Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › MASS AIR FLOW METER
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235521 MASS AIR FLOW METER G

3UR-FBE ENGINE CONTROL  MASS AIR FLOW METER  INSPECTION  


PROCEDURE

Hide 22204 1.INSPECT MASS AIR FLOW METER

a.

Check the output voltage.

i.
A165594E07
2.625,1.792 2.698,1.792 2.698,1.792 2.615,2.792 false 2.781,1.365 2.896,1.365 2.896,1.365 2.729,2.802 false 2.448,2.865 2.333,3.313 2.333,3.313 2.198,3.313 false 0.24,3.656 0.49,3.865 0.25,0.208 10 false Air 2.344,1.292 2.76,1.458 0.417,0.167 10 false 1 (+B) 2.125,1.708 2.635,1.875 0.51,0.167 10 false 2 (E2G) 1.729,3.229 2.177,3.406 0.448,0.177 10 false 3 (VG) 0.094,0.177 2.667,0.583 2.573,0.406 10 false Component without harness connected: (MAF Meter)

Apply battery voltage across terminals 1 (+B) and 2 (E2G).

NOTICE:

While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.



ii.

Using a voltmeter, connect the positive (+) tester probe to terminal 3 (VG), and negative (-) tester probe to terminal 2 (E2G).


iii.

Blow air into the MAF meter, and check that the voltage fluctuates.

If the result is not as specified, replace the MAF meter.



b.
A165595E01
1.944,1.488 2.834,1.902 0.891,0.414 10 Platinum Hot Wire (Heater) 1.312,2.466 1.838,1.625 false 1.838,1.625 1.915,1.625 false

Perform a visual check for any foreign matter on the platinum hot wire (heater) of the mass air flow meter shown in the illustration.

OK:

There is no foreign material.


If the result is not as specified, replace the mass air flow meter.


c.

Check the IAT sensor.

A380325E01
1.604,1.552 1.896,1.219 1.896,1.219 2.031,1.219 true 1.479,1.563 1.24,1.208 1.24,1.208 1.125,1.208 true 5.417,1.042 5.708,0.708 5.708,0.708 5.844,0.708 true 0.323,0.167 2.896,0.813 2.573,0.646 10 false Component without harness connected: (MAF Meter) 0.688,1.125 1.604,1.323 0.917,0.198 10 false 5 (E2) 2.094,1.135 3.167,1.333 1.073,0.198 10 false 4 (THA) 3.26,0.052 5.25,0.25 1.99,0.198 10 false Resistance kΩ 4.219,0.094 4.531,0.292 0.313,0.198 10 false 20 4.229,0.333 4.542,0.531 0.313,0.198 10 false 10 4.26,0.604 4.417,0.802 0.156,0.198 10 false 5 4.26,0.781 4.417,0.979 0.156,0.198 10 false 3 4.26,0.938 4.417,1.135 0.156,0.198 10 false 2 4.26,1.167 4.417,1.365 0.156,0.198 10 false 1 4.188,1.458 4.646,1.656 0.458,0.198 10 false 0.5 4.188,1.656 4.646,1.854 0.458,0.198 10 false 0.3 4.188,1.802 4.646,2 0.458,0.198 10 false 0.2 4.198,2.063 4.656,2.26 0.458,0.198 10 false 0.1 3.01,2.323 4.26,2.708 1.25,0.385 10 false Temperature °C (°F) 4.49,2.333 4.948,2.531 0.458,0.198 10 false -20 4.896,2.333 5.052,2.531 0.156,0.198 10 false 0 5.198,2.333 5.51,2.531 0.313,0.198 10 false 20 5.542,2.333 5.854,2.531 0.313,0.198 10 false 40 5.865,2.333 6.177,2.531 0.313,0.198 10 false 60 6.198,2.333 6.51,2.531 0.313,0.198 10 false 80 6.51,2.333 6.969,2.531 0.458,0.198 10 false 100 4.51,2.5 5.125,2.698 0.615,0.198 10 false (-4) 4.833,2.5 5.448,2.698 0.615,0.198 10 false (32) 5.167,2.5 5.781,2.698 0.615,0.198 10 false (68) 5.469,2.5 6.24,2.698 0.771,0.198 10 false (104) 5.802,2.5 6.573,2.698 0.771,0.198 10 false (140) 6.135,2.5 6.906,2.698 0.771,0.198 10 false (176) 6.49,2.49 7.135,2.688 0.646,0.198 10 false (212) 5.885,0.635 6.823,0.99 0.938,0.354 10 false Acceptable

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (THA) - 5 (E2) -20°C (-4°F) 12.5 k to 16.9 kΩ
20°C (68°F) 2.19 k to 2.67 kΩ
60°C (140°F) 0.50 k to 0.68 kΩ


If the result is not as specified, replace the MAF meter.