458 5.865,6.698 0.229,0.24 10 false *e 1.375,2.594 1.635,2.833 0.26,0.24 10 false (1) 2.771,2.594 3.031,2.833 0.26,0.24 10 false (2) 4.281,2.594 4.542,2.833 0.26,0.24 10 false (3) 5.688,2.604 5.948,2.844 0.26,0.24 10 false (4) 0.76,1.698 1.021,1.979 0.26,0.281 10 false (A) 2.135,1.75 2.396,2.031 0.26,0.281 10 false (B) 4.823,1.76 5.094,2 0.271,0.24 10 false (C) 6.177,1.729 6.427,2.01 0.25,0.281 10 false (D) 6.052,2.771 6.313,2.99 0.26,0.219 10 false (H) 4.927,2.615 5.188,2.844 0.26,0.229 10 false (G) 2.083,2.604 2.344,2.833 0.26,0.229 10 false (F) 0.885,2.75 1.146,2.99 0.26,0.24 10 false (E) 0.427,4.094 0.635,4.354 0.208,0.26 10 false (I) 1.823,5.406 2.094,5.635 0.271,0.229 10 false (J) 5.052,5.406 5.323,5.625 0.271,0.219 10 false (K) 6.573,4.188 6.833,4.406 0.26,0.219 10 false (L) 5.677,3.917 5.958,4.135 0.281,0.219 10 false (8) 4.719,3.917 4.99,4.125 0.271,0.208 10 false (7) 2.344,3.917 2.635,4.125 0.292,0.208 10 false (6) 1.375,3.917 1.604,4.115 0.229,0.198 10 false (5) 1.375,4.99 1.635,5.229 0.26,0.24 10 false (9) 2.281,4.99 2.594,5.198 0.313,0.208 10 false (10) 4.656,4.99 4.958,5.208 0.302,0.219 10 false (11) 5.604,5 5.948,5.219 0.344,0.219 10 false (12) 5.813,0.208 6.042,0.438 0.229,0.229 10 false *a
*1 Brake Actuator *2 Master Cylinder Pressure Sensor
*3 Pump *4 Reservoir
*a From Master Cylinder *b Rear Left
*c Rear Right *d Front Left
*e Front Right - -


Brake Actuator Operation in VSC (Front Wheel Skid Restraining)
Item VSC Operation
Not Activated Pressure Increase Mode Pressure Holding Mode Pressure Reduction Mode
Pump Off On ← ←
Master Cylinder Cut Solenoid Valve (1) Port (A) Off (Open) On (Closed) ← Off (Open)
(4) Port (D) Off (Open) ← ← ←
Reservoir Cut Solenoid Valve (2) Port (B) Off (Closed) On (Open) ← Off (Closed)
(3) Port (C) Off (Closed) ← ← ←
Front Brake Pressure Holding Solenoid Valve (7) Port (G) Off (Open) ← ← ←
(8) Port (H) Off (Open) ← ← ←
Pressure Reduction Solenoid Valve (11) Port (K) Off (Closed) ← ← ←
(12) Port (L) Off (Closed) ← ← ←
Rear Brake Pressure Holding Solenoid Valve (5) Port (E) Off (Open) On (Closed) ← ←
(6) Port (F) Off (Open) ← On (Closed) Off (Open)
Pressure Reduction Solenoid Valve (9) Port (I) Off (Closed) ← ← ←
(10) Port (J) Off (Closed) ← ← ←


iv.

Rear Wheel Skid Restraining (Turning to the Right)

·

In rear wheel skid restraining control, the brake of the front wheel of the outer side of the turn is applied. Also, depending on whether the brake is on or off and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if those wheels are targeted for braking.

·

The diagram below shows the hydraulic circuit in the pressure increase mode, as it controls the rear wheel skid condition while the vehicle makes a right turn.

·

In other operating modes, the pressure holding valve and the pressure reduction valve are turned on/off according to the ABS and EBD operation pattern.


