Home › General › BODY ELECTRICAL › DYNAMIC LASER CRUISE CONTROL SYSTEM
NM27L0U _V1 General _050243 BODY ELECTRICAL _0249483 DYNAMIC LASER CRUISE CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

BODY ELECTRICAL  DYNAMIC LASER CRUISE CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  SYSTEM CONTROL  


GENERAL


a.

The control of the dynamic laser cruise control system varies depending on the mode:

Control Outline Mode
A B

A: Constant Speed Control Mode

B: Vehicle-to-vehicle Distance Control Mode.

*: 3UR-FE Engine Model

Constant Speed Control The ECM compares the actual vehicle speed and the set speed and if the vehicle speed is higher than the set speed, it uses the throttle control motor to decrease the throttle opening. If the actual vehicle speed is lower than the set speed, it uses the throttle control motor to increase the throttle opening. ○ ○
Deceleration Control Effects throttle control and brake control in order to decelerate the vehicle so that the vehicle-to-vehicle distance between the driver's own vehicle and the vehicle ahead equals the set distance. - ○
Follow-up Control After effecting deceleration control, the vehicle follows the vehicle ahead in order to maintain the proper vehicle-to-vehicle distance in accordance with the vehicle speed. - ○
Acceleration Control Accelerates the vehicle in order to attain the set speed if the vehicle ahead or the driver's own vehicle has changed lanes. - ○
Set Control While this system fulfils the following conditions, and the cruise control switch is pressed to the SET/- side and released when the main switch on the cruise control switch has been pressed to turn the system ON, the ECM stores the vehicle speed and maintains the vehicle constantly at that speed.
·

The shift lever is in D position

·

The shift lever is shifted in the S mode, and shift range is 4th, 5th or 6th*.


○ ○
The vehicle is running within the following range:
·

U.S.A.: About 27 to 125 mph

·

Canada: About 45 to 200 km/h


○ -
The vehicle is running within the following range:
·

U.S.A.: About 27 to 85 mph

·

Canada: About 45 to 135 km/h


- ○
Low Speed Limit Control The low speed limit is the lowest speed that cruise control can be set at and it is designed to be approx. "40 km/h (25 mph)". The cruise control cannot be set below that speed. If the vehicle speed drops below that speed while running in the cruise control, the cruise control will be cancelled automatically. However, the set speed in the memory is kept. ○ ○
Coast Control While the cruise control switch is held to the SET/- side, the vehicle speed and the vehicle setting speed changes as follows, according to the mode: ○ ○
·

The vehicle decelerates constantly.

·

The set speed changes to the speed at which the switch was turned OFF.


○ -
·

The set speed decreases in increments 5 km/h or 5 mph.[Example: 103 → 100 → 95 km/h, 62 → 60 → 55 mph]

·

The vehicle decelerates rapidly due to ETCS-i.


- ○
Tap-down Control When the cruise control switch is pushed momentarily (approx. 0.6 sec) to the SET/- side, the vehicle speed and the set speed change as follows, according to the mode:
·

The vehicle will decelerate in increments of approximately 1.6 km/h (1 mph) for each time the switch was pressed.

·

However, if the difference between the actual vehicle speed and the set speed is greater than 5 km/h (3 mph), the set speed will change to the speed at which the vehicle was being driven at the time the switch was operated.


○ -
Accelerator Control When the cruise control switch is pushed to the RES/+ side and held, the vehicle speed and the vehicle setting speed change as follows, according to the mode: ○ ○
·

The vehicle will accelerate constantly.

·

The set speed changes to the speed at which the switch was turned OFF.


○ -
·

The set speed increases in increments 5 km/h or 5 mph.[Example: 93 → 95 → 100 km/h, 52 → 55 → 60 mph]

·

The vehicle will accelerate to the speed that is set at the time the switch is released.


