Home › General › BODY ELECTRICAL › SRS AIRBAG SYSTEM
NM27L0U _V1 General _050243 BODY ELECTRICAL _0245175 SRS AIRBAG SYSTEM UN GENERAL/CONTROL/DETAILS F

BODY ELECTRICAL  SRS AIRBAG SYSTEM  GENERAL/CONTROL/DETAILS  AIRBAG FOR FRONTAL COLLISION  


General


a.

The airbag for frontal collisions is composed of the driver and front passenger dual-stage SRS airbags and the driver and front passenger SRS knee airbags. These airbags deploy simultaneously.

i.

The center airbag sensor assembly detects the information indicated below from various sources in order to activate the dual-stage control:

Information for Dual-stage Control
Airbag Information Source
Driver Extent of Impact
·

Front Airbag Sensor RH or LH

·

Center Airbag Sensor Assembly


Driver Seat Position Seat Position Sensor
Seat Belt Condition Seat Belt Buckle Switch (Non-contact Type)
Front Passenger Extent of Impact
·

Front Airbag Sensor RH or LH

·

Center Airbag Sensor Assembly


Occupant Classification Occupant Classification Sensors (4) (Through Occupant Classification ECU)
Seat Belt Condition Seat Belt Buckle Switch (Non-contact Type) (Through Occupant Classification ECU)




System Diagram


Y196248E01
0.99,1.417 1.719,1.771 0.729,0.354 10 false Collision 2.042,1.406 2.604,1.781 0.563,0.375 10 false Impact 3.417,0.313 4.729,1 1.313,0.688 10 false Front Airbag Sensor RH or LH 5.5,1.813 6.688,2.594 1.188,0.781 10 false Seat Belt Pretensioner LH 5.552,2.708 6.646,3.396 1.094,0.688 10 false Driver SRS Knee Airbag 0.385,2.563 1.521,3.323 1.135,0.76 10 false Seat Belt Buckle Switch LH 0.396,3.646 1.896,4.031 1.5,0.385 10 false Seat Position Sensor 0.385,4.406 1.865,5.146 1.479,0.74 10 false Occupant Classification Sensor (4) 0.375,5.469 1.885,6.156 1.51,0.688 10 false Seat Belt Buckle Switch RH 0.385,7.302 1.844,7.646 1.458,0.344 10 false - SRS Warning Light 0.99,8.031 1.719,8.385 0.729,0.354 10 false ECM 2.302,4.833 3.167,6 0.865,1.167 10 false Occupant Classification ECU 5.521,3.604 6.948,4.396 1.427,0.792 10 false Driver Dual-stage SRS Airbag 5.563,4.938 6.698,6.031 1.135,1.094 10 false Front Passenger Dual-stage SRS Airbag 5.563,6.167 6.979,6.969 1.417,0.802 10 false Front Passenger SRS Knee Airbag 5.531,7.083 6.646,7.99 1.115,0.906 10 false Seat Belt Pretensioner RH 3.656,3.938 4.563,5.281 0.906,1.344 10 false Center Airbag Sensor Assembly 1.594,7.667 2.677,7.99 1.083,0.323 10 false Fuel Cut Signal 2.156,6.427 3.417,7.146 1.26,0.719 10 false Airbag Deployment Signal 2.135,8.313 3.115,8.688 0.979,0.375 10 false CAN (V1 Bus) 0.375,6.896 1.781,7.271 1.406,0.375 10 false Combination Meter


SRS Driver and Front Passenger Airbags


a.

The SRS driver and front passenger airbags each contain a set of 2 initiators and propellants. The center airbag sensor assembly helps optimize the airbag inflation output by controlling the inflation timing of these initiators.



SRS Knee Airbags


a.

The SRS knee airbags deploy simultaneously with the front airbags in a frontal collision. With the deployment of the SRS knee airbags, the driver's and front passenger's lower bodies are restricted, thus enhancing the excellent passenger protection provided by the seat belt and front airbags.


b.

The SRS knee airbag consists of an airbag door, an inflator, and a bag.

Y196249C01
2.177,2.073 2.51,1.375 true 5.052,2.188 4.729,1.375 true 3.677,3.479 3.031,2.854 true 2.365,4.219 2.885,3.865 true 4.281,3.854 4.906,4.25 true 2.052,2.073 2.333,2.323 0.281,0.25 10 false *1 5.01,2.188 5.25,2.406 0.24,0.219 10 false *2 2.875,2.688 3.104,2.958 0.229,0.271 10 false *3 2.219,4.198 2.469,4.448 0.25,0.25 10 false *4 4.948,4.219 5.208,4.469 0.26,0.25 10 false *5
*1 Driver SRS Knee Airbag *2 Front Passenger SRS Knee Airbag
*3 Bag *4 Inflator
*5 Airbag Door - -




Front Airbag Sensor


a.

The front airbag sensor uses an electrical type deceleration sensor. Based on the deceleration of the vehicle during a front collision, a distortion is created in the sensor and converted into an electrical signal. Accordingly, the extent of the initial collision can be detected in detail.