VSC Operation (Rear Wheel Skid Restraining)
X131069C01
1,1.813 1.458,2.031 true 2.24,1.823 2.833,2.031 true 4.333,2.031 4.781,1.823 true 5.698,2.031 6.125,1.875 true 4.771,3.354 4.948,2.729 true 5.698,3.375 6.198,2.927 true 2.396,3.354 2.229,2.698 true 1.448,3.365 1.083,2.906 true 0.604,4.167 1.458,4.438 true 2,5.323 2.396,4.438 true 5.292,5.375 4.771,4.448 true 5.708,4.448 6.521,4.188 true 3.208,4.146 3.583,4.99 3.583,4.99 3.948,4.146 true 3.219,5.573 3.583,6.104 3.583,6.104 3.958,5.573 true 0.771,0.458 1.021,0.677 0.25,0.219 10 false *1 5.177,0.896 5.396,1.125 0.219,0.229 10 false *2 3.51,5 3.76,5.25 0.25,0.25 10 false *3 3.5,6.115 3.75,6.396 0.25,0.281 10 false *4 1.198,0.208 1.479,0.417 0.281,0.208 10 false *a 1.406,6.448 1.667,6.677 0.26,0.229 10 false *b 2.333,6.458 2.583,6.677 0.25,0.219 10 false *c 4.698,6.438 4.938,6.677 0.24,0.24 10 false *d 5.646,6.438 5.854,6.677 0.208,0.24 10 false *e 1.438,2.563 1.729,2.823 0.292,0.26 10 false (1) 5.802,0.219 6.083,0.427 0.281,0.208 10 false *a 2.781,2.563 3.073,2.823 0.292,0.26 10 false (2) 4.292,2.552 4.583,2.813 0.292,0.26 10 false (3) 5.729,2.573 6.021,2.833 0.292,0.26 10 false (4) 5.667,3.885 5.969,4.104 0.302,0.219 10 false (8) 4.698,3.896 4.99,4.115 0.292,0.219 10 false (7) 2.333,3.896 2.625,4.125 0.292,0.229 10 false (6) 1.406,3.896 1.698,4.104 0.292,0.208 10 false (5) 1.375,4.969 1.646,5.219 0.271,0.25 10 false (9) 2.26,4.958 2.594,5.177 0.333,0.219 10 false (10) 5.615,4.969 5.948,5.188 0.333,0.219 10 false (12) 0.792,1.656 1.083,1.938 0.292,0.281 10 false (A) 2.031,1.667 2.281,1.938 0.25,0.271 10 false (B) 4.813,1.688 5.104,1.948 0.292,0.26 10 false (C) 6.167,1.75 6.406,2.01 0.24,0.26 10 false (D) 6.156,2.719 6.469,2.969 0.313,0.25 10 false (H) 4.875,2.552 5.167,2.792 0.292,0.24 10 false (G) 2.135,2.5 2.427,2.76 0.292,0.26 10 false (F) 0.979,2.719 1.271,2.917 0.292,0.198 10 false (E) 0.438,4 0.688,4.26 0.25,0.26 10 false (I) 1.927,5.313 2.219,5.573 0.292,0.26 10 false (J) 5.229,5.375 5.521,5.625 0.292,0.25 10 false (K) 4.719,4.958 5.01,5.177 0.292,0.219 10 false (11) 6.563,4.073 6.844,4.292 0.281,0.219 10 false (L)
*1 Brake Actuator *2 Master Cylinder Pressure Sensor
*3 Pump *4 Reservoir
*a From Master Cylinder *b Rear Left
*c Rear Right *d Front Left
*e Front Right - -