However, only the set speed will change during follow-up control.
- ○
Resume Control When the driver pushes the cruise control switch to the RES/+ side after the vehicle speed has exceeded the low speed limit, the cruise control resumes operation to reach the vehicle speed that was set at the time the driver canceled cruise control. ○ ○
Even if the vehicle speed drops below the low speed limit, resume can be performed when the vehicle speed exceeds the low speed limit. ○ ○
If the vehicle ahead changes driving lanes during follow-up control, the vehicle speed is gradually increased to the set speed. At this time, the vehicle speed can be increased promptly by pushing the cruise control switch to the RES/+ side. - ○
Tap-up Control When the cruise control switch is pushed momentarily (approx. 0.6 sec.) to the RES/+ side, the vehicle speed and the set speed change as follows
·

The vehicle will accelerate in increments of approx. 1.6 km/h (1 mph) for each time the switch was pressed.

·

However, if the difference between the actual vehicle speed and the set speed is greater than 5 km/h (3 mph), the set speed changes to the speed as which the vehicle was being driven at the time the switch was operated.


○ -
Shift Down Control When the vehicle is cruising uphill, shift-down control may be performed by the ECT (Electronic Control Transmission). The ECM shifts up the gear when the ECM judges the end of cruising uphill based on the throttle valve angle. ○ ○
Manual Cancel Control If any of the following signals is sent to the ECM, the cruise control is cancelled accordingly.
·

A stop light switch ON signal (The brake pedal is depressed.)

·

A signal to indicate that the shift lever is moved from D to N

·

A signal to indicate that the 1st, 2nd or 3rd range is selected in the S mode position

·

A CANCEL switch ON signal (The cruise control switch is moved to the CANCEL side.)

·

A main switch OFF signal

·

A VSC operation signal


○ ○
Automatic Cancel Control When an automatic cancel signal is sent to the ECM, the cruise control operation is canceled. At this time, the warning and the control resumption condition vary according to the cancel signal. ○ ○
Mode Switching Control The following operations switch the modes:
1.

Main switch on the cruise control switch is ON. (Starts in the vehicle-to-vehicle distance control mode)

2.

Cruise control switch is held to the MODE side. (Approx. 1 second or more)


If the switch is pushed to any other side before switching modes, switch the cruise control system OFF; then, perform steps 1) and 2) again.
○ ○
Diagnosis If a malfunction occurs in the dynamic laser cruise control system during cruise control operation, the ECM cancels cruise control and diagnoses and memorizes the faults related to the malfunction. ○ ○



CONSTANT SPEED CONTROL


a.

General

i.

In the constant speed control mode, the constant speed control is effected by the ECM.


ii.

In the vehicle-to-vehicle distance control mode, the constant speed control is effected by the laser radar sensor and distance control ECU.



b.

Constant Speed Control in Vehicle-to-vehicle Distance Control Mode

i.

The laser radar sensor transmits the information about the vehicle ahead to the distance control ECU. The distance control ECU transmits a laser radar sensor operation signal to the ECM. The ECM compares the set speed and the actual vehicle speed, and effects constant speed control by regulating the throttle control in order to attain the set speed.

Y196175E01
2.031,2.417 3.219,2.917 1.188,0.5 10 false Own Vehicle 5.146,1.615 5.698,2.01 0.552,0.396 10 false ECM 5.375,1.125 6.531,1.469 1.156,0.344 10 false CAN (V1 Bus) 4.573,0.646 6.063,1.021 1.49,0.375 10 false Distance Control ECU 2.448,0.677 3.74,1.042 1.292,0.365 10 false Laser Radar Sensor 4.594,2.5 6.052,2.906 1.458,0.406 10 false Throttle Control Motor




DECELERATION CONTROL


a.

The distance control ECU calculates the target deceleration rate in accordance with signals from the laser radar sensor, and transmits a deceleration request signal to the ECM. Upon receiving this signal, the ECM closes the throttle valve in order to cause the vehicle to decelerate.


b.

This control is not effected in the presence of a parked vehicle or object, or below the settable vehicle speed range.

Y196176E01
5.125,1.438 5.823,1.813 0.698,0.375 10 false ECM 5.385,0.917 6.615,1.26 1.229,0.344 10 false CAN (V1 Bus) 4.552,0.438 6.052,0.813 1.5,0.375 10 false Distance Control ECU 2.448,0.458 3.771,0.833 1.323,0.375 10 false Laser Radar Sensor 2.042,0.969 3.083,1.396 1.042,0.427 10 false Vehicle Ahead 2.031,2.469 3.021,2.875 0.99,0.406 10 false Own Vehicle 4.552,2.281 6.021,2.635 1.469,0.354 10 false Throttle Control Motor


c.

