Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › THROTTLE BODY
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235518 THROTTLE BODY A

3UR-FBE ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the throttle body assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 22030 1.INSTALL THROTTLE BODY ASSEMBLY

a.
A313317E01
1.625,1.052 2.125,0.396 2.125,0.396 2.26,0.396 false 1.281,1.573 1.531,1.958 1.531,1.958 1.688,1.958 false 1.5,0.375 1.063,0.375 false 0.74,1.479 0.573,1.073 0.573,1.073 0.438,1.073 false 2.281,0.292 2.469,0.458 0.188,0.167 10 false *a 1.688,1.865 1.875,2.031 0.188,0.167 10 false *a 0.875,0.281 1.031,0.448 0.156,0.167 10 false *1 0.25,0.99 0.406,1.156 0.156,0.167 10 false *2

Install the No. 5 water by-pass hose to the throttle body assembly, and slide the clamp to secure the hose.

Text in Illustration
*1 No. 5 Water By-pass Hose
*2 No. 4 Water By-pass Hose
*a White Mark

HINT:

Make sure the hose color is shown in the illustration.



b.

Install the No. 4 water by-pass hose to the throttle body assembly, and slide the clamp to secure the hose.

HINT:

Make sure the hose color is shown in the illustration.



c.
A165587E03
1.698,0.729 2.01,0.292 true 2,0.302 2.167,0.302 true 2.313,1.302 2.458,0.854 true 2.458,0.854 2.51,0.854 false 0.375,2.74 0.583,2.938 0.208,0.198 10 false *c 2.906,2.74 3.125,2.938 0.219,0.198 10 false *d 2.219,0.219 2.427,0.385 0.208,0.167 10 true *a 2.542,0.771 2.76,0.979 0.219,0.208 10 true *b

Align the protrusion of the gasket with the groove of the intake manifold.

Text in Illustration
*a Groove
*b Protrusion
*c Intake Manifold Side
*d Throttle Body Side


d.

Install a new gasket to the intake manifold.


e.

Install the throttle body assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

Perform "Inspection After Repairs" after replacing the throttle body assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).



f.

Connect the throttle body connector.


g.
A313318E01
0.573,1.5 0.938,1.281 0.938,1.281 1.042,1.281 true 0.688,0.979 0.531,0.677 0.531,0.677 0.427,0.677 true 2.021,0.781 2.573,0.24 2.573,0.24 2.656,0.24 true 2.167,1 1.948,1.427 1.948,1.427 1.833,1.427 true 1.052,1.198 1.219,1.354 0.167,0.156 10 true *a 0.229,0.583 0.396,0.74 0.167,0.156 10 true *1 2.667,0.146 2.833,0.302 0.167,0.156 10 false *2 1.635,1.344 1.802,1.5 0.167,0.156 10 true *b

Connect the No. 5 water by-pass hose to the water inlet housing, and slide the clamp to secure the hose.

Text in Illustration
*1 No. 5 Water By-pass Hose
*2 No. 4 Water By-pass Hose
*a Yellow Mark
*b Pink Mark

HINT:

Make sure the hose color is shown in the illustration.



h.

Connect the No. 4 water by-pass hose to the No. 3 water by-pass pipe, and slide the clamp to secure the hose.

HINT:

Make sure the hose color is shown in the illustration.



Hide 5.PERFORM INITIALIZATION

NOTICE:
·

Be sure to perform this procedure after reassembling the throttle body assembly or removing and reinstalling any throttle body component.

·

Be sure to perform this procedure after reconnecting the battery cable and replacing the ECM.



a.

Disconnect the EFI fuse and ETCS fuse at the same time. Wait at least 60 seconds and reconnect the fuses.


b.

Turn the ignition switch to ON without operating the accelerator pedal.

NOTICE:

If the accelerator pedal is operated, perform the above steps again.



c.

Connect the Techstream to the DLC3 and clear the DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).


d.

Start the engine and check that the MIL is not illuminated and that the idle speed is within the specified range when the A/C is switched off after the engine is warmed up.

Standard:
Condition Engine Idle Speed
A/C switched off 650 to 750 rpm


NOTICE:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in N of P.




e.

Enter the following menus: Powertrain / Engine and ETC / Data List / All Data / Throttle Sensor Position. Sensor Output. Fully depress the accelerator pedal and check that the value is 60% or more.


f.

Perform a road test and confirm that there are no abnormalities.