Home › General › INTRODUCTION › HOW TO USE THIS MANUAL
RM27L0U _V1 General _049289 INTRODUCTION _0235379 HOW TO USE THIS MANUAL F

INTRODUCTION  HOW TO USE THIS MANUAL  GENERAL INFORMATION  


GENERAL DESCRIPTION


a.

This manual is written in accordance with SAE J2008.

i.

Diagnosis


ii.

Removing / Installing, Replacing, Disassembling / Reassembling, Checking and Adjusting


iii.

Final Inspection



b.

The following procedures are omitted from this manual. However, these procedures must be performed.

i.

Use a jack or lift to perform operations


ii.

Clean all removed parts


iii.

Perform a visual check




INDEX


a.

An alphabetical INDEX section is provided at the end of the manual as a reference to help you find the item to be repaired.



PREPARATION


a.

Use of Special Service Tools (SST) and Special Service Materials (SSM) may be required, depending on the repair procedure. Be sure to use SST and SSM when they are required and follow the working procedure properly. A list of SST and SSM is in the "Preparation" section of this manual.



REPAIR PROCEDURES


a.

A component illustration is placed under the title where necessary.


b.

Non-reusable parts, grease application areas, precoated parts and torque specifications are noted in the component illustrations.

The following illustration is an example.


U152685E02
0.24,3.219 1.573,3.438 1.333,0.219 3.042,1.875 3.625,2.042 0.583,0.167 0.406,2.271 1.052,2.438 0.646,0.167 2.792,1.958 3.042,1.958 false 0.917,1.635 0.698,1.635 false 1.51,0.531 1.76,0.531 false 1.74,1.146 1.5,1.146 false 1.125,2.802 0.948,2.802 false 1.781,2.167 2.01,1.594 2.01,1.594 2.104,1.594 false 1.052,2.354 1.177,2.354 false 4.156,2.208 4.156,2.656 false 6.281,1.854 6.281,1.688 false 5.896,1.75 5.896,2.135 false 3.188,2.51 3.188,2.667 false 4.958,2.063 4.958,2.396 false 5.26,2.01 5.26,2.146 false 4.677,1.896 4.677,1.615 4.677,1.615 4.552,1.615 false 5.573,1.375 5.573,1.208 5.573,1.208 5.49,1.208 false 0.802,0.844 1.052,0.844 false 5.802,1.333 5.802,1.073 5.802,1.073 5.885,1.073 false 1.792,0.458 2.698,0.625 0.906,0.167 10 false FILTER CAP 0.365,0.75 0.885,0.927 0.521,0.177 10 false FLOAT 1.781,1.052 3.198,1.208 1.417,0.156 10 false RESERVOIR TANK 0.063,1.552 0.896,1.885 0.833,0.333 10 false SLOTTED SPRING PIN 0.26,2.719 1.083,2.917 0.823,0.198 10 false CYLINDER 2.969,2.708 3.583,2.875 0.615,0.167 10 false PISTON 3.76,2.688 4.625,2.865 0.865,0.177 10 false PUSH ROD 4.573,2.427 5.385,2.583 0.813,0.156 10 false SNAP RING 5.094,2.167 5.563,2.354 0.469,0.188 10 false BOOT 5.635,2.177 6.385,2.344 0.75,0.167 10 false LOCK NUT 6.073,1.885 6.635,2.042 0.563,0.156 10 false CLEVIS 5.927,0.979 6.792,1.135 0.865,0.156 10 false CLEVIS PIN 3.917,1.51 4.635,1.688 0.719,0.177 10 false WASHER 1.646,3.24 2.813,3.406 1.167,0.167 10 false : Specified torque 0.302,3.24 1.656,3.396 1.354,0.156 10 false N*m (kgf*cm, ft.*lbf) 0.448,3.51 1.813,3.667 1.365,0.156 10 false Non-reusable part 4.885,1.125 5.521,1.302 0.635,0.177 10 false GASKET 2.313,1.51 3.135,1.698 0.823,0.188 10 false GROMMET 3.052,1.885 3.677,2.021 0.625,0.135 8 false 12 (120, 9) 0.417,2.281 1.073,2.417 0.656,0.135 8 false 15 (155, 11) 0.271,0.083 1.094,0.281 0.823,0.198 10 false Example:


c.

Torque specifications, grease application areas and non-reusable parts are emphasized in the procedures.

HINT:

There are cases where such information can only be explained by using an illustration. In these cases, the information is described in the illustration.



d.

Only items with key points are described in the text. What to do and other details are explained using illustrations next to the text. Both the text and illustrations are accompanied by standard values and notices.

Illustration What to do and where to do it
Task heading What work will be performed
Explanation text How to perform the task
Also has information such as specifications and warnings, which are written in boldface text


e.

Illustrations of similar vehicle models are sometimes used. In these cases, minor details may be different from the actual vehicle.


f.

Procedures are presented in a step-by-step format.



SERVICE SPECIFICATIONS


a.

SPECIFICATIONS are presented in boldface text throughout the manual. The specifications are also found in the "Service Specifications" section for reference.



TERM DEFINITIONS


CAUTION Possibility of injury to you or other people.
NOTICE Possibility of damage to components being repaired.
HINT Provides additional information to help you perform repairs.


INTERNATIONAL SYSTEM OF UNITS


a.

The units used in this manual comply with the International System of Units (SI) standard. Units from the metric system and the English systems are also provided.

Example:


Torque:
30 N*m (310 kgf*cm, 22 ft.*lbf)