If distance control ECU determines that further deceleration is necessary, it transmits a brake request signal to the ECM. Upon receiving this signal, the ECM transmits a brake request signal to skid control ECU. The skid control ECU then controls the brake actuator to apply the brakes.


d.

At this time, if the deceleration rate is higher than a predetermined value, the skid control ECU outputs a stop light illumination request signal to the stop light control relay, in order to inform anyone who might be following the vehicle.

Y196177E01
4.625,2.729 5.167,3.063 0.542,0.333 10 false ECM 4.25,1.896 5.438,2.313 1.188,0.417 10 false Skid Control ECU 3.771,1.083 5.229,1.521 1.458,0.438 10 false Distance Control ECU 1.979,1.073 3.25,1.458 1.271,0.385 10 false Laser Radar Sensor 4.021,3.583 5.479,3.938 1.458,0.354 10 false Throttle Control Motor 6.021,2.25 6.906,2.615 0.885,0.365 10 false Stop Light 5.792,1.688 6.875,2.052 1.083,0.365 10 false Brake Actuator 2.771,1.927 3.719,2.344 0.948,0.417 10 false CAN (V1 Bus) 1.063,1.635 2.104,2.052 1.042,0.417 10 false Vehicle Ahead 1.042,2.563 2.073,2.906 1.031,0.344 10 false Own Vehicle 1.052,3.531 2.229,3.885 1.177,0.354 10 false Vehicle Behind

i.

If further deceleration is necessary after the stop lights are illuminated, the skid control ECU sounds the VSC warning buzzer based on the request signal from the distance control ECU to urge the driver to depress the brake pedal.

Y196178E01
4.635,3.281 5.146,3.625 0.51,0.344 10 false ECM 4.24,2.208 5.417,2.677 1.177,0.469 10 false Skid Control ECU 3.74,1.135 5.26,1.531 1.521,0.396 10 false Distance Control ECU 1.99,1.104 3.302,1.49 1.313,0.385 10 false Laser Radar Sensor 2.771,2.052 3.729,2.49 0.958,0.438 10 false CAN (V1 Bus) 1,1.698 2.052,2.094 1.052,0.396 10 false Vehicle Ahead 1,2.625 2.042,2.958 1.042,0.333 10 false Own Vehicle 0.969,3.479 2.135,3.854 1.167,0.375 10 false Vehicle Behind 4.021,4.125 5.5,4.5 1.479,0.375 10 false Throttle Control Motor 5.719,2.792 7.083,3.177 1.365,0.385 10 false VSC Warning Buzzer 5.99,2.24 6.844,2.573 0.854,0.333 10 false Stop Light 5.833,1.677 6.896,2.01 1.063,0.333 10 false Brake Actuator




FOLLOW-UP CONTROL


a.

After effecting deceleration control, distance control ECU transmits a request signal to the ECM so that the vehicle can follow the vehicle ahead while maintaining the proper vehicle-to-vehicle distance according to the vehicle speed. Upon receiving this signal, the ECM regulates the throttle in order to effect follow-up control.


b.

Three stages (long, middle, and short) of vehicle-to-vehicle distance can be selected by operating the distance control switch.

Y196179E01
4.094,1.458 4.656,1.823 0.563,0.365 10 false ECM 3.479,0.375 5,0.771 1.521,0.396 10 false Distance Control ECU 1.406,0.49 2.75,0.875 1.344,0.385 10 false Laser Radar Sensor 0.26,0.646 1.292,1.021 1.031,0.375 10 false Vehicle Ahead 1.01,2.531 2.094,2.917 1.083,0.385 10 false Own Vehicle 3.49,2.24 4.958,2.594 1.469,0.354 10 false Throttle Control Motor 4.375,0.969 5.49,1.396 1.115,0.427 10 false CAN (V1 Bus) 5.51,0.365 7.073,0.792 1.563,0.427 10 false Distance Control Switch



ACCELERATION CONTROL


a.