Seat Belt Buckle Switch


a.

The seat belt buckle switch determines that the seat belt is fastened.

i.

A contact type switch and a non-contact type switch are built into the seat belt buckle on the driver side. The contact type switch is for the seat belt reminder system and the non-contact type switch is for the SRS airbag system.


ii.

A non-contact type switch is built into the seat belt buckle on the front passenger side.


iii.

The non-contact type switch contains a Hall IC and 2 magnets, installed into the front seat inner belt assembly.

Electrical Circuit
Y182586C01
1.948,1.281 2.26,1.438 0.313,0.156 10 false *1 2.365,2.542 2.698,2.74 0.333,0.198 10 false *a 5.031,2.542 5.385,2.75 0.354,0.208 10 false *b 1.771,0.219 2.083,0.438 0.313,0.219 10 false *c 2.646,0.229 2.958,0.438 0.313,0.208 10 false *d 1.771,2.25 2.083,2.49 0.313,0.24 10 false *e 4.885,0.229 5.198,0.417 0.313,0.188 10 false *f 4.875,2.24 5.198,2.458 0.323,0.219 10 false *g 5.042,1.271 5.354,1.427 0.313,0.156 10 false *1
*1 Hall IC - -
*a Driver *b Front Passenger
*c From Center Airbag Sensor Assembly *d From Main Body ECU (Driver Side Junction Block)
*e To Center Airbag Sensor Assembly *f From Occupant Classification ECU
*g To Occupant Classification ECU - -



iv.

The ejector inside the front seat inner belt assembly and the plate installed to the ejector move when the seat belt is removed or inserted. The movement of the plate changes the magnetic flux density of the magnet.


v.

The Hall IC detects changes in the magnetic flux density. These changes indicate that the seat belt is either fastened or unfastened, and the Hall IC outputs a signal to the center airbag sensor assembly (for driver) or occupant classification ECU (for front passenger).

Y182587C01
2.198,2.229 1.594,1.844 true 2.333,2.49 1.625,2.5 true 2.219,2.802 1.667,3.24 true 5.042,3.188 5.042,3.458 true 5.167,1.167 4.635,1.167 true 5.844,0.927 5.313,0.927 true 1.417,1.76 1.635,2.031 0.219,0.271 10 false *1 1.417,2.406 1.604,2.635 0.188,0.229 10 false *2 1.458,3.177 1.656,3.427 0.198,0.25 10 false *3 4.281,0.635 4.667,0.917 0.385,0.281 10 false *a 4.365,2.604 4.677,2.833 0.313,0.229 10 false *b 4.99,3.531 5.313,3.74 0.323,0.208 10 false *c 4.448,1.083 4.635,1.313 0.188,0.229 10 false *2 5.875,0.823 6.094,1.083 0.219,0.26 10 false *4 4.594,1.656 4.792,1.906 0.198,0.25 10 false *3
*1 Ejector *2 Hall IC
*3 Magnet *4 Plate
*a Seat belt not fastened *b Seat belt fastened
*c Magnetic Flux - -





Seat Position Sensor


a.

The seat position sensor detects the slide position of the driver seat. This sensor, which uses a Hall IC, detects changes in the magnetic flux that occur due to the movement of the upper rail.

Y182588C01
2.135,2.49 2.135,1.573 true 2.052,2.521 2.385,2.74 0.333,0.219 10 false *1 1.885,0.313 2.219,0.552 0.333,0.24 10 false *a 4.719,0.26 5.083,0.5 0.365,0.24 10 false *b
*1 Seat Position Sensor - -
*a Seat position is rearward *b Seat position is frontward


HINT:

Follow the procedure indicated below to install the seat position sensor.

1.

Insert a 1.0 mm (0.04 in.) feeler gauge between the seat position sensor and the lower rail portion.

2.

Tighten the mounting bolt to the specified torque with the seat position sensor pushed down as shown below.


For details, refer to the Repair Manual.

Y182589C03
1.729,0.896 2.219,0.896 true 1.563,1.854 2.229,1.854 true 4.948,0.833 5.438,0.833 true 4.698,1.854 5.365,1.854 true 2.271,0.813 2.615,1.073 0.344,0.26 10 false *1 2.313,1.75 2.635,2 0.323,0.25 10 false *2 1.479,2.469 1.813,2.688 0.333,0.219 10 false *a 4.667,2.469 5.042,2.698 0.375,0.229 10 false *b 2.26,1.313 3.417,1.604 1.156,0.292 10 false 1.0 mm (0.04 in.) 5.531,1.229 6.688,1.521 1.156,0.292 10 false 1.0 mm (0.04 in.) 5.521,0.75 5.865,1.01 0.344,0.26 10 false *1 5.427,1.771 5.75,2.021 0.323,0.25 10 false *2
*1 Seat Position Sensor *2 Lower Rail
*a For Manual Seat *b For Power Seat