Brake Actuator Operation in VSC (Rear Wheel Skid Restraining)
Item VSC Operation
Not Activated Pressure Increase Mode Pressure Holding Mode Pressure Reduction Mode
Pump Off On ← ←
Master Cylinder Cut Solenoid Valve (1) Port (A) Off (Open) ← ← ←
(4) Port (D) Off (Open) On (Closed) ← Off (Open)
Reservoir Cut Solenoid Valve (2) Port (B) Off (Closed) ← ← ←
(3) Port (C) Off (Closed) On (Open) ← Off (Closed)
Front Brake Pressure Holding Solenoid Valve (7) Port (G) Off (Open) ← On (Closed) Off (Open)
(8) Port (H) Off (Open) On (Closed) ← ←
Pressure Reduction Solenoid Valve (11) Port (K) Off (Closed) ← ← ←
(12) Port (L) Off (Closed) ← ← ←
Rear Brake Pressure Holding Solenoid Valve (5) Port (E) Off (Open) ← ← ←
(6) Port (F) Off (Open) ← ← ←
Pressure Reduction Solenoid Valve (9) Port (I) Off (Closed) ← ← ←
(10) Port (J) Off (Closed) ← ← ←



h.

Trailer Sway Control Operation

i.

The operation of the solenoid valves under the trailer sway control is the same as the VSC operation.



i.

Engine Output Control

i.

During a VSC operation, the skid control ECU outputs an engine output control request signal to the ECM. Upon receiving this signal, the ECM effects throttle control to regulate the engine output.

X128289E01
5.448,0.031 7.156,0.302 1.708,0.271 9 false (a): Start of engine control 5.448,0.583 7.125,0.833 1.677,0.25 9 false (c): Brake control completed 5.448,0.302 7.135,0.563 1.688,0.26 9 false (b): Start of brake control 5.448,0.865 7.146,1.156 1.698,0.292 9 false (d): Engine control completed 0.063,1.052 1.406,2.302 1.344,1.25 9 false Vehicle Condition (Front Wheel Skid or Rear Wheel Skid Level) 0.063,2.708 1.104,3.094 1.042,0.385 9 false Engine Torque 0.052,4.052 1.365,4.854 1.313,0.802 9 false Brake Wheel Cylinder Fluid Pressure* 1.406,4.865 1.729,5.177 0.323,0.313 9 false Low 1.417,3.427 1.719,3.76 0.302,0.333 9 false Low 1.417,1.948 1.719,2.281 0.302,0.333 9 false Low 1.406,0.792 1.74,1.125 0.333,0.333 9 false High 1.396,2.292 1.698,2.625 0.302,0.333 9 false High 1.406,3.75 1.729,4.094 0.323,0.344 9 false High 5.24,5.021 5.646,5.417 0.406,0.396 9 false Time 5.229,3.583 5.635,3.979 0.406,0.396 9 false Time 5.146,2.104 5.552,2.5 0.406,0.396 9 false Time 0.167,5.417 4.969,5.771 4.802,0.354 9 false *: The wheel cylinder that activates varies depending on the condition of the vehicle. 2.229,0.635 2.448,0.844 0.219,0.208 9 false (a) 2.5,0.646 2.719,0.854 0.219,0.208 9 false (b) 4.188,0.646 4.406,0.854 0.219,0.208 9 false (c) 4.458,0.646 4.677,0.854 0.219,0.208 9 false (d)



j.

Initial Check

i.

Each time the ignition switch is turned on, and the vehicle reaches approximately speed of 23 km/h (14.3 mph) or more, the skid control ECU performs an initial check.


ii.

The functions of each solenoid valve and pump motor in the brake actuator are checked in sequence.




Self-Diagnosis


a.

If the skid control ECU detects a malfunction in the brake control system, the warning lights or indicator light illuminate. At the same time, a Diagnostic Trouble Code (DTC) is stored in the memory of the skid control ECU.


b.

This system has a sensor signal check (test mode) function.


c.

For details of DTCs and check function, refer to the Repair Manual.



Fail-Safe


a.

If a failure occurs in the skid control ECU, sensors or brake actuator assembly, the system continues effecting brake control by excluding the failed area and using only the areas that are operating normally.