If the distance control ECU detects (based on the laser radar sensor) that either the vehicle ahead or own vehicle has changed lanes, an acceleration request signal is transmitted to the ECM in order to attain the set speed. Upon receiving this signal, the ECM regulates the throttle in order to effect acceleration control.

Y196180E01
5.135,1.417 5.646,1.75 0.51,0.333 10 false ECM 5.375,0.927 6.427,1.302 1.052,0.375 10 false CAN (V1 Bus) 4.5,0.396 5.99,0.76 1.49,0.365 10 false Distance Control ECU 2.406,0.49 3.75,0.854 1.344,0.365 10 false Laser Radar Sensor 2.198,1.24 3.354,1.604 1.156,0.365 10 false Vehicle Ahead 1.823,2.49 2.833,2.885 1.01,0.396 10 false Own Vehicle 4.552,2.25 6.073,2.688 1.521,0.438 10 false Throttle Control Motor



AUTOMATIC CANCEL CONTROL


a.

If any of the conditions listed below occurs while the vehicle is in cruise control (A: constant speed control mode, B: vehicle-to-vehicle distance control mode), the cruise control will be canceled. Then, the following warning will be issued.

1.

Warning message is displayed on the multi-information display.

2.

Master warning light illuminates.

3.

Buzzer sounds.

4.

CRUISE main indicator light flashes.

Mode Description of Malfunction Warning
A and B If any of the conditions listed below occurs, the ECM clears the set speed and cancels the cruise control.
·

Malfunction of the vehicle speed signal.

·

Malfunction in the ETCS-i.

·

An open or short circuit in the stop light switch.


The cruise control is prohibited until the conditions are restored or the cruise control system is turned OFF and back ON again using the main switch on the cruise control switch.
1.

"CHECK CRUISE SYSTEM"

2.

Illuminate

3.

Sound Once

4.

Flash


If the condition listed below occurs, the ECM cancels the cruise control while retaining the set speed in its memory.
·

The vehicle speed drops below low speed limit [approx. 40 km/h (25 mph)].


1.

-

2.

-

3.

-

4.

-


A If the condition listed below occurs, the ECM cancels the cruise control.
·

The vehicle speed drops more than 16 km/h (10 mph) below the set speed.


1.

-

2.

-

3.

-

4.

-


B If any of the conditions listed below occur, the ECM clears the set speed and cancels the cruise control.
·

Malfunction of the laser radar sensor.

·

Displacement of the axis of the laser radar sensor.

·

Malfunction in the dynamic laser cruise control system other than those given above.


The cruise control is prohibited until the ignition switch is turned ON again.
1.

"CHECK CRUISE SYSTEM"

2.

Illuminate

3.

Sound Once

4.

Flash


If the condition listed below occurs, the ECM cancels the cruise control while retaining the set speed in its memory.
·

The laser radar sensor is dirty.


The cruise control is prohibited until the conditions are restored or the main switch on the cruise control switch is turned ON again.
1.

"CLEAN RADAR SENSOR"

2.

Illuminate

3.

Sound Once

4.

Flash


If any of the conditions listed below occur, the ECM cancels the cruise control while retaining the set vehicle speed in its memory.
·

The wipers operate at HI speed (including AUTO mode).

·

The measurement becomes extremely unstable due to poor weather conditions.


The cruise control is prohibited until the conditions are remedied or the cruise control system is turned OFF and back ON again using the main switch on the cruise control switch.
1.

"CRUISE NOT AVAILABL"

2.

Illuminate

3.

Sound Once

4.

Flash






DIAGNOSIS


a.

If a malfunction occurs in the dynamic laser cruise control system, the ECM actuates the automatic cancel control and blinks the CRUISE main indicator light to inform the driver of a malfunction during cruise control. At this time, the ECM memorizes the malfunction in the form of 5-digit DTCs (Diagnostic Trouble Codes).

i.

The 5-digit DTCs can be read by connecting a Techstream to the DLC3. For details, refer to the Repair Manual.