Home › General › BODY › BODY STRUCTURE
NM27L0U _V1 General _050236 BODY _0250085 BODY STRUCTURE UN GENERAL/CONTROL/DETAILS F

BODY  BODY STRUCTURE  GENERAL/CONTROL/DETAILS  SAFETY FEATURES  


General


a.

The impact absorbing structure of the '08 Sequoia can effectively help reduce the impact in the event of a front, or rear collision. This structure also realizes high-performance occupant protection through the use of reinforcements and members that help minimize cabin deformation.



Impact Absorbing Structure for Frontal Collision


a.

A high-strength, high-rigidity frame structure with axial-compression collision safety is used. This frame structure helps minimize frame buckling as much as possible, and reduces the amount of offset between the load application point and the frame buckling point when a collision occurs.

V116048C01
3.979,0.865 4.583,0.354 true 3.979,4.208 4.531,3.646 true 3.698,3.188 3.917,3.448 0.219,0.26 10 false *a 3.719,4.406 3.979,4.656 0.26,0.25 10 false *b 1.25,4.021 1.469,4.25 0.219,0.229 10 false *c 4.552,3.531 4.792,3.792 0.24,0.26 10 false *d 1.25,0.813 1.469,1.042 0.219,0.229 10 false *c 4.604,0.229 4.854,0.469 0.25,0.24 10 false *d
*a Top View *b Side View
*c Offset *d Buckling Point
V100136

Impact - -



b.

The frame undergoes an axial compressive deformation in order to efficiently absorb the front impact energy and help minimize cabin deformation.

V116049C01
3.354,2.49 3.646,2.115 false 3.229,2.469 3.479,2.698 0.25,0.229 10 false *a
*a Axial Compressive Deformation - -



c.

The frame undergoes an axial compressive deformation in order to efficiently absorb the front impact energy and help minimize cabin deformation.

V116050C01
5.51,1.198 6.021,0.958 false 5.51,2.167 5.938,2.438 false 3.875,3.26 4.156,3.469 0.281,0.208 10 false *a 6.042,0.833 6.25,1.063 0.208,0.229 10 false *1 3.635,6.469 3.927,6.708 0.292,0.24 10 false *b 5.979,2.365 6.219,2.625 0.24,0.26 10 false *1
*1 Floor Under Reinforcements - -
*a Front Impact Energy Distribution Structure *b Frame and Body Integrated Deformation Structure
V100136

Front Impact Energy - -



d.

Except for the very front, high-strength steel sheet is used for all side members to secure stable energy absorption at the time of a collision.


e.

Large cross-section structure for the side rails secures vertical bending rigidity.

V116051C01
2.563,1.729 2.115,1.344 false 1.948,1.198 2.167,1.458 0.219,0.26 10 false *1 5.438,5.375 5.708,5.615 0.271,0.24 10 false *a 5.323,3.188 5.573,3.406 0.25,0.219 10 false *b 6.24,4.188 6.49,4.417 0.25,0.229 10 false *c 3.344,2.219 3.573,2.448 0.229,0.229 10 false A 3.906,2.698 4.146,2.969 0.24,0.271 10 false A
*1 Floor Under Reinforcements - -
*a A - A Cross Section *b 90 mm (3.5 in.)
*c 180 mm (7.1 in.) - -
V100145

Front Impact Energy - -



f.

The reinforcement is used for the frame kick section to help minimize frame deformation around the fuel tank and help prevent the leakage of fuel at the time of a collision.

V116052C01
2.365,1.49 2.583,1.167 true 3.531,1.448 3.063,0.979 true 2.208,1.448 2.458,1.698 0.25,0.25 10 false *1 3.573,1.427 3.865,1.677 0.292,0.25 10 false *2
*1 Fuel Tank *2 Reinforcement
V100136

Rear Impact Energy - -



g.

A cross member is used for the front lower section of the frame to prevent a low-height vehicle from getting under the vehicle in the event of a collision, thereby realizing good compatibility with passenger vehicles.

V116358C01
1.75,3.104 2.167,2.688 false 1.583,3.042 1.844,3.333 0.26,0.292 10 false *1
*1 Cross Member - -



h.

Energy absorbing pads are provided in the door panels and door trims to help dampen the impact applied from the sides of the vehicle to the occupants.

V116359C01
2.552,1.563 3,2 true 6.49,2.031 6.052,1.531 true 3.021,1.979 3.281,2.219 0.26,0.24 10 false *1 1.76,2.406 2.021,2.635 0.26,0.229 10 false *a 5.313,2.448 5.604,2.708 0.292,0.26 10 false *b 6.51,2.01 6.771,2.25 0.26,0.24 10 false *1
*1 Energy Absorbing Pad - -
*a Front *b Rear




Lessening Pedestrian Head Injury


a.

In order to enhance the pedestrian protection performance, the engine hood has been designed with a longitudinal frame structure which brings uniform engine hood rigidity and efficiently absorbs the impact.


b.

An impact absorption shape has been provided at the front of the engine hood. If someone short such as a child hits the front, the impact will be absorbed more efficiently, helping minimize head injuries.

V116360C01
1.427,3.177 1.74,2.823 true 5.365,1.833 4.823,1.292 true 1.302,3.156 1.563,3.385 0.26,0.229 10 false *1 5.75,2.896 6.01,3.229 0.26,0.333 10 false *a 4.656,1.146 4.927,1.417 0.271,0.271 10 false *b 1.927,2.938 2.104,3.135 0.177,0.198 10 false A 1.958,2.208 2.135,2.406 0.177,0.198 10 false A
*1 Engine Hood - -
*a A - A Cross Section *b Impact Absorption Shape