Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › KNOCK SENSOR
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235526 KNOCK SENSOR A

3UR-FBE ENGINE CONTROL  KNOCK SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the knock sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 89615 1.INSTALL KNOCK SENSOR

a.
A184969E04
1.833,3.104 2.031,3.271 0.198,0.167 10 false *e 3.021,2.49 3.198,2.656 0.177,0.167 10 false *f 2.427,0.802 2.667,1 0.24,0.198 10 true *c 0.24,1.271 0.427,1.427 0.188,0.156 10 true *e 0.833,0.813 1.031,0.99 0.198,0.177 10 true *a 0.844,1.229 1.052,1.385 0.208,0.156 10 true *b 2.396,1.24 2.594,1.396 0.198,0.156 10 false *d 0.083,2.323 0.271,2.5 0.188,0.177 10 false *a 0.229,3.115 0.417,3.281 0.188,0.167 10 false *e 0.646,2.479 0.833,2.646 0.188,0.167 10 false *f 2.177,3.083 2.354,3.25 0.177,0.167 10 false 2° 2.115,2.906 2.365,3.063 0.25,0.156 10 false 10° 1.479,3.073 1.667,3.25 0.188,0.177 10 false 2° 1.417,2.917 1.667,3.073 0.25,0.156 10 false 10° 3.052,4.24 3.229,4.406 0.177,0.167 10 false 2° 3,4.073 3.26,4.229 0.26,0.156 10 false 10° 0.438,4.25 0.615,4.396 0.177,0.146 10 false 2° 0.385,4.073 0.625,4.24 0.24,0.167 10 false 10° 1.771,3.51 1.958,3.688 0.188,0.177 10 false *d 1.76,4.26 1.938,4.438 0.177,0.177 10 false *g 2.208,3.656 2.365,3.823 0.156,0.167 10 false *f 0.083,3.51 0.281,3.698 0.198,0.188 10 false *b 0.094,4.271 0.271,4.458 0.177,0.188 10 false *g 1.281,3.656 1.458,3.823 0.177,0.167 10 false *f 1.771,2.323 1.969,2.5 0.198,0.177 10 false *c

Install the 4 knock sensor with the 4 bolts so that the knock sensors are angled as shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

Text in Illustration
*a Bank 2 Sensor 1
*b Bank 1 Sensor 1
*c Bank 2 Sensor 2
*d Bank 1 Sensor 2
*e Front
*f Upper
*g Rear

NOTICE:

The acceptable installation angle of the knock sensor is between 10° upward and 2° downward from the horizontal position.


HINT:

Perform "Inspection After Repairs" after replacing the knock sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).



b.

Connect the 4 knock sensor connectors.